<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
  <meta content="text/html;charset=ISO-8859-7" http-equiv="Content-Type">
</head>
<body bgcolor="#ffffff" text="#000000">
<tt>Ryan<br>
here is a csim start command from that router<br>
<br>
<font color="#3333ff"><i>Lon2851#csim start 90030xxxxxxxxxx<br>
csim: called number = 90030</i></font></tt><tt><font color="#3333ff"><i>xxxxxxxxxx</i></font></tt><tt><font
 color="#3333ff"><i>, loop count = 1 ping count = 0<br>
<br>
*Jun 29 11:11:08.959: ISDN Se0/2/0:15 Q931: Applying typeplan for
sw-type 0x12 is 0x0 0x0, Called num 0030</i></font></tt><tt><font
 color="#3333ff"><i>xxxxxxxxxx</i></font></tt><br>
<tt><font color="#3333ff"><i>*Jun 29 11:11:08.959: ISDN Se0/2/0:15
Q931: TX -&gt; SETUP pd = 8  callref = 0x0164 <br>
        Bearer Capability i = 0x8090A3 <br>
                Standard = CCITT <br>
                Transfer Capability = Speech  <br>
                Transfer Mode = Circuit <br>
                Transfer Rate = 64 kbit/s <br>
        Channel ID i = 0xA9839E <br>
                Exclusive, Channel 30 <br>
        Called Party Number i = 0x80, '0030</i></font></tt><tt><font
 color="#3333ff"><i>xxxxxxxxxx</i></font></tt><tt><font color="#3333ff"><i>'
<br>
                Plan:Unknown, Type:Unknown<br>
*Jun 29 11:11:09.103: ISDN Se0/2/0:15 Q931: RX &lt;- SETUP_ACK pd = 8 
callref = 0x8164 <br>
        Channel ID i = 0xA9839E <br>
                Exclusive, Channel 30 <br>
        Progress Ind i = 0x8288 - In-band info or appropriate now
available <br>
*Jun 29 11:11:15.555: ISDN Se0/2/0:15 Q931: RX &lt;- ALERTING pd = 8 
callref = 0x8164<br>
*Jun 29 11:11:17.839: ISDN Se0/2/0:15 Q931: RX &lt;- CONNECT pd = 8 
callref = 0x8164<br>
*Jun 29 11:11:17.839: %ISDN-6-CONNECT: Interface Serial0/2/0:29 is now
connected to </i></font></tt><tt><font color="#3333ff"><i>xxxxxxxxxx</i></font></tt><tt><font
 color="#3333ff"><i> N/A<br>
*Jun 29 11:11:17.839: ISDN Se0/2/0:15 Q931: TX -&gt; CONNECT_ACK pd =
8  callref = 0x0164<br>
*Jun 29 11:11:18.391: ISDN Se0/2/0:15 Q931: RX &lt;- DISCONNECT pd = 8 
callref = 0x8164 <br>
        Cause i = 0x8090 - Normal call clearing <br>
        Progress Ind i = 0x8288 - In-band info or appropriate now
available <br>
*Jun 29 11:11:18.395: ISDN Se0/2/0:15 Q931: call_disc: PI received in
disconnect; Postpone sending RELEASE for callid 0x8164.<br>
csim: loop = 1, failed = 0  <br>
csim: call attempted = 1, setup failed = 0, tone failed = 1<br>
<br>
Lon2851#</i></font><br>
</tt><br>
I guess there is no Calling party in the setup message.<br>
When there is a call from an ip phone, there is calling party (the
extension of the ccm). Of course the POTS provider just shows the
number of the PRI to the called party and not the internal extension of
the CCM.<br>
But when i make calls from the router ( with csim start) or the fxs (a
modem attached there), there is no calling party on the q931setup
message and so the provider does not shows anything to the called.<br>
I have tried configuring isdn calling-number etc on the serial 0/2/0:15
but nothing changes. Must i put something there or at the dial-peer
pots?<br>
The customer wants this feature desperately!!!<br>
<br>
Cheers,<br>
Anthony<br>
Ryan Ratliff wrote:
<blockquote cite="mid7747FB40-03EA-472C-B947-95F8336708A9@cisco.com"
 type="cite">Do you have a q931 debug showing the outbound call?
  <br>
  <br>
-Ryan
  <br>
  <br>
On Jun 28, 2006, at 12:03 PM, Anthony Kouloglou wrote:
  <br>
  <br>
Hi all,
  <br>
on a 2851 with one E1 and 4 FXS ports i have configured the voice port
  <br>
as follows:
  <br>
  <br>
voice-port 0/3/2
  <br>
 cptone GB
  <br>
 description xxx
  <br>
 station-id name yyy
  <br>
 station-id number 1234
  <br>
 caller-id enable type 1
  <br>
  <br>
  <br>
there is also these:
  <br>
  <br>
voice-port 0/2/0:15
  <br>
 translation-profile incoming TP01
  <br>
 bearer-cap Speech
  <br>
interface Serial0/2/0:15
  <br>
 no ip address
  <br>
 isdn switch-type primary-net5
  <br>
 isdn incoming-voice voice
  <br>
 no cdp enable
  <br>
  <br>
  <br>
dial-peer voice 10 pots
  <br>
 destination-pattern 9T
  <br>
 port 0/2/0:15
  <br>
  <br>
  <br>
when i call from the analog phone to an ipphone extension internally i
  <br>
have clid (both name and number) to the ipphone
  <br>
  <br>
but when i make calls through the pri, i get "uknown number" to the
  <br>
external phone that i have called.
  <br>
Is this ficed somehow?
  <br>
  <br>
Cheers
  <br>
Anthony
  <br>
_______________________________________________
  <br>
cisco-voip mailing list
  <br>
<a class="moz-txt-link-abbreviated" href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a>
  <br>
<a class="moz-txt-link-freetext" href="https://puck.nether.net/mailman/listinfo/cisco-voip">https://puck.nether.net/mailman/listinfo/cisco-voip</a>
  <br>
  <br>
</blockquote>
</body>
</html>