[cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router
Anthony Holloway
avholloway+cisco-voip at gmail.com
Fri Mar 2 10:07:14 EST 2018
Unfortunately, again, the number you're calling 4131, is not matching the
dial-peers you posted; however, the debugs are still saying you're hitting
DP 5, which is an H323 DP not SIP.
On Thu, Mar 1, 2018 at 1:44 PM Hamu Ebiso <hebiso2010 at hotmail.com> wrote:
>
> Here is the debug output for debug voip ccapi inout, and debug ccsip
> messages.
>
>
> Thank you again for your help.
>
>
>
>
> ------------------------------
> *From:* Anthony Holloway <avholloway+cisco-voip at gmail.com>
> *Sent:* Thursday, March 1, 2018 1:16 PM
> *To:* Hamu Ebiso
>
> *Cc:* Cisco VoIP Group
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> debug voip ccapi inout, and if you're using SIP, then debug ccsip messages
> as well. the debug vpm signal is not very helpful, though it does show the
> port selected.
>
> On Thu, Mar 1, 2018 at 1:05 PM Hamu Ebiso <hebiso2010 at hotmail.com> wrote:
>
> Thank you Anthony very much for your help.
>
> The 19529473283 <(952)%20947-3283> for connection plar 19529473283
> <(952)%20947-3283> I was testing with. After changing of few things on
> the gateway, I'm now seeing different messages when I run debug. The calls
> used to ring only one time and then fast busy, now it rings twice and then
> fax busy for incoming. for outgoing, it's says calls connot be completed as
> dialed.
>
>
> Attached the new logs again. I really appreciate your help.
>
>
> thanks again.
>
> Hamu
>
>
> ------------------------------
> *From:* Anthony Holloway <avholloway+cisco-voip at gmail.com>
> *Sent:* Thursday, March 1, 2018 11:05 AM
>
> *To:* Hamu Ebiso
> *Cc:* Cisco VoIP Group
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> According to the debug, you're calling 19529473283 <(952)%20947-3283>.
> Is that correct?
>
> Called Number=19529473283 <(952)%20947-3283>(TON=Unknown, NPI=Unknown),
>
>
> If so, then this debug is not for this gateway, because you're hitting
> Outgoing Dial-peer=5
>
> Outgoing Dial-peer=5, Params=0x688FF3FC, Progress Indication=ORIGINATING SIDE IS NON ISDN(3)
>
>
> And dial-peer 5, while it exists in your config you pasted, it doesn't
> match the called number.
>
> dial-peer voice 5 voip
> description FXO test
> destination-pattern 12083437020 <(208)%20343-7020>
> session target ipv4:10.0.2.5
> !
>
> Even if it did match the destination pattern, you're missing some config
> on this dial-peer to make a SIP capable dial-peer, which means it's sending
> H323 setup to CUCM. If you built the gateway as H323, then I can see how
> it rang your CIPC, otherwise, if you built it as SIP, which you said you
> did, then it would never ring your CIPC.
>
> So, something is not adding up here.
>
> Also, you're hitting Incoming Dial-peer=0, which on a POTS leg is not too
> terrible, but it's also not good practice to be using dial-peer 0. It's
> really VoIP DP 0 that is messy though.
>
> Incoming Dial-peer=0, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), Calling IE Present=FALSE,
>
>
>
> On Thu, Mar 1, 2018 at 10:06 AM Hamu Ebiso <hebiso2010 at hotmail.com> wrote:
>
> Hi Anthony,
>
>
> yes the call was hitting the gateway because I was seeing FXO port going
> Off-Hook. The problem was that Logging was not setup in the gateway. After
> I setup the Logging, I'm now seeing logs.
>
>
> I have attached the log.
>
>
> thanks
>
> Hamu
> ------------------------------
> *From:* avholloway at gmail.com <avholloway at gmail.com> on behalf of Anthony
> Holloway <avholloway+cisco-voip at gmail.com>
> *Sent:* Thursday, March 1, 2018 8:45 AM
> *To:* Hamu Ebiso
> *Cc:* Cisco VoIP Group
>
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> Since you didn't see the call in your debugs, your call likely didn't hit
> your gateway.
>
> Can you confirm how you made your test call, when you had your debug
> running?
