[cisco-voip] FXO Outbound Call Not Working

Kim, Hyoun S Hyoun.Kim at chartercom.com
Mon Jun 14 14:45:03 EDT 2010


Thanks all.  I appreciate the input.  When I asked the Local IT Admin about more details, he said prior to the weekend (ever since I installed the system), everything was fine.  But then they got terrible storms over the weekend in Alabama and that's when phones weren't responsive.  He rebooted the router and then that's when we got the symptoms I mentioned earlier (inbound calls ok, outbound no good).

I'm having him track down a buttset to use for final testing before calling AT&T.

Hyoun Kim
Network Administrator
Charter Media - East Division
640 Broadmor Blvd, Suite 80
Murfreesboro, TN 37129

Email: Hyoun.Kim at chartercom.com<mailto:Hyoun.Kim at chartercom.com>
Office: 615.217.6245
Fax: 615.217.6247

From: Erick B. [mailto:erickbee at gmail.com]
Sent: Monday, June 14, 2010 1:06 PM
To: Kim, Hyoun S
Cc: Dennis Heim; ccieid1ot; cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] FXO Outbound Call Not Working

The next step would be like I said, try out each line disconnected from router FXO port with a old POTS / princess phone and see if the phone lines work, or use a Butt Sett on them like Dennis suggested.

The 0x00 is indication of router voice-port seeing no voltage on the line plugged into that port (maybe there is nothing plugged into the port, or it got disconnected somewhere upstream). This command however gives you more of a warm fuzzy then anything. With analog lines, there is no real good way from router command line to really tell what is going on with the actual phone lines. The no circuit on the call history means the router attempted to make a call but didn't detect a phone line / dial tone on that port to do so.

But, most likely a telephone provider / phone line cabling issue since this used to work fine with no changes on your gateway.

On Mon, Jun 14, 2010 at 10:07 AM, Kim, Hyoun S <Hyoun.Kim at chartercom.com<mailto:Hyoun.Kim at chartercom.com>> wrote:
I'm having a local IT guy from down there to try it.  I can't because I'm over 300 miles away.

In the event that phone calls cannot be made outbound, what needs to be done given the e-mail I wrote out below?

Hyoun Kim
Network Administrator
Charter Media - East Division
640 Broadmor Blvd, Suite 80
Murfreesboro, TN 37129

Email: Hyoun.Kim at chartercom.com<mailto:Hyoun.Kim at chartercom.com>
Office: 615.217.6245
Fax: 615.217.6247

From: Dennis Heim [mailto:Dennis.Heim at cdw.com<mailto:Dennis.Heim at cdw.com>]
Sent: Monday, June 14, 2010 9:07 AM
To: Kim, Hyoun S; Erick B.; ccieid1ot

Cc: cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
Subject: RE: [cisco-voip] FXO Outbound Call Not Working

If you connect your butt-set to these lines do they work?

Dennis Heim
Network Voice Engineer
CDW  Advanced Technology Services
11711 N. Meridian Street, Suite 225
Carmel, IN  46032

317.569.4255 Office
317.569.4201 Fax
317.694.6070 Cell
dennis.heim at cdw.com<mailto:dennis.heim at cdw.com>
cdw.com/content/solutions/unified-communications/<http://www.cdw.com/content/solutions/unified-communications/>


From: cisco-voip-bounces at puck.nether.net<mailto:cisco-voip-bounces at puck.nether.net> [mailto:cisco-voip-bounces at puck.nether.net<mailto:cisco-voip-bounces at puck.nether.net>] On Behalf Of Kim, Hyoun S
Sent: Monday, June 14, 2010 9:53 AM
To: Erick B.; ccieid1ot
Cc: cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
Subject: Re: [cisco-voip] FXO Outbound Call Not Working

Oh sorry Erick.

The hardware is a C2811 with 3 VIC2-4FXO cards utilizing 12 analog phone lines from the telco (AT&T).  I have 2 DSP modules (PVDM2-16 & 64) installed with a NM-CUE module installed as well.

All of the lines exhibit the same problem where people can dial to the office and the phone rings.  But outbound calls by that office do not work and display that same error I showed in the first e-mail.  I attempted to use the groundstart command on my voice ports per CCIEID1OT's recommendation, but that didn't work either.

Thanks for that call command.  Here is the output for outbound calls... I see the "no circuit 34" you mentioned!
15B7 : 347 246488340ms.346 +-1 +1260 pid:6 Originate 16152176245
 dur 00:00:00 tx:0/0 rx:0/0 22  (no circuit (34))
 Telephony 0/0/0 (347) [0/0/0] tx:0/0/0ms None noise:0dBm acom:0dBm
  long duration call detected:n long dur callduration :n/a timestamp:n/a

Also, here are the results from the test voice command you gave me:
005578: Jun 14 08:50:42.880 CDT:
Values read from SiLabs Codec connected to DSP 0, channel 8:
--------------------------------------------------------------
Register 29 = 0xD5

I noticed the Register 29 comes out with different values for different ports.  Such as 0x00, 0xD5 & 0xD4.

