[cisco-voip] Upgrade from CUCM 7.1.2 to CUCM 7.1.(5b)

[Matthew Loraditch]

I have done that and you can just rerun it

Sent from my Android phone using TouchDown (www.nitrodesk.com)

-----Original Message-----
From: Jason Aarons (US) [jason.aarons at us.didata.com]
Received: 9/11/10 4:18 PM
To: Wes Sisk [wsisk at cisco.com]; Cheng, Karen [Karen.Cheng at racq.com.au]
CC: cisco-voip at puck.nether.net [cisco-voip at puck.nether.net]
Subject: Re: [cisco-voip] Upgrade from CUCM 7.1.2 to CUCM 7.1.(5b)

Say you upgrade from 7.1 to 7.5 but forget to switch partitions/reboot and remember 5 months later.  Is there a cancel command or can you re-do the upgrade?

From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Wes Sisk
Sent: Saturday, September 11, 2010 4:08 PM
To: Cheng, Karen
Cc: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Upgrade from CUCM 7.1.2 to CUCM 7.1.(5b)

That is correct. Database is migrated at upgrade time. Changes made after upgrade are lost.  You need a change freeze after upgrade and before switch version.
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/cucos/7_0_1/cucos/iptpch7.html#wp1040186
[cid:image001.gif at 01CB51CC.DE92C510]
________________________________

Note You can only make changes to the database on the active partition. The database on the inactive partition does not get updated. If you make changes to the database after an upgrade, you must repeat those changes after switching the partition.

/Wes


Cheng, Karen wrote:
Hmm I think I answered my own question.

Although system configuration gets ported over, database changes since the upgrade wont.

Regards

Karen Cheng
Voice Network Engineer



From: cisco-voip-bounces at puck.nether.net<mailto:cisco-voip-bounces at puck.nether.net> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Karen Cheng
Sent: Saturday, 11 September 2010 4:33 PM
To: cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
Subject: [cisco-voip] Upgrade from CUCM 7.1.2 to CUCM 7.1.(5b)

Hey guys,

Just wondering whether anyone has run into an issue where upgrading to CUCM 7.1.(5b) results in missing random data?

I upgraded both my lab and production servers and upon upgrade have lost SIP trunks, CTI Route Points, Device Pools and some phone settings such as headset hookswitch settings. As I had completed a backup beforehand I tried to restore it but those missing data bits did not get restored. I rolled back to 7.1.2 and all those settings are now there again.

The only thing I can think of is that I had installed the 7.1.5b in a staged install to the inactive partition over a 3 week period as I have 5 servers in the cluster. My understanding is that data on the active partition will automatically get migrated over to the inactive when the upgrade is performed.

This may be incorrect and if so is there a way to perform the upgrade and then sync the missing information?

Karen

Show Your RACQ Card & Save this September school holiday at AMF Bowling Centres, Alma Park Zoo and Aussie World! Visit www.racq.com.au/benefits<http://www.racq.com.au/benefits> for more discount holiday ideas.


Please Note: If you are not the intended recipient, please delete this email as its use is prohibited. RACQ does not warrant or represent that this email is free from viruses or defects. If you do not wish to receive any further commercial electronic messages from RACQ please e-mail unsubscribe at racq.com.au<mailto:unsubscribe at racq.com.au> or contact RACQ on 13 19 05.




________________________________



_______________________________________________

cisco-voip mailing list

cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>

https://puck.nether.net/mailman/listinfo/cisco-voip



________________________________

[http://image.exct.net/lib/feed16797d620d/i/2/0ede5e1b-f.gif]<http://www.dimensiondata.com/_layouts/forms.aspx?FormID=204>

Disclaimer: This e-mail communication and any attachments may contain confidential and privileged information and is for use by the designated addressee(s) named above only. If you are not the intended addressee, you are hereby notified that you have received this communication in error and that any use or reproduction of this email or its contents is strictly prohibited and may be unlawful. If you have received this communication in error, please notify us immediately by replying to this message and deleting it from your computer. Thank you.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100911/4756d45e/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.gif
Type: image/gif
Size: 1111 bytes
Desc: image001.gif
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100911/4756d45e/attachment.gif>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image002.png
Type: image/png
Size: 168 bytes
Desc: image002.png
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100911/4756d45e/attachment.png>