[cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

Hamu Ebiso hebiso2010 at hotmail.com
Thu Mar 1 11:06:36 EST 2018


Hi Anthony,


yes the call was hitting the gateway because I was seeing FXO port going Off-Hook. The problem was that Logging was not setup in the gateway. After I setup the Logging, I'm now seeing logs.


I have attached the log.

thanks

Hamu

________________________________
From: avholloway at gmail.com <avholloway at gmail.com> on behalf of Anthony Holloway <avholloway+cisco-voip at gmail.com>
Sent: Thursday, March 1, 2018 8:45 AM
To: Hamu Ebiso
Cc: Cisco VoIP Group
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

Since you didn't see the call in your debugs, your call likely didn't hit your gateway.

Can you confirm how you made your test call, when you had your debug running?

On Feb 28, 2018 2:46 PM, "Hamu Ebiso" <hebiso2010 at hotmail.com<mailto:hebiso2010 at hotmail.com>> wrote:

Here is the dial-peer output

1#show run | sec dial-peer
dial-peer voice 1 pots
 trunkgroup FXO_EM
 translation-profile incoming Inbound
 call-block translation-profile incoming block_profile
 call-block disconnect-cause incoming call-reject
 incoming called-number .
 direct-inward-dial
dial-peer voice 911 pots
 trunkgroup FXO_EM
 description Services
 translation-profile outgoing Strip9
 destination-pattern 911
dial-peer voice 9911 pots
 trunkgroup FXO_EM
 description Services
 translation-profile outgoing Strip9
 destination-pattern 9911
dial-peer voice 2 voip
 description CUCM Dial-Peer - Inbound
 preference 1
 destination-pattern 12086858038<tel:(208)%20685-8038>
 session protocol sipv2
 session target ipv4:10.0.2.6
 incoming uri via 10
 voice-class codec 1
 dtmf-relay rtp-nte sip-kpml
 fax-relay ecm disable
 fax nsf 000000
 ip qos dscp cs3 signaling
 no vad
dial-peer voice 3 voip
 preference 2
 destination-pattern 12086858038<tel:(208)%20685-8038>
 session target ipv4:10.0.2.3
dial-peer voice 650 pots
 trunkgroup Local
 description Local outbound
 translation-profile outgoing Strip9
 destination-pattern 9208.......
dial-peer voice 4 pots
 trunkgroup FXO_EM
 description ** 10-digit Local Call **
 translation-profile outgoing Strip9
 destination-pattern ^9[2-9]..[2-9]......$
 forward-digits 10
dial-peer voice 5 voip
 description FXO test
 destination-pattern 12083437020<tel:(208)%20343-7020>
 session target ipv4:10.0.2.5


thank you very much!!

________________________________
From: Anthony Holloway <avholloway+cisco-voip at gmail.com<mailto:avholloway%2Bcisco-voip at gmail.com>>
Sent: Wednesday, February 28, 2018 1:29 PM
To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

Maybe you're actually using MGCP then?  You still haven't shown the dial-peers on the gateway.  Is that because you don't have any?

show run | section dial-peer

On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso <hebiso2010 at hotmail.com<mailto:hebiso2010 at hotmail.com>> wrote:

debug was turned on as shown below.


1#debug voice ccapi inout
voip ccapi inout debugging is on

made test calls and then show log, I see below output.

1#show log
Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)

No Active Message Discriminator.


No Inactive Message Discriminator.

    Console logging: level debugging, 517 messages logged, xml disabled,
                     filtering disabled
    Monitor logging: level debugging, 0 messages logged, xml disabled,
                     filtering disabled
    Buffer logging:  level debugging, 550 messages logged, xml disabled,
                    filtering disabled
    Exception Logging: size (4096 bytes)
    Count and timestamp logging messages: disabled
    Persistent logging: disabled

No active filter modules.

    Trap logging: level debugging, 620 message lines logged
        Logging to 10.0.7.139  (udp port 514, audit disabled,
              link up),
              435 message lines logged,
              0 message lines rate-limited,
              0 message lines dropped-by-MD,
              xml disabled, sequence number disabled
              filtering disabled
        Logging to 10.0.8.12  (udp port 514, audit disabled,
              link up),
              435 message lines logged,
              0 message lines rate-limited,
              0 message lines dropped-by-MD,
              xml disabled, sequence number disabled
              filtering disabled
        Logging Source-Interface:       VRF Name:
        Loopback0


I don't see any calls activity.


thanks


________________________________
From: Anthony Holloway <avholloway+cisco-voip at gmail.com<mailto:avholloway%2Bcisco-voip at gmail.com>>
Sent: Wednesday, February 28, 2018 11:19 AM

To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router
But you didn't send all the information, because your output doesn't show the dial-peers.

