Yeah I did that. But still no go.<br>Here is the sho voice port 0/0/0 command output:<br><br>ho voice port 0/0/0<br><br>Foreign Exchange Office 0/0/0 Slot is 0, Sub-unit is 0, Port is 0<br> Type of VoicePort is FXO<br> Operation State is DORMANT
<br> Administrative State is UP<br> The Last Interface Down Failure Cause is Administrative Shutdown<br> Description is 555-123-4567<br> Noise Regeneration is enabled<br> Non Linear Processing is enabled<br> Non Linear Mute is disabled
<br> Non Linear Threshold is -21 dB<br> Music On Hold Threshold is Set to -38 dBm<br> In Gain is Set to 0 dB<br> Out Attenuation is Set to 3 dB<br> Echo Cancellation is enabled<br> Echo Cancellation NLP mute is disabled<br>
Echo Cancellation NLP threshold is -21 dB<br> Echo Cancel Coverage is set to 48 ms<br> Echo Cancel worst case ERL is set to 6 dB<br> Playout-delay Mode is set to adaptive<br> Playout-delay Nominal is set to 60 ms<br> Playout-delay Maximum is set to 250 ms
<br> Playout-delay Minimum mode is set to default, value 40 ms <br> Playout-delay Fax is set to 300 ms<br> Connection Mode is plar<br> Connection Number is 2002<br> Initial Time Out is set to 10 s<br> Interdigit Time Out is set to 10 s
<br> Call Disconnect Time Out is set to 60 s<br> Ringing Time Out is set to 180 s<br> Wait Release Time Out is set to 30 s<br> Companding Type is u-law<br> Region Tone is set for US<br><br> Analog Info Follows:<br> Currently processing none
<br> Maintenance Mode Set to None (not in mtc mode)<br> Number of signaling protocol errors are 0<br> Impedance is set to 600r Ohm<br> Station name None, Station number None<br> Translation profile (Incoming): <br> Translation profile (Outgoing):
<br><br> Voice card specific Info Follows:<br> Signal Type is loopStart<br> Battery-Reversal is enabled<br> Number Of Rings is set to 1<br> Supervisory Disconnect is signal<br> Answer Supervision is inactive<br> Hook Status is On Hook
<br> Ring Detect Status is inactive<br> Ring Ground Status is inactive<br> Tip Ground Status is inactive<br> Dial Out Type is dtmf<br> Digit Duration Timing is set to 100 ms<br> InterDigit Duration Timing is set to 100 ms
<br> Pulse Rate Timing is set to 10 pulses/second<br> InterDigit Pulse Duration Timing is set to 750 ms<br> Percent Break of Pulse is 60 percent<br> GuardOut timer is 2000 ms<br> Minimum ring duration timer is 125 ms<br> Hookflash-in Timing is set to 600 ms
<br> Hookflash-out Timing is set to 500 ms<br> Supervisory Disconnnct Timing is set to 350 ms<br><br>I think I am missing something basic. This has happened before and the only way to fix it was to reboot the 2801.<br><br>
Todd<br><br><div><span class="gmail_quote">On 4/30/07, <b class="gmail_sendername">Adam</b> <<a href="mailto:cisco@adman.net">cisco@adman.net</a>> wrote:</span><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
How about a 'shutdown' followed by 'no shutdown' in the voice-port<br>configuration?<br><br>-Adam<br><br>On 4/30/07, Todd Franklin <<a href="mailto:toddnh65@gmail.com">toddnh65@gmail.com</a>> wrote:<br>
> Apparently my FXO port is hung internally. I can't easily reboot this box<br>> since it has my PRI on it as well.<br>> Is there a command to just reset the FXO port? Right now I have my telco<br>> busying it out so it will fall over to the next line (which comes in on the
<br>> PRI).<br>><br>> Thanks anyone!<br>><br>> _______________________________________________<br>> cisco-voip mailing list<br>> <a href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a>
<br>> <a href="https://puck.nether.net/mailman/listinfo/cisco-voip">https://puck.nether.net/mailman/listinfo/cisco-voip</a><br>><br>><br></blockquote></div><br>