Friends,<br><br>I configured 3825 router as RAS but not working. You can find the sh running, show version and debug isdn q931 outputs.<br><br>Hardware: 3825, NM-HDV2-2T1/E1, pvdm2-64, NM-30DM<br><br>Topology:<br>RAS------(PRI)------PBX----------Dialup User<br>
<br>Configuration:<br><br><br> ++++++++++++++ Show Running ++++++++++++++++++<br><br> RAS#sh run<br> Building configuration...<br><br> Current configuration : 2613 bytes<br> !<br> version 12.4<br> service timestamps debug datetime msec<br>
service timestamps log datetime msec<br> no service password-encryption<br> !<br> hostname RAS<br> !<br> boot-start-marker<br> boot-end-marker<br> !<br> card type e1 0 0<br> card type e1 2 1<br>
enable password cisco<br> !<br> aaa new-model<br> !<br> !<br> aaa authentication login abc local<br> !<br> !<br> aaa session-id common<br> no network-clock-participate slot 2 <br> no network-clock-participate wic 0 <br>
ip cef<br> !<br> multilink virtual-template 1<br> multilink bundle-name authenticated<br> !<br> isdn switch-type primary-qsig<br> isdn voice-call-failure 0<br> voice-card 0<br> no dspfarm<br> !<br>
voice-card 2<br> no dspfarm<br> !<br> !<br> username admin password 0 cisco<br> !<br> !<br> controller E1 0/0/0<br> channel-group 0 timeslots 1-31<br> !<br> controller E1 0/0/1<br> !<br>
controller E1 2/0<br> pri-group timeslots 1-31<br> !<br> controller E1 2/1<br> vlan internal allocation policy ascending<br> ! <br> !<br> interface Loopback0<br> ip address <a href="http://10.10.10.1">10.10.10.1</a> <a href="http://255.255.255.255">255.255.255.255</a><br>
!<br> interface GigabitEthernet0/0<br> no ip address<br> shutdown<br> duplex auto<br> speed auto<br> media-type rj45<br> no keepalive<br> ! <br> interface GigabitEthernet0/1<br>
no ip address<br> shutdown<br> duplex auto<br> speed auto<br> media-type rj45<br> no keepalive<br> !<br> interface Serial0/0/0:0<br> no ip address<br> !<br> interface Serial2/0:15<br>
ip unnumbered Loopback0<br> encapsulation ppp<br> dialer idle-timeout 2147483<br> dialer-group 1<br> isdn switch-type primary-qsig<br> isdn timer T310 120000<br> isdn protocol-emulate network<br>
isdn incoming-voice modem<br> no fair-queue<br> ppp authentication pap<br> ppp multilink<br> !<br> interface Virtual-Template1 <br> description Multilink for Async Users<br> ip unnumbered Loopback0<br>
timeout absolute 5400 0<br> peer default ip address pool dialpool<br> ppp authentication pap<br> ppp multilink<br> ppp multilink fragment disable<br> !<br> interface Dialer1<br> ip unnumbered Loopback0<br>
encapsulation ppp<br> no ip mroute-cache<br> dialer in-band<br> dialer idle-timeout 0<br> dialer-group 1<br> peer default ip address pool dialpool<br> no fair-queue<br> no cdp enable<br> ppp authentication pap callin<br>
ppp multilink<br> ! <br> interface Group-Async0<br> no ip address<br> encapsulation ppp<br> no snmp trap link-status<br> async dynamic address<br> async mode dedicated<br> peer default ip address pool dialpool<br>
no fair-queue<br> ppp max-bad-auth 3<br> ppp authentication pap<br> ppp multilink<br> group-range 1/0 1/29<br> !<br> ip local pool dialpool <a href="http://10.10.10.10">10.10.10.10</a> <a href="http://10.10.10.40">10.10.10.40</a><br>
!<br> !<br> ip http server<br> no ip http secure-server<br> ! <br> !<br> !<br> control-plane<br> !<br> !<br> !<br> voice-port 2/0:15<br> !<br> line con 0<br> stopbits 1<br>
line aux 0<br> line 1/0 1/29<br> exec-timeout 0 0<br> no flush-at-activation<br> modem Dialin<br> modem autoconfigure type si3<br> transport input all<br> autoselect during-login<br> autoselect ppp<br>
line vty 0 4<br> !<br> scheduler allocate 20000 1000<br> !<br> end<br><br> +++++++++++++ Sh Verion ++++++++++++++<br><br> RAS#sh ver<br> Cisco IOS Software, 3800 Software (C3825-ADVENTERPRISEK9-M), Version 12.4(11)XJ4, RELEASE SOFTWARE (fc2)<br>
