<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD><TITLE></TITLE>
<META http-equiv=Content-Type content="text/html; charset=us-ascii">
<META content="MSHTML 6.00.2800.1400" name=GENERATOR></HEAD>
<BODY text=#000000 bgColor=#ffffff>
<DIV dir=ltr align=left><SPAN class=047060304-10092005><FONT face=Arial
color=#0000ff size=2>Wes, you are correct. Simply pointing dial peers at
the opposite router will work. I've done this numerous times with great
success.</FONT></SPAN></DIV><BR>
<DIV class=OutlookMessageHeader lang=en-us dir=ltr align=left>
<HR tabIndex=-1>
<FONT face=Tahoma size=2><B>From:</B> cisco-voip-bounces@puck.nether.net
[mailto:cisco-voip-bounces@puck.nether.net] <B>On Behalf Of </B>Wes
Sisk<BR><B>Sent:</B> Friday, September 09, 2005 5:47 PM<BR><B>To:</B> Ruttman,
Peter G.<BR><B>Cc:</B> cisco-voip@puck.nether.net<BR><B>Subject:</B> Re:
[cisco-voip] Using another router's PRI while in SRST<BR></FONT><BR></DIV>
<DIV></DIV>configure both routers for SRST so router #2 will take over
management of the d-channel when MGCP backhaul to CM goes down.<BR><BR>Then
configure router #1 with an SRST VOIP dial-peer pointing to router#2. do a
normal huntgoup (preference 1, pref 2,).<BR><BR>believe this should work
fine.<BR><BR>/Wes<BR><BR>Ruttman, Peter G. wrote:
<BLOCKQUOTE
cite=mid7E3064B7EFC16C41B185C41D141008B75C5E0B@foleyex97.foleylaw.com
type="cite">
<META content="MS Exchange Server version 6.5.7226.0" name=Generator><!-- Converted from text/rtf format -->
<P><FONT face=Arial>I am looking to split my router's PRIs between two 3745
routers. So if I loose a router I will still continue to have PSTN
service without technical intervention. However, if my WAN goes into
SRST (the callmanagers are offsite) then the phones will register to only one
of the routers and I do not know how or if it is possible to configure SRST to
access the other router PRI. One way is to make two device pool and
point each at a different router and configure SRST on both but that doesn't
give me any redundancy if I also loose a PRI for some reason. Is there
any way for a signal SRST router to be configured to remotely get at another
router's PRIs?</FONT></P>
<P><FONT face=Arial>Pete</FONT> </P><BR>The preceding email message may be
confidential or protected by the attorney-client privilege. It is not intended
for transmission to, or receipt by, any unauthorized persons. If you have
received this message in error, please (i) do not read it, (ii) reply to the
sender that you received the message in error, and (iii) erase or destroy the
message. Legal advice contained in the preceding message is solely for the
benefit of the Foley & Lardner LLP client(s) represented by the Firm in
the particular matter that is the subject of this message, and may not be
relied upon by any other party. <BR><BR><BR>Internal Revenue Service
regulations require that certain types of written advice include a disclaimer.
To the extent the preceding message contains advice relating to a Federal tax
issue, unless expressly stated otherwise the advice is not intended or written
to be used, and it cannot be used by the recipient or any other taxpayer, for
the purpose of avoiding Federal tax penalties, and was not written to support
the promotion or marketing of any transaction or matter discussed herein.<BR><PRE wrap=""><HR width="90%" SIZE=4>
_______________________________________________
cisco-voip mailing list
<A class=moz-txt-link-abbreviated href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</A>
<A class=moz-txt-link-freetext href="https://puck.nether.net/mailman/listinfo/cisco-voip">https://puck.nether.net/mailman/listinfo/cisco-voip</A>
</PRE></BLOCKQUOTE></BODY></HTML>