<HTML>
<HEAD>
<TITLE>Re: [cisco-voip] Using VWIC-2MFT card with voice and data</TITLE>
</HEAD>
<BODY>
<FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'>This is the doc I was looking for!<BR>
<BR>
And out of frustration, I tried configuring it last night and it worked – before, when I would configure a pri-group on the second controller, I got an error but now it’s letting me configure it.<BR>
<BR>
So now we can start selling 2 port cards – one for voice the other for data rather than two single port cards.<BR>
<BR>
Thanks for all of the help, from the only listserv I subscribe to anymore due to the excellent signal/noise ratio.<BR>
<BR>
Chris<BR>
<BR>
<BR>
On 7/17/06 7:48 PM, "ash AD" <commo_ssg_31f@yahoo.com> wrote:<BR>
<BR>
</SPAN></FONT><BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'>I have always been told no, this could not be done but some documentation says otherwise. Maybe the below URLs is what you are refering to:<BR>
<BR>
<BR>
<BR>
<a href="http://www.cisco.com/en/US/products/ps5855/products_qanda_item0900aecd8028d2e5.shtml">http://www.cisco.com/en/US/products/ps5855/products_qanda_item0900aecd8028d2e5.shtml</a><BR>
<BR>
<BR>
<BR>
<a href="http://www.cisco.com/en/US/products/hw/modules/ps2617/products_configuration_example09186a008052c920.shtml">http://www.cisco.com/en/US/products/hw/modules/ps2617/products_configuration_example09186a008052c920.shtml</a><BR>
<BR>
<BR>
Let us know if you make it work.<BR>
<BR>
<BR>
<BR>
Peter Casanave<BR>
<BR>
<B><I>"Jason Aarons (US)" <jason.aarons@us.didata.com></I></B> wrote:<BR>
<BR>
</SPAN></FONT><BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'>Only issues might be clocking from different sources on the two T1s.<BR>
There are clocking limitations on the VWIC2-2MFT-T1/E1. However in<BR>
general it does work, I have lots of sites with this configuration. <BR>
<BR>
I would try and stick with a WIC1-DSU if you not sure on the telco<BR>
clocking -jason<BR>
<BR>
-----Original Message-----<BR>
From: cisco-voip-bounces@puck.nether.net<BR>
[<a href="mailto:cisco-voip-bounces@puck.nether.net]">mailto:cisco-voip-bounces@puck.nether.net]</a> On Behalf Of Chris Ellington<BR>
Sent: Monday, July 17, 2006 10:30 AM<BR>
To: cisco-voip@puck.nether.net<BR>
Subject: [cisco-voip] Using VWIC-2MFT card with voice and data<BR>
<BR>
I know it hasn't been supported to use a 2MFT card with one port T1 data<BR>
and the other port PRI but I seem to remember seeing a doc stating that<BR>
it was supported.<BR>
<BR>
At present, my TAC engineer thinks I nuts and can't find the doc. <BR>
<BR>
Anyone on the list recall seeing this?<BR>
<BR>
Thanks!<BR>
<BR>
Chris<BR>
</SPAN></FONT></BLOCKQUOTE></BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'><BR>
<BR>
-- <BR>
</SPAN></FONT><SPAN STYLE='font-size:12.0px'><FONT FACE="Onyx">Christopher S. Ellington<BR>
CCIE #6814<BR>
Network Solutions, Inc.<BR>
(317) 566 8897<BR>
Chris.Ellington@nsi1.com</FONT><FONT FACE="Verdana, Helvetica, Arial"><BR>
</FONT></SPAN>
</BODY>
</HTML>