[cisco-voip] sending 999 calls via the FXO in both CUCM and SRST mode

[Ted Nugent]

Very much confussed as to what you're trying to accomplish now, perhap I'm
missing something? Your system is configured for MGCP judging from the
dialpeers? you either have an aggregate PRI bank for outbound calls or SIP
trunks or something and you want to use local FXO ports for 999? Is that
close? If that is correct then, as Nate mentioned, why not just create a
single 999 pattern pointing to the local RG which would contain the FXO
ports for that site... Yes that is 150 RGs but it will work? Perhaps I
missed something? If so please clarify.

On Thu, Aug 23, 2012 at 8:02 PM, abbas Wali <abbaseo at gmail.com> wrote:

> Thanks for that Nate, But I was under the impression that when a phone
> even though regestered with the Centralized CUCM, still realizing that for
> the 999 pattern there is a local dial peer which is under the H323 control
> and therefore he doesnt need to go to the CM.
>
> we have around 150 sites, which wil mean that we have to configure 150 RP
> on the CUCM for that. which is messy, veryyyy messy
>
>
> On 24 August 2012 00:27, Norton, Mike <mikenorton at pwsd76.ab.ca> wrote:
>
>>  Even if you were to manage to make the port be H.323, I’m not seeing
>> what that would accomplish. You’d still need to do something in CUCM in
>> order for CUCM to know to send the calls from certain phones to that
>> specific H.323 gateway.****
>>
>> ** **
>>
>> -- ****
>>
>> Mike Norton****
>>
>> I.T. Support****
>>
>> Peace Wapiti School Division No. 76****
>>
>> Helpdesk: 780-831-3080****
>>
>> Direct: 780-831-3076****
>>
>> ** **
>>
>> ** **
>>
>> *From:* cisco-voip-bounces at puck.nether.net [mailto:
>> cisco-voip-bounces at puck.nether.net] *On Behalf Of *abbas Wali
>> *Sent:* August-23-12 4:06 PM
>> *To:* Nate VanMaren
>>
>> *Cc:* cisco-voip at puck.nether.net
>> *Subject:* Re: [cisco-voip] sending 999 calls via the FXO in both CUCM
>> and SRST mode****
>>
>> ** **
>>
>> Scott, ****
>>
>> ** **
>>
>> we want not to get more hardware or providers on this. ****
>>
>> ** **
>>
>> I heard somewhere, that you can configure a Voice Gateway such that one
>> interface is controlled by MGCP another is H323 and so on. ****
>>
>> ** **
>>
>> so if I can somehow control that FXO on H323 then that can use the local
>> dial peers no matter what.****
>>
>> ** **
>>
>> So the million dollar questions becomes how to have this one FXO
>> interface controlled by an H323 in an MGCP gateway!!!!!!!!!****
>>
>> On 23 August 2012 21:19, Nate VanMaren <VanMarenNP at ldschurch.org> wrote:*
>> ***
>>
>> Local route group?****
>>
>>  ****
>>
>> *From:* cisco-voip-bounces at puck.nether.net [mailto:
>> cisco-voip-bounces at puck.nether.net] *On Behalf Of *Scott Voll
>> *Sent:* Thursday, August 23, 2012 2:10 PM
>> *To:* abbas Wali
>> *Cc:* cisco-voip at puck.nether.net
>> *Subject:* Re: [cisco-voip] sending 999 calls via the FXO in both CUCM
>> and SRST mode****
>>
>>  ****
>>
>> if you want an easier solution, use a sip e911 provider and let them
>> route it.****
>>
>>  ****
>>
>> otherwise yes, create a site_911 partition and add it to the site CSS
>> with a 911 RP in that site_911 partion.****
>>
>>  ****
>>
>> Scott****
>>
>> On Thu, Aug 23, 2012 at 12:47 PM, abbas Wali <abbaseo at gmail.com> wrote:**
>> **
>>
>>
>> ****
>>
>> Hi all,****
>>
>>  ****
>>
>> I have to configure an FXO line for 999 calls. ****
>>
>>  ****
>>
>> okay this works fine when i am in SRST mode and I have application global
>> alternate default ON with ****
>>
>>  ****
>>
>> dial-peer voice 999 pots****
>>
>> description EMERGENCY****
>>
>> destination-pattern 999****
>>
>> port 0/1/0****
>>
>> forward-digits all****
>>
>>  ****
>>
>> and for incoming calls****
>>
>>  ****
>>
>> voice-port 0/1/0****
>>
>> echo-cancel coverage 64****
>>
>> cptone GB****
>>
>> timing hookflash-out 50****
>>
>> connection plar opx 61234****
>>
>> impedance complex2****
>>
>>  ****
>>
>> where 61234 is an extension. ****
>>
>>  ****
>>
>> the only issue is when the CUCM comes back in that FXO re-registeres with
>> CUCM as****
>>
>>  ****
>>
>> dial-peer voice 999010 pots****
>>
>> preference 1****
>>
>> service MGCPAPP****
>>
>> port 0/1/0****
>>
>>  ****
>>
>> again incoming calls wil work fine as I have an Attendent DN configured.
>> but for the outgoing calls I only want it to use the local FXO ****
>>
>> (for the emergency services to trunup at the right location)****
>>
>>  ****
>>
>> I wonder if that can only be done in the CUCM as configuring local 999
>> route pattern and limiting the phones to use them in any case!!****
>>
>> we have alot of site and that will be alot of work on the CUCM. ****
>>
>>  ****
>>
>> isnt there a better way!!!!****
>>
>>  ****
>>
>>  ****
>>
>> thanks for the help****
>>
>>  ****
>>
>> A****
>>
>>
>> --
>> @bbas..
>>
>>
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip****
>>
>>  ****
>>
>>
>>
>> ****
>>
>> ** **
>>
>> --
>> @bbas.. ****
>>
>
>
>
> --
> @bbas..
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20120823/baa89346/attachment.html>