<br> ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)<br><br> RAS uptime is 26 minutes<br> System returned to ROM by reload at 12:40:18 UTC Thu Feb 28 2008<br> System image file is "flash:c3825-adventerprisek9-mz.124-11.XJ4.bin"<br>
<br><br><br> Cisco 3825 (revision 1.1) with 221184K/40960K bytes of memory.<br> Processor board ID FCZ11057005<br> 2 Gigabit Ethernet interfaces<br> 33 Serial interfaces<br> 30 terminal lines<br> 4 Channelized E1/PRI ports<br>
2 Virtual Private Network (VPN) Modules<br> DRAM configuration is 64 bits wide with parity enabled.<br> 479K bytes of NVRAM.<br> 62720K bytes of ATA System CompactFlash (Read/Write)<br><br> Configuration register is 0x2102<br>
<br> RAS#<br><br> ++++++++++++++ Debug ISDN Q931 +++++++++++++++<br><br> RAS#<br> *Feb 28 13:08:45.891: ISDN Se2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x2CD6 <br> Bearer Capability i = 0x8090A3 <br>
Standard = CCITT <br> Transfer Capability = Speech <br> Transfer Mode = Circuit <br> Transfer Rate = 64 kbit/s <br> Channel ID i = 0xA18396 <br>
Preferred, Channel 22 <br> Facility i = 0x9FAA068001008201008B0100A1100201010201008008545247524F4F4D20 <br> Progress Ind i = 0x8183 - Origination address is non-ISDN <br> Calling Party Number i = 0x0181, '35240' <br>
Plan:ISDN, Type:Unknown <br> Called Party Number i = 0x81, '8701' <br> Plan:ISDN, Type:Unknown <br> Shift to Codeset 5 <br> Codeset 5 IE 0x31 i = 0x80 <br>
Shift to Codeset 5 <br> Codeset 5 IE 0x32 i = 0x81<br> *Feb 28 13:08:45.891: %CSM-1-NO_CHANNEL: Signaling channel not available<br> *Feb
28 13:08:45.891: ISDN Se2/0:15 **ERROR**: accept_incoming_csm_call:
modem problem Requested circuit/channel not available(0x2C): b channel
21, call id 0x6<br> *Feb 28 13:08:45.895: ISDN Se2/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xACD6 <br> Channel ID i = 0xA98396 <br> Exclusive, Channel 22<br> *Feb 28 13:08:45.895: ISDN Se2/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0xACD6 <br>
Cause i = 0x82AC - Requested circuit/channel not available<br> *Feb 28 13:08:45.983: ISDN Se2/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x2CD6 <br> Cause i = 0x81AC - Requested circuit/channel not available<br>
*Feb 28 13:08:45.983: ISDN Se2/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xACD6<br> *Feb 28 13:08:46.059: ISDN Se2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x2CD7 <br> Bearer Capability i = 0x8090A3 <br>
Standard = CCITT <br> Transfer Capability = Speech <br> Transfer Mode = Circuit <br> Transfer Rate = 64 kbit/s <br> Channel ID i = 0xA18397 <br>
Preferred, Channel 23 <br> Facility i = 0x9FAA068001008201008B0100A1100201010201008008545247524F4F4D20 <br> Progress Ind i = 0x8183 - Origination address is non-ISDN <br> Calling Party Number i = 0x0181, '35240' <br>
Plan:ISDN, Type:Unknown <br> Called Party Number i = 0x81, '8701' <br> Plan:ISDN, Type:Unknown <br> Shift to Codeset 5 <br> Codeset 5 IE 0x31 i = 0x80 <br>
Shift to Codeset 5 <br> Codeset 5 IE 0x32 i = 0x81<br> *Feb 28 13:08:46.059: <b>%CSM-1-NO_CHANNEL: Signaling channel not available</b><br> *Feb
28 13:08:46.059: <b>ISDN Se2/0:15 **ERROR**: accept_incoming_csm_call:
modem problem Requested circuit/channel not available(0x2C): b channel
22, call id 0x7</b><br> *Feb 28 13:08:46.059: ISDN Se2/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xACD7 <br> Channel ID i = 0xA98397 <br> Exclusive, Channel 23<br> *Feb 28 13:08:46.059: ISDN Se2/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0xACD7 <br>
Cause i = 0x82AC - Requested circuit/channel not available<br> *Feb 28 13:08:46.163: ISDN Se2/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x2CD7 <br> Cause i = 0x81AC - Requested circuit/channel not available<br>
*Feb 28 13:08:46.163: ISDN Se2/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xACD7<br> RAS#<br><br>Please help me get this issue resolved.<br><br>Regards