What are your recommendations since I get the "no circuit 34"?  The only thread I saw in regards to my initial error on Cisco's support forums is this: https://supportforums.cisco.com/message/3118805#3118805

However, the user ended up saying that the Telco was at fault and that's how he got it fixed.  I just wanted to make sure all my hardware was ok before tell AT&T because in the past, they always tell me to check my equipment first.

Thanks so much.

Hyoun Kim
Network Administrator
Charter Media - East Division
640 Broadmor Blvd, Suite 80
Murfreesboro, TN 37129

Email: Hyoun.Kim at chartercom.com<mailto:Hyoun.Kim at chartercom.com>
Office: 615.217.6245
Fax: 615.217.6247

From: Erick B. [mailto:erickbee at gmail.com<mailto:erickbee at gmail.com>]
Sent: Friday, June 11, 2010 11:51 PM
To: ccieid1ot
Cc: Kim, Hyoun S; cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
Subject: Re: [cisco-voip] FXO Outbound Call Not Working

I would start by making sure each of the analog lines worked fine, with a regular old princess phone, if possible. Since it was working fine, and config hasn't changed, it's likely an issue with the phone lines or cabling.

You don't mention what type of hardware you have, but try reseating the cables, especially if you have a amphenol connector. Those tend to vibrate loose over time and cause problems like this, where calls fail but some work depending on what port is being used.

Output from 'show call history voice brief' may be useful. If the cause/reason states no circuit 34 then the line may be a problem.

If you have a ISR router, you can try this, but it varies with voice-card hardware, a 0x0 result indicates the router see's no voltage on whatever is attached to the voice-port.

term mon
test voice port x/y/z si-reg-read 29 1

Where x/y/z is your voice-port #/#/#, you need term mon to see the output from the test command.


On Fri, Jun 11, 2010 at 3:27 PM, ccieid1ot <ccieid1ot at gmail.com<mailto:ccieid1ot at gmail.com>> wrote:
Try changing to ground-start.
On Fri, Jun 11, 2010 at 2:43 PM, Kim, Hyoun S <Hyoun.Kim at chartercom.com<mailto:Hyoun.Kim at chartercom.com>> wrote:
I have a router that I've utilizes FXO modules for making calls.  When I first set it up, everything worked fine.  A few months later, users started reporting to me an intermittent problem for outbound calls.  Sometimes they can make calls, but the majority of the time, they get a fast busy signal.  I compared the current router's configuration to when I originally saved the configuration from initial setup.  Nothing changed.  Out of perhaps 10 calls made, maybe 1 of them went through.

The following is the config for a voice-port.  All the other ones have the same config.  2857 is the number to the Unity Express.
voice-port 0/0/0
 trunk-group POTS-FXO
 connection plar opx 2857
caller-id enable

I did try "no supervisory disconnect signal" but that didn't work either.

