<div>Hi Kevin,</div>
<div> </div>
<div>I tried all those different pattern, but still can't get any response (even the outside dial tone). and I use debug isdn q.921/q.931/event but no see anything in my voice gateway. is it possible that i wrong configure in gateway ? how can I verify is there any signal really comes from CCM to my MGCP gateway? Thanks a lot ~
</div>
<div> </div>
<div> </div>
<div>Regards,</div>
<div> </div>
<div>Alan<br><br> </div>
<div><span class="gmail_quote">2006/4/12, Kevin Thorngren <<a href="mailto:kthorngr@cisco.com">kthorngr@cisco.com</a>>:</span>
<blockquote class="gmail_quote" style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid">Hi Alan,<br><br>I had a typo below. In the US we would dial 011 for international<br>patterns. My below example should have had
9.011!. The "!" allows<br>users to keep dialing digits until the interdigit timeout timer expires<br>(15 seconds). You could use the following two patterns:<br><br>9.!<br>9.!#<br><br>The "#" allows the users to terminate the dialing with a #. Point both
<br>Route Patterns to the same GW or RL.<br><br>Once CCM determines the call is an outside call then it will play<br>outside dialtone. If you don't have any internal patterns that begin<br>with 9 then the users should hear outside dialtone after the 9 is
<br>dialed. The "!" allows them to continue dialing. In the first pattern<br>CCM will wait 15 seconds after the last digit (interdigit timeout)<br>before extending the call. The second pattern allows the user to
<br>terminate the dialing with a # and CCM will extend the call right away.<br><br>Here is an example of the UK numbering plan.<br><a href="http://www.cisco.com/en/US/partner/products/sw/voicesw/ps556/">http://www.cisco.com/en/US/partner/products/sw/voicesw/ps556/
</a><br>products_tech_note09186a008028af3a.shtml<br><br>Kevin<br><br>On Apr 11, 2006, at 11:42 AM, Alan Su wrote:<br><br>> Hi Kelvin,<br>> <br>> Thanks a lot, I'll study those valuable documents you share with me.
<br>> Regarding the dialing pattern, I also have below questions:<br>> 1. What if I'm in out of US ? Do I still can use @ for typical north<br>> American dial plan ?<br>> <br>> 2. Can user only dial one digit (ex:9), and after hearing the dial
<br>> tone then begin to dial the outside number? In this case, I can't set<br>> the full pattern in my route pattern, how should I configure it ?<br>> <br>> Many many thanks for your help.<br>> <br>> <br>
> Regards,<br>> <br>> Alan<br>><br>> <br>> 2006/4/11, Kevin Thorngren <<a href="mailto:kthorngr@cisco.com">kthorngr@cisco.com</a>>: Hi Alan,<br>>><br>>> The 9. pattern needs to match the full pattern you are
using.Some<br>>> examples are:<br>>><br>>> 9.@ - typical north American dial plan macro that matches local, ld<br>>> and<br>>> international patterns.<br>>> 9.[2-9]XXXXXX - More specific pattern for local 7 digit dialing
<br>>> 9.1[2-9]XX[2-9]XXXXXX - More specific pattern for LD dialing<br>>> 9.011T - More specifc pattern for international dialing<br>>><br>>> The CCM will need to match the full pattern dialed from the phone
<br>>> before extending the call to the GW.With 9. the GW is receiving a<br>>> blank dialed number (assuming you are doing pre-dot discard).Also<br>>> you<br>>> will want to select the option for outside
dialtone.The below links<br>>> should help describe this.<br>>><br>>> <a href="http://www.cisco.com/en/US/products/sw/voicesw/ps556/">http://www.cisco.com/en/US/products/sw/voicesw/ps556/</a><br>>> products_tech_note09186a0080094b2a.shtml
<br>>><br>>> <a href="http://www.cisco.com/en/US/products/sw/voicesw/ps556/">http://www.cisco.com/en/US/products/sw/voicesw/ps556/</a><br>>> products_tech_note09186a00800945b9.shtml<br>>><br>>>
<a href="http://www.cisco.com/en/US/products/sw/voicesw/ps556/">http://www.cisco.com/en/US/products/sw/voicesw/ps556/</a><br>>> products_administration_guide_chapter09186a00803edabe.html<br>>><br>>> <a href="http://www.cisco.com/en/US/products/sw/voicesw/ps556/">
http://www.cisco.com/en/US/products/sw/voicesw/ps556/</a><br>>> products_administration_guide_chapter09186a00803ed685.html<br>>><br>>> HTH,<br>>> Kevin<br>>> On Apr 11, 2006, at 7:47 AM, Alan Su wrote:
<br>>><br>>> > Dear All,<br>>> ><br>>> > My IPT architecture is: CCM(4.02) + Voice Gateway(3745 runing MGCP<br>>> w/<br>>> > E1 PRI trunk to PSTN).<br>>> > I already configured the MGCP and ccm-manager option in the voice
<br>>> > gateway, and it's registered to CM without any problem.<br>>> > I also made the gateway configuratio in CCM to this router.<br>>> ><br>>> > Right now my problem is, I don't know how to setup the route pattern
<br>>> > to allow IP Phone to make outside call.<br>>> > My idea is, when user dial "9", the phone will provide an outside<br>>> dial<br>>> > tone and user can directly dial the PSTN phone number to complete a
<br>>> > call (just like the old fashion way). But when I configure the route<br>>> > pattern "9." and set the S1/DS1-0@VGW to be the gateway, there is<br>>> > nothing but a "Bad Address".
<br>>> ><br>>> > Does anyone know how to find the reference document for the<br>>> > configuration or how to fix this problem? I did lots of search but<br>>> > nothing found. Any comment would be very grateful. Thanks a lot ~
<br>>> ><br>>> ><br>>> > Regards,<br>>> ><br>>> > Alan<br>>> > <VGW-Config.txt>_______________________________________________<br>>> > cisco-voip mailing list
<br>>> > <a href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a><br>>> > <a href="https://puck.nether.net/mailman/listinfo/cisco-voip">https://puck.nether.net/mailman/listinfo/cisco-voip
</a><br>>><br><br></blockquote></div><br>