<META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=iso-8859-1">
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
</head>
<body bgcolor="#ffffff" text="#000000">
<DIV id=idOWAReplyText32271 dir=ltr>
<DIV dir=ltr><FONT face=Arial color=#000000 size=2>First talk to your provider
and let them know that you wish to control the ANI and not them with the Billing
Number that is associated with the PRI.</FONT></DIV>
<DIV dir=ltr><FONT face=Arial size=2></FONT> </DIV>
<DIV dir=ltr><FONT face=Arial size=2>Brian</FONT></DIV></DIV>
<DIV dir=ltr><BR>
<HR tabIndex=-1>
<FONT face=Tahoma size=2><B>From:</B> cisco-voip-bounces@puck.nether.net on
behalf of Anthony Kouloglou<BR><B>Sent:</B> Thu 6/29/2006 6:19 AM<BR><B>To:</B>
Ryan Ratliff<BR><B>Cc:</B> cisco-voip@puck-nether.net<BR><B>Subject:</B> Re:
[cisco-voip] clid on fxs ports<BR></FONT><BR></DIV>
<DIV><TT>Ryan<BR>here is a csim start command from that router<BR><BR><FONT
color=#3333ff><I>Lon2851#csim start 90030xxxxxxxxxx<BR>csim: called number =
90030</I></FONT></TT><TT><FONT
color=#3333ff><I>xxxxxxxxxx</I></FONT></TT><TT><FONT color=#3333ff><I>, loop
count = 1 ping count = 0<BR><BR>*Jun 29 11:11:08.959: ISDN Se0/2/0:15 Q931:
Applying typeplan for sw-type 0x12 is 0x0 0x0, Called num
0030</I></FONT></TT><TT><FONT
color=#3333ff><I>xxxxxxxxxx</I></FONT></TT><BR><TT><FONT color=#3333ff><I>*Jun
29 11:11:08.959: ISDN Se0/2/0:15 Q931: TX -> SETUP pd = 8 callref =
0x0164 <BR> Bearer Capability i =
0x8090A3
<BR>
Standard = CCITT
<BR>
Transfer Capability = Speech
<BR>
Transfer Mode = Circuit
<BR>
Transfer Rate = 64 kbit/s <BR> Channel
ID i = 0xA9839E
<BR>
Exclusive, Channel 30 <BR> Called
Party Number i = 0x80, '0030</I></FONT></TT><TT><FONT
color=#3333ff><I>xxxxxxxxxx</I></FONT></TT><TT><FONT color=#3333ff><I>'
<BR>
Plan:Unknown, Type:Unknown<BR>*Jun 29 11:11:09.103: ISDN Se0/2/0:15 Q931: RX
<- SETUP_ACK pd = 8 callref = 0x8164
<BR> Channel ID i = 0xA9839E
<BR>
Exclusive, Channel 30 <BR> Progress
Ind i = 0x8288 - In-band info or appropriate now available <BR>*Jun 29
11:11:15.555: ISDN Se0/2/0:15 Q931: RX <- ALERTING pd = 8 callref =
0x8164<BR>*Jun 29 11:11:17.839: ISDN Se0/2/0:15 Q931: RX <- CONNECT pd =
8 callref = 0x8164<BR>*Jun 29 11:11:17.839: %ISDN-6-CONNECT: Interface
Serial0/2/0:29 is now connected to </I></FONT></TT><TT><FONT
color=#3333ff><I>xxxxxxxxxx</I></FONT></TT><TT><FONT color=#3333ff><I>
N/A<BR>*Jun 29 11:11:17.839: ISDN Se0/2/0:15 Q931: TX -> CONNECT_ACK pd =
8 callref = 0x0164<BR>*Jun 29 11:11:18.391: ISDN Se0/2/0:15 Q931: RX <-
DISCONNECT pd = 8 callref = 0x8164
<BR> Cause i = 0x8090 - Normal call
clearing <BR> Progress Ind i = 0x8288
- In-band info or appropriate now available <BR>*Jun 29 11:11:18.395: ISDN
Se0/2/0:15 Q931: call_disc: PI received in disconnect; Postpone sending RELEASE
for callid 0x8164.<BR>csim: loop = 1, failed = 0 <BR>csim: call attempted
= 1, setup failed = 0, tone failed = 1<BR><BR>Lon2851#</I></FONT><BR></TT><BR>I
guess there is no Calling party in the setup message.<BR>When there is a call
from an ip phone, there is calling party (the extension of the ccm). Of course
the POTS provider just shows the number of the PRI to the called party and not
the internal extension of the CCM.<BR>But when i make calls from the router (
with csim start) or the fxs (a modem attached there), there is no calling party
on the q931setup message and so the provider does not shows anything to the
called.<BR>I have tried configuring isdn calling-number etc on the serial
0/2/0:15 but nothing changes. Must i put something there or at the dial-peer
pots?<BR>The customer wants this feature
desperately!!!<BR><BR>Cheers,<BR>Anthony<BR>Ryan Ratliff wrote:
<BLOCKQUOTE cite="" type="cite">Do you have a q931 debug showing the outbound
call? <BR><BR>-Ryan <BR><BR>On Jun 28, 2006, at 12:03 PM, Anthony Kouloglou
wrote: <BR><BR>Hi all, <BR>on a 2851 with one E1 and 4 FXS ports i have
configured the voice port <BR>as follows: <BR><BR>voice-port 0/3/2
<BR> cptone GB <BR> description xxx <BR> station-id name yyy
<BR> station-id number 1234 <BR> caller-id enable type 1
<BR><BR><BR>there is also these: <BR><BR>voice-port 0/2/0:15
<BR> translation-profile incoming TP01 <BR> bearer-cap Speech
<BR>interface Serial0/2/0:15 <BR> no ip address <BR> isdn
switch-type primary-net5 <BR> isdn incoming-voice voice <BR> no cdp
enable <BR><BR><BR>dial-peer voice 10 pots <BR> destination-pattern 9T
<BR> port 0/2/0:15 <BR><BR><BR>when i call from the analog phone to an
ipphone extension internally i <BR>have clid (both name and number) to the
ipphone <BR><BR>but when i make calls through the pri, i get "uknown number"
to the <BR>external phone that i have called. <BR>Is this ficed somehow?
<BR><BR>Cheers <BR>Anthony <BR>_______________________________________________
<BR>cisco-voip mailing list <BR><A class=moz-txt-link-abbreviated
href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</A> <BR><A
class=moz-txt-link-freetext
href="https://puck.nether.net/mailman/listinfo/cisco-voip">https://puck.nether.net/mailman/listinfo/cisco-voip</A>
<BR><BR></BLOCKQUOTE></DIV>
</body>
</html>