<p><font size=2 color=navy face=Arial>
Yes that is correct<br>The dids are not being used. And the only number I am interested in is 1700 the pilot number that is not live. This issue is only happening on dids that are in the pri list that the client will not be using<br><br>Yes I have checked that multiframe established is there and I have seen the 2nd call hit the router for the debug q931
<br>Cheers
<br>
<br>Leslie Meade
<br>------------------------
<br>Sent using a SIGNAL powered BlackBerry
<br></font></p>
<p><hr size=2 width="100%" align=center tabindex=-1>
<font face=Tahoma size=2>
<b>From</b>: Moataz Mamdouh <moataz_mmdh@yahoo.com>
<br><b>To</b>: Leslie Meade; Kelemen Zoltan <keli@carocomp.ro>
<br><b>Cc</b>: cisco-voip@puck.nether.net <cisco-voip@puck.nether.net>
<br><b>Sent</b>: Tue Jul 08 01:50:12 2008<br><b>Subject</b>: Re: [cisco-voip] cme/PRI newbie question
<br></font></p>
<table cellspacing='0' cellpadding='0' border='0' ><tr><td valign='top' style='font: inherit;'>as he mentioned are they assigned to phones directly , i saw in the conf that u have assigned 1700 on line 2 , right ?<br><br>--- On <b>Tue, 7/8/08, Kelemen Zoltan <i><keli@carocomp.ro></i></b> wrote:<br><blockquote style="border-left: 2px solid rgb(16, 16, 255); margin-left: 5px; padding-left: 5px;">From: Kelemen Zoltan <keli@carocomp.ro><br>Subject: Re: [cisco-voip] cme/PRI newbie question<br>To: "Leslie Meade" <lmeade@signal.ca><br>Cc: cisco-voip@puck.nether.net<br>Date: Tuesday, July 8, 2008, 2:23 AM<br><br><pre>Are the incoming DiD numbers assigned to phones? Or transformed/routed <br>to them? Depending on how many digits you receive from the provider as <br>called number, you might need to do some number translations on the <br>called number to make sure the calls reach your phones.<br><br>As Erick noted, once you know your ISDN line is
up (Layer 2 Status <br>should include: State = MULTIPLE_FRAME_ESTABLISHED )<br>"debug isdn q931" is your friend ;-) As far as I'm concerned,<br>this <br>debug command has by far the most readable output of all Cisco IOS <br>debugs :-)<br><br>regards,<br> Zoltan<br><br>Erick Bergquist wrote:<br>> If you do a 'show isdn stat' on the router with PRI, does it say<br>MULTI<br>> FRAME ESTABLISHED?<br>><br>> If so, when you call the DIDs coming in on the new PRI, does 'debug<br>> isdn q931' show the call coming in?<br>><br>><br>> On Mon, Jul 7, 2008 at 11:44 PM, Leslie Meade <lmeade@signal.ca><br>wrote:<br>> <br>>> I might of explained it wrong. I have a 4 port FSO with 4 inbound<br>lines<br>>> that are all 1700.<br>>> I have a fractional PRI that has a pilot number of 1700 that is not<br>>> live, however the DiD's (that no one will use) are live.<br>>><br>>> Once the go ahead is given
the Telco will move the 1700 from the FXO<br>to<br>>> the PRI as its pilot number. At this time I get fast busy on the PRI<br>>> DID's. Is this normal or is my config incorrect?<br>>><br>>><br>>><br>>> -----Original Message-----<br>>> From: Jonathan Charles [mailto:jonvoip@gmail.com]<br>>> Sent: Monday, July 07, 2008 9:33 PM<br>>> To: Leslie Meade<br>>> Cc: cisco-voip@puck.nether.net<br>>> Subject: Re: [cisco-voip] cme/PRI newbie question<br>>><br>>> Well, they have made the pilot live, but it isn't hunting to the<br>other<br>>> FXO ports... so, once it is busy, the other calls fail. Open a ticket<br>>> with telco and tell them they are broken.<br>>><br>>><br>>> Jonathan<br>>><br>>> On Mon, Jul 7, 2008 at 11:23 PM, Leslie Meade <lmeade@signal.ca><br>wrote:<br>>> <br>>>> I have a four port FXO card and a new
fractional pri. The FXO has<br>a<br>>>> <br>>> four<br>>> <br>>>> line over lay of XXX XXXX 1700 that is being ported to my pri as<br>the<br>>>> <br>>> pilot<br>>> <br>>>> number.<br>>>><br>>>><br>>>><br>>>> My question, when I make an inbound call with one of the new<br>DID's.<br>>>> <br>>> The<br>>> <br>>>> phone rings and I get through. But if I try it again with another<br>>>> <br>>> phone to<br>>> <br>>>> the same number, while till on the first call I get busy signals.<br>I<br>>>> <br>>> have 15<br>>> <br>>>> phones all with have the same config as the one below. I have been<br>>>> <br>>> told that<br>>> <br>>>> when the pilot number has been made live I will not have
this<br>issue. I<br>>>> <br>>> this<br>>> <br>>>> true or am I missing something in my config to allow multiple<br>calls to<br>>>> <br>>> the<br>>> <br>>>> same number?<br>>>><br>>>> None of the DID's in the PRI will be used only the 1700 (pilot<br>number)<br>>>> <br>>> is<br>>> <br>>>> being used for incoming calls.<br>>>><br>>>><br>>>><br>>>> Leslie<br>>>><br>>>><br>>>><br>>>><br>>>><br>>>><br>>>><br>>>> _______________________________________________<br>>>> cisco-voip mailing list<br>>>> cisco-voip@puck.nether.net<br>>>> https://puck.nether.net/mailman/listinfo/cisco-voip<br>>>><br>>>><br>>>> <br>>>
_______________________________________________<br>>> cisco-voip mailing list<br>>> cisco-voip@puck.nether.net<br>>> https://puck.nether.net/mailman/listinfo/cisco-voip<br>>><br>>><br>>> <br>> _______________________________________________<br>> cisco-voip mailing list<br>> cisco-voip@puck.nether.net<br>> https://puck.nether.net/mailman/listinfo/cisco-voip<br>> <br><br>_______________________________________________<br>cisco-voip mailing list<br>cisco-voip@puck.nether.net<br>https://puck.nether.net/mailman/listinfo/cisco-voip</pre></blockquote></td></tr></table><br>