<br><font size=2 face="sans-serif">Ed/Carlos</font>
<br>
<br><font size=2 face="sans-serif">You are correct the VG248 is not IOS based. It is completely menu driven unfortionatly. However it does talk Skinny back to call manager so the ports all come up and look like phones. Very little configuration on the box itself.</font>
<br>
<br><font size=2 face="sans-serif">Craig Staffin</font>
<br><font size=2 face="sans-serif">____________________________</font>
<br><font size=2 face="sans-serif">Rockwell Automation</font>
<br><font size=2 face="sans-serif">Network Analyst</font>
<br><font size=2 face="sans-serif">cmstaffin@ra.rockwell.com</font>
<br><font size=2 face="sans-serif">414-382-2309</font>
<br>
<br>
<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td>
<td><font size=1 face="sans-serif"><b>"Ortiz, Carlos" <CORTIZ@broward.org></b></font>
<br><font size=1 face="sans-serif">Sent by: cisco-voip-bounces@puck.nether.net</font>
<p><font size=1 face="sans-serif">12/23/2005 09:23 AM</font>
<br>
<td><font size=1 face="Arial"> </font>
<br><font size=1 face="sans-serif"> To: "Ed Leatherman" <ealeatherman@gmail.com></font>
<br><font size=1 face="sans-serif"> cc: cisco-voip@puck.nether.net</font>
<br><font size=1 face="sans-serif"> Subject: RE: [cisco-voip] IOS MGCP question</font></table>
<br>
<br>
<br><font size=2 face="Courier New">I think you are better off with the VG224's. They are IOS based and are<br>
basically like configuring a router. Unless the 248's have changed (I<br>
haven't looked) they are not IOS based and I remember they were a little<br>
more troublesome. Maybe someone else out there can confirm this and you<br>
will feel better about going this route.<br>
<br>
Carlos<br>
<br>
-----Original Message-----<br>
From: Ed Leatherman [mailto:ealeatherman@gmail.com] <br>
Sent: Thursday, December 22, 2005 8:00 PM<br>
To: Ortiz, Carlos<br>
Subject: Re: [cisco-voip] IOS MGCP question<br>
<br>
Hey Carlos good to hear from you. We're getting some VG224's in to use<br>
for a few dormitories at a regional campus, hopefully they will work<br>
out OK. I would have rather gone with some 248's and had fewer boxes<br>
to manage, but the 'customer' wants dual connections to all boxes<br>
where possible.<br>
<br>
On 12/22/05, Ortiz, Carlos <CORTIZ@broward.org> wrote:<br>
> Hey Ed, I remember you from CIPTUG! The newer VG224's work really well<br>
> with MGCP. The only issue I currently have is that my IOS version has<br>
a<br>
> AAA bug in it. I need to upgrade my memory to fix this. Really<br>
hasn't<br>
> impacted me though because the boxes run and I never touch them....<br>
><br>
> Carlos<br>
><br>
> -----Original Message-----<br>
> From: cisco-voip-bounces@puck.nether.net<br>
> [mailto:cisco-voip-bounces@puck.nether.net] On Behalf Of Ed Leatherman<br>
> Sent: Thursday, December 22, 2005 3:42 PM<br>
> To: Kevin Thorngren<br>
> Cc: cisco-voip@puck.nether.net<br>
> Subject: Re: [cisco-voip] IOS MGCP question<br>
><br>
> Kevin,<br>
><br>
> Turns out none of the VG200's I have came with enough flash memory to<br>
> upgrade to any versions supporting MGCP PRI backhaul.. they are all<br>
> 8MB flash and the lowest version of 12.2T that hasnt been removed from<br>
> CCO (that I could find) is just a bit bigger than 8MB. All the 8MB<br>
> versions have been removed, too old I guess. I'll try to get H323<br>
> working for this test instead.<br>
><br>
> I hadn't used the feature navigator before, thanks for showing me.<br>
><br>
> Ed<br>
><br>
> On 12/22/05, Kevin Thorngren <kthorngr@cisco.com> wrote:<br>
> > Hi Ed,<br>
> ><br>
> > According to the Feature Navigator 12.2(16a) on the VG200 does not<br>
> > support MGCP PRI backhaul to CCM. You will need to use a 12.2T<br>
> version<br>
> > or a 12.3 version on the VG200.<br>
> ><br>
> > You can search by feature from here:<br>
> > http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp<br>
> ><br>
> > Look for the feature "MGCP PRI backhaul and T1-CAS support for Call<br>
> > Manager (IP-PBX)". Then select the VG200. This will give you all<br>
> your<br>
> > options and you can determine which IOS will best fit your needs.<br>
> ><br>
> > Also for a back to back config don't forget to but the "isdn<br>
> > protocol-emulate network" command on the serial interface of one of<br>
> the<br>
> > routers to bring up layer 2.<br>
> ><br>
> > HTH,<br>
> > Kevin<br>
> ><br>
><br>
> _______________________________________________<br>
> cisco-voip mailing list<br>
> cisco-voip@puck.nether.net<br>
> https://puck.nether.net/mailman/listinfo/cisco-voip<br>
><br>
<br>
_______________________________________________<br>
cisco-voip mailing list</font>
<br><font size=2 face="Courier New">cisco-voip@puck.nether.net<br>
https://puck.nether.net/mailman/listinfo/cisco-voip<br>
</font>
<br>
<br>