>
> On Feb 28, 2018 2:46 PM, "Hamu Ebiso" <hebiso2010 at hotmail.com> wrote:
>
> Here is the dial-peer output
>
> 1#show run | sec dial-peer
> dial-peer voice 1 pots
> trunkgroup FXO_EM
> translation-profile incoming Inbound
> call-block translation-profile incoming block_profile
> call-block disconnect-cause incoming call-reject
> incoming called-number .
> direct-inward-dial
> dial-peer voice 911 pots
> trunkgroup FXO_EM
> description Services
> translation-profile outgoing Strip9
> destination-pattern 911
> dial-peer voice 9911 pots
> trunkgroup FXO_EM
> description Services
> translation-profile outgoing Strip9
> destination-pattern 9911
> dial-peer voice 2 voip
> description CUCM Dial-Peer - Inbound
> preference 1
> destination-pattern 12086858038 <(208)%20685-8038>
> session protocol sipv2
> session target ipv4:10.0.2.6
> incoming uri via 10
> voice-class codec 1
> dtmf-relay rtp-nte sip-kpml
> fax-relay ecm disable
> fax nsf 000000
> ip qos dscp cs3 signaling
> no vad
> dial-peer voice 3 voip
> preference 2
> destination-pattern 12086858038 <(208)%20685-8038>
> session target ipv4:10.0.2.3
> dial-peer voice 650 pots
> trunkgroup Local
> description Local outbound
> translation-profile outgoing Strip9
> destination-pattern 9208.......
> dial-peer voice 4 pots
> trunkgroup FXO_EM
> description ** 10-digit Local Call **
> translation-profile outgoing Strip9
> destination-pattern ^9[2-9]..[2-9]......$
> forward-digits 10
> dial-peer voice 5 voip
> description FXO test
> destination-pattern 12083437020 <(208)%20343-7020>
> session target ipv4:10.0.2.5
>
>
> thank you very much!!
>
> ------------------------------
> *From:* Anthony Holloway <avholloway+cisco-voip at gmail.com>
> *Sent:* Wednesday, February 28, 2018 1:29 PM
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
>
> Maybe you're actually using MGCP then? You still haven't shown the
> dial-peers on the gateway. Is that because you don't have any?
>
> show run | section dial-peer
>
> On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso <hebiso2010 at hotmail.com>
> wrote:
>
> debug was turned on as shown below.
>
>
> 1#debug voice ccapi inout
> voip ccapi inout debugging is on
>
> made test calls and then show log, I see below output.
>
> 1#show log
> Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0
> flushes, 0 overruns, xml disabled, filtering disabled)
>
> No Active Message Discriminator.
>
>
> No Inactive Message Discriminator.
>
>
> Console logging: level debugging, 517 messages logged, xml disabled,
> filtering disabled
> Monitor logging: level debugging, 0 messages logged, xml disabled,
> filtering disabled
> Buffer logging: level debugging, 550 messages logged, xml disabled,
> filtering disabled
> Exception Logging: size (4096 bytes)
> Count and timestamp logging messages: disabled
> Persistent logging: disabled
>
> No active filter modules.
>
> Trap logging: level debugging, 620 message lines logged
> Logging to 10.0.7.139 (udp port 514, audit disabled,
> link up),
> 435 message lines logged,
> 0 message lines rate-limited,
> 0 message lines dropped-by-MD,
> xml disabled, sequence number disabled
> filtering disabled
> Logging to 10.0.8.12 (udp port 514, audit disabled,
> link up),
> 435 message lines logged,
> 0 message lines rate-limited,
> 0 message lines dropped-by-MD,
> xml disabled, sequence number disabled
> filtering disabled
> Logging Source-Interface: VRF Name:
> Loopback0
>
>
> I don't see any calls activity.
>
>
> thanks
>
> ------------------------------
> *From:* Anthony Holloway <avholloway+cisco-voip at gmail.com>
> *Sent:* Wednesday, February 28, 2018 11:19 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> But you didn't send all the information, because your output doesn't show
> the dial-peers.
>
> One method is to capture the output from "debug voip ccapi inout" and look
> for the following line "Outgoing Dial-peer="
>
> You also didn't address the regions either. Can you send that too?
>
> On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso <hebiso2010 at hotmail.com>
> wrote:
>
> I was just trying to give you all the information so that you will be able
> to see the whole picture.
