[cisco-voip] SIP trunk one way audio

Mon Nov 15 10:33:39 EST 2010

Unless you are using inband DTMF it will be required.

On Nov 15, 2010, at 7:07 AM, Bill Riley wrote:

> I don’t think that’s correct. It needs access to an MTP but you shouldn’t need to use the MTP required checkbox on the trunk.
>  
>  
> From: Mark Holloway [mailto:mh at markholloway.com] 
> Sent: Friday, November 12, 2010 12:24 PM
> To: Bill Riley
> Cc: 'Ryan Ratliff'; cisco-voip at puck.nether.net
> Subject: Re: [cisco-voip] SIP trunk one way audio
>  
> CUCM needs it assigned to the trunk for DTMF to work properly for calls egressing the SIP Trunk.
>  
> On Nov 12, 2010, at 10:50 AM, Bill Riley wrote:
> 
> 
> I don’t think that is correct. It should only need to have one available in the MRGL, not one allocated every time a call comes in.
>  
>  
> voice service voip
> ip address trusted list
>   ipv4 x.x.x.x
>   ipv4 x.x.x.x
>   ipv4 x.x.x.x
> allow-connections h323 to h323
> allow-connections h323 to sip
> allow-connections sip to h323
> allow-connections sip to sip
> no supplementary-service sip moved-temporarily
> no supplementary-service sip refer
> fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 fallback none
> h323
> modem passthrough nse codec g711ulaw
> sip
>   bind control source-interface Serial0/0/0:1
>   bind media source-interface Serial0/0/0:1
>   early-offer forced
>   midcall-signaling passthru
> !
>  
>  
> voice class codec 100
> codec preference 1 g711ulaw
> codec preference 2 g729r8
> !
> !        
> dial-peer voice 201 voip
> preference 1
> destination-pattern 91[2-9]..[2-9]......
> rtp payload-type cisco-codec-fax-ind 98
> rtp payload-type comfort-noise 13
> session protocol sipv2
> session target ipv4: x.x.x.x
> dtmf-relay rtp-nte
> codec g711ulaw
> fax rate 14400
> ip qos dscp cs3 signaling
> !
> dial-peer voice 202 voip
> preference 1
> destination-pattern 9[2-9]......T
> rtp payload-type cisco-codec-fax-ind 98
> rtp payload-type comfort-noise 13
> session protocol sipv2
> session target ipv4: x.x.x.x
> dtmf-relay rtp-nte
> codec g711ulaw
> fax rate 14400
> ip qos dscp ef signaling
> !
> dial-peer voice 203 voip
> preference 1
> destination-pattern ^9556[2-9]......
> rtp payload-type cisco-codec-fax-ind 98
> rtp payload-type comfort-noise 13
> session protocol sipv2
> session target ipv4: x.x.x.x
> dtmf-relay rtp-nte
> codec g711ulaw
> fax rate 14400
> ip qos dscp ef signaling
> !
> dial-peer voice 204 voip
> preference 1
> destination-pattern 9555[2-9]......
> rtp payload-type cisco-codec-fax-ind 98
> rtp payload-type comfort-noise 13
> session protocol sipv2
> session target ipv4: x.x.x.x
> dtmf-relay rtp-nte
> fax rate 14400
> ip qos dscp ef signaling
> !
> dial-peer voice 411 voip
> preference 1
> destination-pattern 5555555..
> rtp payload-type cisco-codec-fax-ind 98
> rtp payload-type comfort-noise 13
> session protocol sipv2
> session target ipv4: x.x.x.x
> dtmf-relay rtp-nte
> codec g711ulaw
> fax rate 14400
> ip qos dscp cs3 signaling
> !        
> dial-peer voice 412 voip
> preference 2
> destination-pattern 5555555..
> rtp payload-type cisco-codec-fax-ind 98
> rtp payload-type comfort-noise 13
> session protocol sipv2
> session target ipv4: x.x.x.x
> dtmf-relay rtp-nte
> codec g711ulaw
> fax rate 14400
> ip qos dscp cs3 signaling
> !
> dial-peer voice 413 voip
> preference 3
> destination-pattern 5555555..
> rtp payload-type cisco-codec-fax-ind 98
> rtp payload-type comfort-noise 13
> session protocol sipv2
> session target ipv4: x.x.x.x
> dtmf-relay rtp-nte
> codec g711ulaw
> fax rate 14400
> ip qos dscp cs3 signaling
>  
>  
> From: Mark Holloway [mailto:mh at markholloway.com] 
> Sent: Friday, November 12, 2010 11:32 AM
> To: Bill Riley
> Cc: 'Ryan Ratliff'; cisco-voip at puck.nether.net
> Subject: Re: [cisco-voip] SIP trunk one way audio
>  
> You should have it on the trunk.
