[cisco-voip] ISR 4431 - Need to configure "clock source internal" on PRI interface , get error

[Russell Chaseling]

Hi,

Did you ever get to the bottom of this?

I’m having same issue trying to be the Master on a 4331 integrating with a Nortel Cs1000

Thanks
Russell

From: cisco-voip [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Brian V
Sent: 28 October 2015 01:46
To: NateCCIE <nateccie at gmail.com>
Cc: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] ISR 4431 - Need to configure "clock source internal" on PRI interface , get error

I've opened a TAC case on it.  I'll report back what I find out.

On Tue, Oct 27, 2015 at 8:43 PM, NateCCIE <nateccie at gmail.com<mailto:nateccie at gmail.com>> wrote:
Ryan,

This doc and sample config seems to only show how to do normal user side & network clocking.

When doing network side isdn to a pbx, you have to provide them the clock, I like Brian have not figured out that part of the 4K voodoo.

Sent from my iPhone

On Oct 27, 2015, at 7:23 PM, Ryan Huff <ryanhuff at outlook.com<mailto:ryanhuff at outlook.com>> wrote:
Brian,

You'll essentially be doing the same thing as you would have in the ISRG2 but as you've discovered, the syntax has changed a bit in the 4k's. I've included the relevant portion of a t1 config on a 4k in my lab below. Here is the link for 4th gen NIM t1 configurations (I'd suggest a good read here, a lot of syntax has changed that might leave you scratching your head): http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/NIM/software/configuration/guide/ConfT1E1NIM.html





Hope This Helps,



Ryan



|----- CONFIG SAMPLE -----|



card type t1 0 2
!
isdn switch-type primary-ni
!
network-clock synchronization automatic
network-clock synchronization participate 0/2
!
voice-card 0/2
dsp services dspfarm
!
controller T1 0/2/0
framing esf
linecode b8zs
!

clock source line primary

network-clock input-source 1 controller t1 0/2/0
cablelength long 0db
pri-group timeslots 1-24 voice-dsp
!
interface Serial0/2/0:23
encapsulation hdlc
isdn switch-type primary-ni
no cdp enable

!



|----- CONFIG SAMPLE -----|

________________________________
From: cisco-voip <cisco-voip-bounces at puck.nether.net<mailto:cisco-voip-bounces at puck.nether.net>> on behalf of Brian V <bvanbens at gmail.com<mailto:bvanbens at gmail.com>>
Sent: Tuesday, October 27, 2015 8:42 PM
To: cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
Subject: [cisco-voip] ISR 4431 - Need to configure "clock source internal" on PRI interface , get error


I have a ISR 4331 that I'm configuring for voice PRI support.

Performing an integration with a Nortel PBX (back to back PRI) where i need to be the clock source on the underlying T1 circuit.



In the past on ISR G2 platforms (like a 2921),  I could configure "clock source internal" under the controller T1 interface.  On the 4331 I get the following error when the clock source it set to internal under the controller T1



TIV-4331-01-TEMP(config-controller)#pri-group timeslots 1-24

%Cannot create ds0/tdm/pri-group with clock source internal

%pri-group voice-dsp cannot be created under the clock source configuration



How do I accomplish the same on this newer platform or is it no longer possible ?



The NIM does have it's own DSP resources.

I can get the integration up and working, with the default "clock source line",  but I  get slips on the t1 as the Nortel side is free running  and looking to the line as a clock source on its end.



I hope I'm just missing something obvious.

Thanks




_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
https://puck.nether.net/mailman/listinfo/cisco-voip

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20161005/32aa6962/attachment.html>