One method is to capture the output from "debug voip ccapi inout" and look for the following line "Outgoing Dial-peer="

You also didn't address the regions either.  Can you send that too?

On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso <hebiso2010 at hotmail.com<mailto:hebiso2010 at hotmail.com>> wrote:

I was just trying to give you all the information so that you will be able to see the whole picture.

Regarding your questions, I don't know how to check that.


________________________________
From: Anthony Holloway <avholloway+cisco-voip at gmail.com<mailto:avholloway%2Bcisco-voip at gmail.com>>
Sent: Wednesday, February 28, 2018 10:45 AM

To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router
That's interesting that I asked for the dial-peer config, and you sent everything but.

Do you know how to confirm which dial-peer the gateway is using?

On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso <hebiso2010 at hotmail.com<mailto:hebiso2010 at hotmail.com>> wrote:

Below is gateway configuration




isdn switch-type primary-ni
!
!
trunk group FXO_EM
 hunt-scheme sequential
 translation-profile incoming Incoming
!
!
trunk group Local
 hunt-scheme sequential
 translation-profile outgoing outbound
!
!
trunk group LD
 translation-profile outgoing outbound
!
voice-card 0
 dspfarm
 dsp services dspfarm
!
!
voice call send-alert
voice rtp send-recv
!
voice service voip
 ip address trusted list
  ipv4 10.170.99.12
  ipv4 10.44.50.14
  ipv4 10.44.50.39
 no ip address trusted authenticate
 clid substitute name
 clid network-provided
 allow-connections h323 to h323
 allow-connections h323 to sip
 allow-connections sip to h323
 allow-connections sip to sip
 redirect ip2ip
 signaling forward unconditional
 fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
 no fax-relay sg3-to-g3
 modem passthrough nse codec g711ulaw
 sip
  bind control source-interface Loopback0
  bind media source-interface Loopback0
  session transport tcp
  min-se 360 session-expires 360
  ds0-num
  header-passing
  error-passthru
  registrar server expires max 600 min 60
  early-offer forced
  midcall-signaling passthru
  no call service stop
!
!
voice class uri 10 sip
 host ipv4:10.x.x.x
 host ipv4:10..x.x.x
 host ipv4:10..x.x.x
voice class codec 1
 codec preference 1 g711ulaw
 codec preference 2 g729r8
!
voice class codec 2
 codec preference 1 g711ulaw
!
!
!
!
voice translation-rule 1
 rule 1 /^208343\(....\)$/ /1208343\1/
!
voice translation-rule 9
 rule 1 /5.../ /1208343\0/
!
voice translation-rule 10
 rule 1 /^911/ /911/
 rule 2 /^9911/ /911/
!
voice translation-rule 15
!
voice translation-rule 30
 rule 1 /^911/ /911/
 rule 2 /^9911/ /911/
 rule 4 /^9\(011.*\)/ /\1/
 rule 9 /^9\(.*\)/ /\1/
!
!
voice translation-profile Add1
 translate calling 91
 translate called 1
!
voice translation-profile Inbound
 translate called 1
!
voice translation-profile Strip9
 translate called 10
!
voice translation-profile block_profile
 translate calling 15
!
voice translation-profile outbound
 translate calling 10
!
!
crypto pki token default removal timeout 0
!
!
!
!
license udi pid CISCO3845-MB sn FOC123128X5
license accept end user agreement
archive
 log config
  hidekeys
username admin privilege 15 password 7 105D1F0C
username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx.
!
!
controller T1 0/0/0
 shutdown
 cablelength long 0db
!
controller T1 0/1/0
 shutdown
 cablelength long 0db
!
!
!
!
!
!
interface Loopback0
 ip address 10.x.x.x 255.255.255.128
!
interface GigabitEthernet0/0
 description uplink to Lan1
 ip address 10.x.x.x 255.255.255.252
 duplex auto
 speed auto
 media-type rj45
!
interface GigabitEthernet0/1
 description uplink to Lan2
 ip address 10.x.x.x 255.255.255.252
 duplex auto
 speed auto
 media-type rj45
!
router ospf 1
 auto-cost reference-bandwidth 10000
 network 10.0.0.0 0.0.255.255 area 10.0.0.0
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20180301/657168de/attachment.html>
-------------- next part --------------
An embedded and charset-unspecified text was scrubbed...
Name: Debug.txt
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20180301/657168de/attachment.txt>


More information about the cisco-voip mailing list