<br><font size=2 face="sans-serif">Ahh thank you for the reply. I
had changed it all back but didn't realize that because of those changes,
the port command on the dial-peers got removed. I got a phone call
this morning from the International site that all incoming/outgoing calls
were failing. :)</font>
<br><font size=2 face="sans-serif"><br>
Steve Siltman<br>
Assurant Corporate Technology<br>
Network Engineer - Cisco CCVP<br>
Work: 651-361-4752<br>
Cell: 651-336-5563<br>
steve.siltman@assurant.com</font>
<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td width=40%><font size=1 face="sans-serif"><b>keli@carocomp.ro</b> </font>
<p><font size=1 face="sans-serif">07/09/2008 05:55 PM</font>
<td width=59%>
<table width=100%>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">To</font></div>
<td><font size=1 face="sans-serif">steve.siltman@assurant.com</font>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">cc</font></div>
<td><font size=1 face="sans-serif">cisco-voip@puck.nether.net</font>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">Subject</font></div>
<td><font size=1 face="sans-serif">Re: [cisco-voip] Freeing up DSPs</font></table>
<br>
<table>
<tr valign=top>
<td>
<td></table>
<br></table>
<br>
<br>
<br><tt><font size=2>Hi Steve,<br>
<br>
The bad news is, what you saw in the sh in ser output is just what<br>
you're supposed to see on a voice E1, since that line is timeslots used<br>
for signaling (or data or something like that).<br>
<br>
I've just checked it with three different E1 lines I have around: a<br>
fractional voice E1, a full voice E1 and a data link. Both voice<br>
circuits show the same thing,<br>
... Timeslot(s) Used:16 ...<br>
the data circuit shows<br>
... Timeslot(s) Used:1-31 ...<br>
<br>
So this, by itself this is not a measure whether you have a full or a<br>
fractional E1 voice circuit.<br>
<br>
#sh isdn service should show you the channels in use, but that of course<br>
will show outofservice for those channels you removed from the<br>
configuration yourself.<br>
<br>
Since where I have fractional E1 I have it configured as such too, I'm<br>
not sure how it should show up if you have fractional from the provider,<br>
but configured it as a full E1.<br>
<br>
Also, shutting down 16 channels could be nasty, if you have full E1 and<br>
the provider is sending the calls in top-down channel order :)<br>
<br>
best regards,<br>
Zoltan<br>
<br>
steve.siltman@assurant.com wrote:<br>
><br>
> Hi All,<br>
><br>
> I noticed that a couple of our remote office routers Conference <br>
> Bridge profiles were unregistered with Call Manager. Taking
a <br>
> closer look, we are low on available DSP's. Doing a show interface
<br>
> ser 0/1/0:15 on our international voice circuit, the bottom of the
<br>
> display shows Timeslots(s) Used:16. Does this mean that this
is a <br>
> fractional E1? I have pri-group timeslots 1-31 configured on
the <br>
> controller E1.<br>
> I changed the pri-group timeslots to 1-16 and was able to register
<br>
> the Conference Bridge profile after the DSP's were freed up. Just
<br>
> wondering if I've taken away timeslots or not. Our documentation
on <br>
> the international sites doesn't show the voice circuit orders. I'm
<br>
> unable to tell how the circuit was ordered and how many timeslots.<br>
><br>
> Thanks,<br>
><br>
> Steve Siltman<br>
> Assurant Corporate Technology<br>
> Network Engineer - Cisco CCVP<br>
> Work: 651-361-4752<br>
> Cell: 651-336-5563<br>
> steve.siltman@assurant.com<br>
</font></tt>
<br>
<P>
<HR>
This e-mail message and all attachments transmitted with it may contain legally
privileged and/or confidential information intended solely for the use of the
addressee(s). If the reader of this message is not the intended recipient, you
are hereby notified that any reading, dissemination, distribution, copying,
forwarding or other use of this message or its attachments is strictly
prohibited. If you have received this message in error, please notify the sender
immediately and delete this message and all copies and backups thereof.</P>
<P>Thank you.<BR>
<HR>
<P></P>