<div>Hi, <br><br>I am trying to configure DSPFarm for ad-hoc multiparty conferencing as per documentation but when i try to configure maximum session in "dspfarm profile 2 conference", the available value is just 0. and when i execute sh dspfarm all command, the output you can see below: <br>
<br>CME#sh dspfarm all <br>Dspfarm Profile Configuration <br><br>Profile ID = 2, Service = CONFERENCING, Resource ID = 1 <br>Profile Description : <br>Profile Admin State : DOWN <br>Profile Operation State : DOWN <br>Application : SCCP Status : NOT ASSOCIATED <br>
Resource Provider : FLEX_DSPRM Status : NONE <br>Number of Resource Configured : 0 <br>Number of Resource Available : 0 <br>Codec Configuration <br>Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required <br>
Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required <br>Codec : g729ar8, Maximum Packetization Period : 60 , Transcoder: Not Required <br>Codec : g729abr8, Maximum Packetization Period : 60 , Transcoder: Not Required <br>
Codec : g729r8, Maximum Packetization Period : 60 , Transcoder: Not Required <br>Codec : g729br8, Maximum Packetization Period : 60 , Transcoder: Not Required <br><br>Total number of DSPFARM DSP channel(s) 0 <br><br>CME#sh inventory <br>
NAME: "2811 chassis", DESCR: "2811 chassis" <br>PID: CISCO2811 , VID: V05 , SN: FCZ120872XE <br><br>NAME: "WAN Interface Card - Serial (1T) on Slot 0 SubSlot 0", DESCR: "WAN Interface Card - Serial (1T)" <br>
PID: WIC-1T= , VID: 1.0, SN: 36242834 <br><br>NAME: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 1", DESCR: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1" <br>PID: VWIC2-1MFT-T1/E1 , VID: V01 , SN: FOC12122L32 <br>
<br>NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "2nd generation four port FXO voice interface daughtercard" <br>PID: VIC2-4FXO , VID: V03 , SN: FOC12081UJ3 <br>
<br>NAME: "PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with one DSP" <br>PID: PVDM2-16 , VID: V01 , SN: FOC11525U28 <br><br>NAME: "PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 5", DESCR: "PVDMII DSP SIMM with one DSP" <br>
PID: PVDM2-16 , VID: V01 , SN: FOC12085AAK <br><br>NAME: "AIM Service Engine 0", DESCR: "AIM Service Engine" <br>PID: AIM-CUE , VID: V03 , SN: FOC12043MQE <br><br>If you think there is any problem with configuration, please write down sample steps for Ad-Hoc Conferencing for more then 3 participants. <br>
Waiting for immediate response <br><br>Note: i am using CME on cisco 2811 with ios c2800nm-spservicesk9-mz.124-15.T5.</div>
<div> </div>
<div>Waiting for your immediate response</div>
<div> </div>
<div>Best Regards</div>