[cisco-voip] upgrade during install from 9.0 to 9.1

Wed Jan 2 16:34:00 EST 2013

Well that's good, I can just put a PUT order in edelivery and get it. Let's see if it works.

Matthew G. Loraditch - CCNP-Voice, CCNA, CCDA

1965 Greenspring Drive
Timonium, MD 21093

voice. 410.252.8830
fax.  410.252.9284

Twitter<http://twitter.com/heliontech>  |  Facebook<http://www.facebook.com/#!/pages/Helion/252157915296>  | Website<http://www.heliontechnologies.com/>  |  Email Support<mailto:support at heliontechnologies.com?subject=Technical%20Support%20Request>

From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Ryan Ratliff
Sent: Wednesday, January 02, 2013 4:22 PM
To: Tim Frazee
Cc: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] upgrade during install from 9.0 to 9.1

I was told this restriction was added around 8.5 but I'm still waiting on some other folks to comment.

To get to 9.1 you either do a fresh install or you upgrade, same as any other version.  I understand the release of 9.1 has immediately replaced 9.0 on new 9.x orders (much like 8.6 did for 8.5) so any 9.x media kit ordered today will be sent 9.1 bootable media.

-Ryan

On Jan 2, 2013, at 4:12 PM, Tim Frazee <tfrazee at gmail.com<mailto:tfrazee at gmail.com>> wrote:

I could see that.

But tell that to my 8.5 upgrade from an 8.0 boot disk I was able to do back in the day......

In short, you say that the only way currently to get to 9.1 is upgrade from an already installed support version, not during the install process.

for the record and I know its not supported, I did try the hack of grabbing the boot info file from 9.0 and pushing it into the 9.1 iso. The install process failed post installing everything.

Thanks for digging Ryan.

On Wed, Jan 2, 2013 at 12:21 PM, Ryan Ratliff <rratliff at cisco.com<mailto:rratliff at cisco.com>> wrote:
Confirmed I see it here in the lab and it looks to be intentional, though I'm still digging.
Initial word is for a while now upgrade-during-install is only supported to the same major/minor version.

Anything beyond that requires a separate upgrade after install.

-Ryan

On Jan 2, 2013, at 11:18 AM, Tim Frazee <tfrazee at gmail.com<mailto:tfrazee at gmail.com>> wrote:

I did just that. after I tried with the pre-release, I used my NFR iso. Same result.

I only used the pre-release because it was already on my datastore and i was feeling a bit lazy over vacation. After I attempted the same procedure with 9.0(1) -37 iso, I received the exact same error.

Ryan, should I be able to boot off of 9.0 and upgrade-during-install with 9.1?
On Wed, Jan 2, 2013 at 9:47 AM, Ryan Ratliff <rratliff at cisco.com<mailto:rratliff at cisco.com>> wrote:
9.0.0.99101-22<tel:9.0.0.99101-22> is not a 9.0 ES, it's a pre-release build of 9.1.  Throw it in the trash and try with a real 9.0 build (I'm going to start this now).

-Ryan

On Jan 2, 2013, at 9:50 AM, Tim Frazee <tfrazee at gmail.com<mailto:tfrazee at gmail.com>> wrote:

I didnt test to see if the 9.1 from CCO is bootable. In the past they havent been.

attached is a screenshoot of the error I received when I tried to feed the 9.1 via CCO during a booted-from-nfr9.0 media
On Mon, Dec 31, 2012 at 5:02 PM, Nate VanMaren <VanMarenNP at ldschurch.org<mailto:VanMarenNP at ldschurch.org>> wrote:
I had lots of problems doing upgrade during installs with 9.0 ESs.  The ESs are usually bootable so I just gave up and installed fresh.  Is the 9.1 download bootable?

From: cisco-voip-bounces at puck.nether.net<mailto:cisco-voip-bounces at puck.nether.net> [mailto:cisco-voip-bounces at puck.nether.net<mailto:cisco-voip-bounces at puck.nether.net>] On Behalf Of Tim Frazee
Sent: Monday, December 31, 2012 3:50 PM
To: cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
Subject: Re: [cisco-voip] upgrade during install from 9.0 to 9.1

This was for UCM and Unity Connection. didnt try anything else.

On Mon, Dec 31, 2012 at 1:04 PM, Tim Frazee <tfrazee at gmail.com<mailto:tfrazee at gmail.com>> wrote:
I have the 9.0 NFR and the 9.1 upgrade iso pulled from CCO.

I'm getting an error if I feed the 9.1 iso to the 9.0 install process that i want to upgrade during the install process. I've been able to do this many times in the past with never a problem like this.

Anyone have any ideas?

NOTICE: This email message is for the sole use of the intended recipient(s) and may contain confidential and privileged information. Any unauthorized review, use, disclosure or distribution is prohibited. If you are not the intended recipient, please contact the sender by reply email and destroy all copies of the original message.

<temp.png>_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
https://puck.nether.net/mailman/listinfo/cisco-voip

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20130102/527d4a29/attachment.html>