<div>Berbee's got a new product to interface with the current PA systems. I would go that way. and you can download a trail for it for 30 days also.... but you would need the hardware piece to interface with your PA system.</div>
<div> </div>
<div>Scott<br><br></div>
<div class="gmail_quote">On Tue, Feb 26, 2008 at 3:40 PM, Lelio Fulgenzi <<a href="mailto:lelio@uoguelph.ca">lelio@uoguelph.ca</a>> wrote:<br>
<blockquote class="gmail_quote" style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid">Thanks Mike and Monica for your replies. It makes sense with the FXO ports<br>and being able to ship out digits to control the zone. I was hoping I could<br>
do this with FXS ports - that's where I was seeing difficulty with the delay<br>in sending digits out.<br><br>I can understand it being cheaper with the paging controller, but with<br>IPCelerate, I'm hoping we can make things easier and group zone by graphical<br>
interface rather than a list of buildings and zones.<br>
<div class="Ih2E3d"><br>--------------------------------------------------------------------------------<br>Lelio Fulgenzi, B.A.<br>Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1<br>(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)<br>
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^<br></div>"Bad grammar makes me [sic]" - Tshirt<br>
<div class="Ih2E3d"><br>----- Original Message -----<br>From: "Norton, Mike" <<a href="mailto:mikenorton@pwsd76.ab.ca">mikenorton@pwsd76.ab.ca</a>><br>To: "Cisco Voip List" <<a href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a>><br>
Sent: Tuesday, February 26, 2008 5:00 PM<br>Subject: Re: [cisco-voip] overhead paging vs ip phones<br><br><br></div>
<div>
<div></div>
<div class="Wj3C7c">> Correct. The workaround is to configure the zone controller to connect<br>> to an FXO port. That way you can do your digit manipulation with route<br>> patterns in CM. For example, make a pattern 1234.XX that strips pre-dot<br>
> and routes out the FXO port. Then tell IPcelerate to call 123456 and it<br>> will pass 56 to the zone controller.<br>><br>> Overall, I have not found IPcelerate's integration with overhead zone<br>> controllers to be very elegant. It works better just to let users call<br>
> the zone controller directly. Not to mention it's way easier and cheaper<br>> to set up this way.<br>><br>> --<br>> Mike Norton<br>> I.T. Support<br>> Peace Wapiti School Division No. 76<br>> Helpdesk: (780) 831-3080<br>
> Direct: (780) 831-3076<br>><br>><br>> -----Original Message-----<br>> From: Lelio Fulgenzi<br>><br>> Can anyone comment on how IPCelerate interfaces with Bogen zone paging<br>> controllers for example? If I setup zones on the Bogen, can the<br>
> IPCelerate call in and punch in the zone as well? I thought all that<br>> DTMF and pauses was not supported?<br>><br>><br>> _______________________________________________<br>> cisco-voip mailing list<br>
> <a href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a><br>> <a href="https://puck.nether.net/mailman/listinfo/cisco-voip" target="_blank">https://puck.nether.net/mailman/listinfo/cisco-voip</a><br>
><br><br>_______________________________________________<br>cisco-voip mailing list<br><a href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a><br><a href="https://puck.nether.net/mailman/listinfo/cisco-voip" target="_blank">https://puck.nether.net/mailman/listinfo/cisco-voip</a><br>
</div></div></blockquote></div><br>