[cisco-voip] 8832s

Sun Jun 10 10:54:47 EDT 2018

I would only deploy a device pack on new cluster build.  All else per device update.  I used to like to hardcode the load field on a per phone basis to prevent them from changing.  Been doing less of that.

The cmterm CE (Collaboration Endpoint) loads of 1.8GB are ridiculous, in DRS .tar backups too.

From: cisco-voip [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Anthony Holloway
Sent: Monday, April 30, 2018 9:07 AM
To: Charles Goldsmith <wokka at justfamily.org>
Cc: cisco-voip (cisco-voip at puck.nether.net) <cisco-voip at puck.nether.net>
Subject: Re: [cisco-voip] 8832s

I wish CUCM didn't ship with newer phone firmware.

Since Cisco already drops support for all firmware older than the most recent firmware:

- For each IP Phone model, once Cisco releases a new firmware version, the older versions are no longer supported.
- Cisco expects customers who encounter a problem on an older version of firmware to test the latest firmware on a subset of phones in order to confirm that the problem still exists.
Source: http://www.cisco.com/c/en/us/support/docs/collaboration-endpoints/unified-ip-phone-7900-series/116684-technote-ipphone-00.html<http://www.cisco.com/c/en/us/support/docs/collaboration-endpoints/unified-ip-phone-7900-series/116684-technote-ipphone-00.html>

And most people agree that you should upgrade firmware before a CUCM upgrade anyway, just remove firmware from CUCM.

Not too mention it clutters up TFTP.

I also think that the firmware should be decoupled from the Device Packs.  When adding support for a single model phone, rarely am I also trying to upgrade 100% of the phones in the environment too.

On Sun, Apr 29, 2018 at 8:22 PM Charles Goldsmith <wokka at justfamily.org<mailto:wokka at justfamily.org>> wrote:
Since the 8832 is a dual bank phone, shouldn't it have the old image on it in the backup bank?  Maybe hardcoding the old image on the phone configuration and doing a reset will cause it to boot from it?

On Sun, Apr 29, 2018 at 7:06 PM Ryan Huff <ryanhuff at outlook.com<mailto:ryanhuff at outlook.com>> wrote:
Sounds like the ole’ ‘step upgrade’ issue that plagued the 79xx series back in the 8.x days ....

My guess is they don’t actually need RMA’ed, just the easiest way to deal with it ....

I’d flash the phones and advertise an isolated tftp server to them with the firmware load and XML bootstrap file. The phones aren’t working now, so flashing them and then still not getting them to load right isn’t going to make it any worse.

Use DNS in the DHCP scope in your isolation network with the TFTP server and pcap/debug the DNS queries to see the bootstrap and load files it’s looking for.

In the 79xx series back in the day when I would perform this Lazarus trick for some lucky customers; the bootstrap filename was XMLDefault.cnf.xml. Not sure if it’s the same nowadays though.

Here is the Cisco doc on the procedure for the older stuff .... worth a shot but not sure if it still works on the newer gear.

https://www.cisco.com/c/en/us/support/docs/unified-communications/unified-communications-manager-callmanager/200582-Update-Cisco-IP-Phone-Firmware-through-T.html<https://www.cisco.com/c/en/us/support/docs/unified-communications/unified-communications-manager-callmanager/200582-Update-Cisco-IP-Phone-Firmware-through-T.html>

-Ryan-

On Apr 29, 2018, at 18:53, Jason Aarons (Americas) <jason.aarons at dimensiondata.com<mailto:jason.aarons at dimensiondata.com>> wrote:

I have a customer with four 8832 conference room phones. Their CUCM was running version 12.0.1 of the 8832 firmware. These phones shipped with version 12.0.1SR2. When they registered the first two phones they downgraded from 12.0.1SR2 to 12.0.1 and are now unusable. They sit on “Connecting” after booting up. They do not get an IP address. You cannot set an IP address manually. If you reset the phone it doesn’t fix it, nor does a factory reset<https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cuipph/8832/english/adminguide/cs88_b_conference-8832-admin-guide-cucm/cs88_b_conference-8832-admin-guide-cucm_chapter_01011.html> allow the phone to revert to the firmware they shipped with. Cisco TAC says they must be RMA’d. We upgraded CUCM to 12.0.1SR3 and the other two phones upgraded fine from 12.0.1SR2 to 12.0.1SR3.

Does anyone have any ideas on what we could do to fix these phones other than RMAing them?

Get Outlook for Android<https://aka.ms/ghei36>

This email and all contents are subject to the following disclaimer:
"http://www.dimensiondata.com/emaildisclaimer"<http://www.dimensiondata.com/Global/Policies/Pages/Email-Disclaimer.aspx>
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
https://puck.nether.net/mailman/listinfo/cisco-voip<https://puck.nether.net/mailman/listinfo/cisco-voip>
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
https://puck.nether.net/mailman/listinfo/cisco-voip<https://puck.nether.net/mailman/listinfo/cisco-voip>
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
https://puck.nether.net/mailman/listinfo/cisco-voip<https://puck.nether.net/mailman/listinfo/cisco-voip>

itevomcid
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20180610/d9fb4564/attachment.html>