I turned on debugging for "vpm signal" and made several calls to different phone numbers.  The following output is just an example of what the result is for all calls:
001401: Jun 11 14:36:33.104 CDT: htsp_digit_ready(50/0/10.1): digit = 1
001402: Jun 11 14:36:33.500 CDT: htsp_digit_ready(50/0/10.1): digit = 6
001403: Jun 11 14:36:33.832 CDT: htsp_digit_ready(50/0/10.1): digit = 1
001404: Jun 11 14:36:34.124 CDT: htsp_digit_ready(50/0/10.1): digit = 5
001405: Jun 11 14:36:34.548 CDT: htsp_digit_ready(50/0/10.1): digit = 2
001406: Jun 11 14:36:34.816 CDT: htsp_digit_ready(50/0/10.1): digit = 1
001407: Jun 11 14:36:35.204 CDT: htsp_digit_ready(50/0/10.1): digit = 7
001408: Jun 11 14:36:35.636 CDT: htsp_digit_ready(50/0/10.1): digit = 6
001409: Jun 11 14:36:35.904 CDT: htsp_digit_ready(50/0/10.1): digit = 3
001410: Jun 11 14:36:36.308 CDT: htsp_digit_ready(50/0/10.1): digit = 0
001411: Jun 11 14:36:36.576 CDT: htsp_digit_ready(50/0/10.1): digit = 0
001412: Jun 11 14:36:36.588 CDT: htsp_timer_stop3
001413: Jun 11 14:36:36.588 CDT: htsp_process_event: [50/0/10.1, EFXS_OFFHOOK, E_HTSP_PROCEEDING]efxs_offhook_proceeding
001414: Jun 11 14:36:36.588 CDT: [50/0/10.1] set signal state = 0x8 timestamp = 0htsp_setup_req
001415: Jun 11 14:36:36.592 CDT: htsp_process_event: [0/0/0, FXOLS_ONHOOK, E_HTSP_SETUP_REQ]fxols_onhook_setup
001416: Jun 11 14:36:36.592 CDT: [0/0/0] set signal state = 0xC timestamp = 0
001417: Jun 11 14:36:36.592 CDT: htsp_timer - 1300 msec
001418: Jun 11 14:36:36.844 CDT: htsp_process_event: [0/0/0, FXOLS_WAIT_DIAL_TONE, E_DSP_SIG_1100]fxols_power_denial_detected
001419: Jun 11 14:36:36.844 CDT: htsp_timer2 - 1000 msec
001420: Jun 11 14:36:36.844 CDT: htsp_timer_stop
001421: Jun 11 14:36:37.844 CDT: htsp_process_event: [0/0/0, FXOLS_WAIT_DIAL_TONE, E_HTSP_EVENT_TIMER2]fxols_power_den_disc
001422: Jun 11 14:36:37.844 CDT: htsp_timer_stop
001423: Jun 11 14:36:37.844 CDT: htsp_timer_stop2
001424: Jun 11 14:36:37.844 CDT: [0/0/0] set signal state = 0x4 timestamp = 0
001425: Jun 11 14:36:37.848 CDT: htsp_process_event: [0/0/0, FXOLS_ONHOOK, E_HTSP_RELEASE_REQ]fxols_onhook_release
001426: Jun 11 14:36:54.497 CDT: htsp_process_event: [50/0/10.1, EFXS_OFFHOOK, E_DSP_SIG_0100]efxs_offhook_onhook
001427: Jun 11 14:36:54.497 CDT: htsp_timer - 10 msec
001428: Jun 11 14:36:54.509 CDT: htsp_process_event: [50/0/10.1, EFXS_OFFHOOK, E_HTSP_EVENT_TIMER]efxs_offhook_timer
001429: Jun 11 14:36:54.513 CDT: htsp_process_event: [50/0/10.1, EFXS_ONHOOK, E_HTSP_RELEASE_REQ]efxs_onhook_release
001430: Jun 11 14:36:54.513 CDT: htsp_timer_stop
001431: Jun 11 14:36:54.513 CDT: [50/0/10.1] set signal state = 0x4 timestamp = 0

Thanks for any help.
[cid:image001.jpg at 01CB0BC7.CABCCF40]
________________________________
Hyoun Kim * Network Administrator - East Division
640 Broadmor Blvd * Suite 80 * Murfreesboro, TN 37129
' 615.217.6245 * 7 615.217.6247 * * Hyoun.Kim at chartercom.com<mailto:Hyoun.Kim at chartercom.com>




E-MAIL CONFIDENTIALITY NOTICE:

















The contents of this e-mail message and

any attachments are intended solely for the

addressee(s) and may contain confidential

and/or legally privileged information. If you

are not the intended recipient of this message

or if this message has been addressed to you

in error, please immediately alert the sender

 by reply e-mail and then delete this message

and any attachments. If you are not the

intended recipient, you are notified that

any use, dissemination, distribution, copying,

or storage of this message or any attachment

is strictly prohibited.

















_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
https://puck.nether.net/mailman/listinfo/cisco-voip


_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
https://puck.nether.net/mailman/listinfo/cisco-voip







E-MAIL CONFIDENTIALITY NOTICE:











































The contents of this e-mail message and





any attachments are intended solely for the





addressee(s) and may contain confidential





and/or legally privileged information. If you





are not the intended recipient of this message





or if this message has been addressed to you





in error, please immediately alert the sender





 by reply e-mail and then delete this message





and any attachments. If you are not the





intended recipient, you are notified that





any use, dissemination, distribution, copying,





or storage of this message or any attachment





is strictly prohibited.































E-MAIL CONFIDENTIALITY NOTICE:















The contents of this e-mail message and

any attachments are intended solely for the

addressee(s) and may contain confidential

and/or legally privileged information. If you

are not the intended recipient of this message

or if this message has been addressed to you

in error, please immediately alert the sender

 by reply e-mail and then delete this message

and any attachments. If you are not the

intended recipient, you are notified that

any use, dissemination, distribution, copying,

or storage of this message or any attachment

is strictly prohibited.
















E-MAIL CONFIDENTIALITY NOTICE: 

 

 

 

The contents of this e-mail message and 
any attachments are intended solely for the 
addressee(s) and may contain confidential 
and/or legally privileged information. If you 
are not the intended recipient of this message 
or if this message has been addressed to you 
in error, please immediately alert the sender
 by reply e-mail and then delete this message 
and any attachments. If you are not the 
intended recipient, you are notified that 
any use, dissemination, distribution, copying, 
or storage of this message or any attachment 
is strictly prohibited.







-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100614/0545bef3/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 1990 bytes
Desc: image001.jpg
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100614/0545bef3/attachment.jpg>


More information about the cisco-voip mailing list