>
> Regarding your questions, I don't know how to check that.
>
>
> ------------------------------
> *From:* Anthony Holloway <avholloway+cisco-voip at gmail.com>
> *Sent:* Wednesday, February 28, 2018 10:45 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> That's interesting that I asked for the dial-peer config, and you sent
> everything but.
>
> Do you know how to confirm which dial-peer the gateway is using?
>
> On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso <hebiso2010 at hotmail.com>
> wrote:
>
> Below is gateway configuration
>
>
>
>
> isdn switch-type primary-ni
> !
> !
> trunk group FXO_EM
> hunt-scheme sequential
> translation-profile incoming Incoming
> !
> !
> trunk group Local
> hunt-scheme sequential
> translation-profile outgoing outbound
> !
> !
> trunk group LD
> translation-profile outgoing outbound
> !
> voice-card 0
> dspfarm
> dsp services dspfarm
> !
> !
> voice call send-alert
> voice rtp send-recv
> !
> voice service voip
> ip address trusted list
> ipv4 10.170.99.12
> ipv4 10.44.50.14
> ipv4 10.44.50.39
> no ip address trusted authenticate
> clid substitute name
> clid network-provided
> allow-connections h323 to h323
> allow-connections h323 to sip
> allow-connections sip to h323
> allow-connections sip to sip
> redirect ip2ip
> signaling forward unconditional
> fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0
> fallback pass-through g711ulaw
> no fax-relay sg3-to-g3
> modem passthrough nse codec g711ulaw
> sip
> bind control source-interface Loopback0
> bind media source-interface Loopback0
> session transport tcp
> min-se 360 session-expires 360
> ds0-num
> header-passing
> error-passthru
> registrar server expires max 600 min 60
> early-offer forced
> midcall-signaling passthru
> no call service stop
> !
> !
> voice class uri 10 sip
> host ipv4:10.x.x.x
> host ipv4:10..x.x.x
> host ipv4:10..x.x.x
> voice class codec 1
> codec preference 1 g711ulaw
> codec preference 2 g729r8
> !
> voice class codec 2
> codec preference 1 g711ulaw
> !
> !
> !
> !
> voice translation-rule 1
> rule 1 /^208343\(....\)$/ /1208343\1/
> !
> voice translation-rule 9
> rule 1 /5.../ /1208343\0/
> !
> voice translation-rule 10
> rule 1 /^911/ /911/
> rule 2 /^9911/ /911/
> !
> voice translation-rule 15
> !
> voice translation-rule 30
> rule 1 /^911/ /911/
> rule 2 /^9911/ /911/
> rule 4 /^9\(011.*\)/ /\1/
> rule 9 /^9\(.*\)/ /\1/
> !
> !
> voice translation-profile Add1
> translate calling 91
> translate called 1
> !
> voice translation-profile Inbound
> translate called 1
> !
> voice translation-profile Strip9
> translate called 10
> !
> voice translation-profile block_profile
> translate calling 15
> !
> voice translation-profile outbound
> translate calling 10
> !
> !
> crypto pki token default removal timeout 0
> !
> !
> !
> !
> license udi pid CISCO3845-MB sn FOC123128X5
> license accept end user agreement
> archive
> log config
> hidekeys
> username admin privilege 15 password 7 105D1F0C
> username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx.
> !
> !
> controller T1 0/0/0
> shutdown
> cablelength long 0db
> !
> controller T1 0/1/0
> shutdown
> cablelength long 0db
> !
> !
> !
> !
> !
> !
> interface Loopback0
> ip address 10.x.x.x 255.255.255.128
> !
> interface GigabitEthernet0/0
> description uplink to Lan1
> ip address 10.x.x.x 255.255.255.252
> duplex auto
> speed auto
> media-type rj45
> !
> interface GigabitEthernet0/1
> description uplink to Lan2
> ip address 10.x.x.x 255.255.255.252
> duplex auto
> speed auto
> media-type rj45
> !
> router ospf 1
> auto-cost reference-bandwidth 10000
> network 10.0.0.0 0.0.255.255 area 10.0.0.0
> !
> ip forward-protocol nd
> !
> !
> no ip http server
> no ip http secure-server
> !
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20180302/40d670e2/attachment.html>
More information about the cisco-voip
mailing list