>  
> On Nov 12, 2010, at 10:29 AM, Bill Riley wrote:
> 
> 
> 
> Your right, but I don’t need to have the check box to require one on the trunk. It should allocate one from the MRGL on an as needed basis.
>  
> From: Mark Holloway [mailto:mh at markholloway.com] 
> Sent: Friday, November 12, 2010 11:28 AM
> To: Bill Riley
> Cc: 'Ryan Ratliff'; cisco-voip at puck.nether.net
> Subject: Re: [cisco-voip] SIP trunk one way audio
>  
> You should be using an MTP for your SIP trunk to support DTMF. It does not need to be a hardware MTP resource. 
>  
> On Nov 12, 2010, at 10:05 AM, Bill Riley wrote:
> 
> 
> 
> 
> When I change it to MTP required on the sip trunk everything works as expected. The point is that I shouldn’t need to have this configuration.
>  
> From: Ryan Ratliff [mailto:rratliff at cisco.com] 
> Sent: Friday, November 12, 2010 9:00 AM
> To: Bill Riley
> Cc: 'Cheng, Karen'; cisco-voip at puck.nether.net
> Subject: Re: [cisco-voip] SIP trunk one way audio
>  
> I see lots of discussion around config and call flow but have you actually done any troubleshooting?  One way audio most of the time comes down to the simple fact that one party is not receiving RTP from the other.   For these one-way audio calls you need to determine what IP addresses are involved.  Next verify this in the signaling via the SDPs in the SIP messages.   You can then use show commands on the router to confirm where it thinks it should be sending and receiving RTP to/from and if in fact packet counters are incrementing.
>  
> If no MTP is being used for the call, try forcing it to use one and see if that fixes the issue.
> If you are using media flow-through (default) does changing it to flow-around fix the issue? 
>  
> -Ryan
>  
> On Nov 12, 2010, at 8:09 AM, Bill Riley wrote:
> 
> 
> 
> 
> 
> I shouldn’t need an MTP for this connection. All SIP traffic is sourced from one interface.  I do have SCCP traffic sourced from a different interface but it is only used for a conference bridge, not MTP.
>  
> From: Cheng, Karen [mailto:Karen.Cheng at racq.com.au] 
> Sent: Thursday, November 11, 2010 9:14 PM
> To: 'Bill Riley'
> Subject: RE: [cisco-voip] SIP trunk one way audio
>  
> Not sure if you have checked already but is your SIP trunk using one interface and your MTP/SCCP interface a different interface?
>  
> I had one-way audio/no audio problems ages back due to this because our integrator had configured the SIP trunk to point to int gi0/0’s IP and then configured the SCCP interface to loopback0.
>  
> Regards
>  
> Karen Cheng
> Voice Network Engineer
>  
>  
>  
> From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Bill Riley
> Sent: Friday, 12 November 2010 2:15 AM
> To: cisco-voip at puck.nether.net
> Subject: [cisco-voip] SIP trunk one way audio
>  
> I have a new SIP trunk terminating in a 2921 CUBE bundle. When I call in from the Trunk directly to an IP phone it works correctly. If I call from the trunk to IP phone and the IP phone transfers the call without waiting for the remote party to answer I get one way audio. From reading this looks like and MTP issue but I have an MTP set in the MRGL for the trunk.
> 
> 75% of inspected vehicle have a defect*. Call 13 1905 and book an RACQ Vehicle Inspection today. *Based on the RACQ Vehicle Defect Report January 2008
> 
> 
> Please Note: If you are not the intended recipient, please delete this email as its use is prohibited. RACQ does not warrant or represent that this email is free from viruses or defects. If you do not wish to receive any further commercial electronic messages from RACQ please e-mail unsubscribe at racq.com.au or contact RACQ on 13 19 05.
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>  
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>  
>  
>  

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20101115/b4efef64/attachment.html>