<HTML>
<HEAD>
<TITLE>Re: [cisco-voip] VoIP over Hardware VPN</TITLE>
</HEAD>
<BODY>
<FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'>The phone is sitting here in my house and I can ping it from my computer at my house. I can do an extension to extension call and leave voicemail which goes through. However, if I do an extension to extension call or make an outside call from or to the IP phone via the telco then I see no rx traffic. Thank You...<BR>
<BR>
<BR>
On 5/28/09 6:11 PM, "Craig Staffin" <craig@staffin.org> wrote:<BR>
<BR>
</SPAN></FONT><BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'>Jim,<BR>
<BR>
Keep in mind that the RTP traffic does not flow from phone to CUCM to phone. So you would actually need to make sure you can ping the phone from your hours and vise versa.<BR>
<BR>
Craig<BR>
<BR>
<BR>
On Thu, May 28, 2009 at 7:05 PM, Jim Reed <<FONT COLOR="#0000FF"><U>jreed@swiftnews.com</U></FONT>> wrote:<BR>
</SPAN></FONT><BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><FONT SIZE="4"><SPAN STYLE='font-size:14.0px'><B>Okay, hate to be a pain but the phone is registered and when I call one of our main locations and enter the extension the phone rings at my house but am getting no voice on my end. Seeing tx traffic on the phone statistics but no rx traffic. Any thoughts? Routing all seems to be in place. I can ping the phone from the Call Manager and can ping the Call Manager from my home. Have the phone in the same calling search space, location, etc., as the Call Manager it’s registering to. It’s showing a g711 codec.<BR>
<BR>
Thanks in advance for any advice...<BR>
</B></SPAN></FONT><FONT SIZE="2"><SPAN STYLE='font-size:10.0px'>-- <BR>
Jim Reed<BR>
Technology Wrangler<BR>
Swift Communications, Inc.<BR>
970-683-5646 (Direct)<BR>
970-683-5650 (Fax)<BR>
<BR>
</SPAN></FONT><SPAN STYLE='font-size:12.0px'><BR>
On 5/28/09 3:48 PM, "Wes Sisk" <<FONT COLOR="#0000FF"><U>wsisk@cisco.com</U></FONT>> wrote:<BR>
<BR>
</SPAN></FONT><BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'>It depends on your setup. If you are doing address translation then you must have it enabled.<BR>
<BR>
If you are not doing address translation and do not dynamic port allocation (basically if you have permit ip any any) then you need to have it disabled.<BR>
<BR>
So, engineer's favorite answer - it depends.<BR>
<BR>
/Wes<BR>
<BR>
On Thursday, May 28, 2009 3:56:48 PM, Jim Reed <<FONT COLOR="#0000FF"><U>jreed@swiftnews.com</U></FONT>> <<FONT COLOR="#0000FF"><U><a href="mailto:jreed@swiftnews.com">mailto:jreed@swiftnews.com</a></U></FONT>> wrote:<BR>
</SPAN></FONT><BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'> Re: [cisco-voip] VoIP over Hardware VPN </SPAN><FONT SIZE="4"><SPAN STYLE='font-size:14.0px'><B>Thanks, Lelio.<BR>
Are you referring to turning it on or turning it off!<BR>
</B></SPAN></FONT><FONT SIZE="2"><SPAN STYLE='font-size:10.0px'>-- <BR>
Jim Reed<BR>
Swift Communications, Inc.<BR>
970-683-5646 (Direct)<BR>
775-772-7666 (Cell)<BR>
<BR>
<BR>
</SPAN></FONT><SPAN STYLE='font-size:12.0px'> <BR>
On 5/28/09 1:55 PM, "Lelio Fulgenzi" <<FONT COLOR="#0000FF"><U>lelio@uoguelph.ca</U></FONT>> <<FONT COLOR="#0000FF"><U><a href="mailto:lelio@uoguelph.ca">mailto:lelio@uoguelph.ca</a></U></FONT>> wrote:<BR>
<BR>
<BR>
</SPAN></FONT><BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'>I think the biggest thing is "sccp fixup"....<BR>
<BR>
---<BR>
Lelio Fulgenzi, B.A.<BR>
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1<BR>
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)<BR>
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^<BR>
"Bad grammar makes me [sic]" - Tshirt<BR>
<BR>
<BR>
----- Original Message -----<BR>
From: "Jim Reed" <<FONT COLOR="#0000FF"><U>jreed@swiftnews.com</U></FONT>> <<FONT COLOR="#0000FF"><U><a href="mailto:jreed@swiftnews.com">mailto:jreed@swiftnews.com</a></U></FONT>> <BR>
To: <FONT COLOR="#0000FF"><U>cisco-voip@puck.nether.net</U></FONT>, <FONT COLOR="#0000FF"><U>ask-icd-ivr-support@external.cisco.com<BR>
</U></FONT>Sent: Thursday, May 28, 2009 3:44:45 PM GMT -05:00 US/Canada Eastern<BR>
Subject: [cisco-voip] VoIP over Hardware VPN<BR>
<BR>
VoIP over Hardware VPN </SPAN><FONT SIZE="4"><SPAN STYLE='font-size:14.0px'><B>Anyone have any hints, tips, suggestions, comments, concerns, etc., regarding running a single IP phone over a hardware-to-hardware VPN. I've tried it in the past but could only seem to get voice going in one direction. It's been a while and I'm going to give it another shot. Will be working with ASA 5505 on one and ASA 5510 on the other. Call Manager 4.x. Probably a 7940 or 7960 phone. Internet connections are 15-Meg-Over-Ethernet on one end and 10-Meg-Over-Ethernet on the other. Current ping times between devices on the two ends are consistently very fast -- less than 100ms over extended ping tests.<BR>
<BR>
Any advice, anecdotal wisdom, personal experience, etc., that anyone has had in trying to do this is sincerely welcome and appreciated.<BR>
<BR>
Thank You...<BR>
<BR>
</B></SPAN></FONT></FONT></BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'> <BR>
</SPAN><FONT SIZE="2"><SPAN STYLE='font-size:10.0px'> </SPAN></FONT><SPAN STYLE='font-size:12.0px'> <BR>
<BR>
<BR>
<BR>
_______________________________________________<BR>
cisco-voip mailing list<BR>
<FONT COLOR="#0000FF"><U>cisco-voip@puck.nether.net<BR>
https://puck.nether.net/mailman/listinfo/cisco-voip<BR>
</U></FONT> <BR>
</SPAN></FONT></BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'><BR>
<BR>
</SPAN></FONT></BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'><BR>
<BR>
<BR>
_______________________________________________<BR>
cisco-voip mailing list<BR>
<FONT COLOR="#0000FF"><U>cisco-voip@puck.nether.net<BR>
https://puck.nether.net/mailman/listinfo/cisco-voip<BR>
</U></FONT><BR>
</SPAN></FONT></BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'><BR>
<BR>
</SPAN></FONT></BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'><BR>
<BR>
-- <BR>
Jim Reed<BR>
Technology Wrangler<BR>
Swift Communications, Inc.<BR>
970-683-5646 (Direct)<BR>
970-683-5650 (Fax)<BR>
<BR>
</SPAN></FONT>
</BODY>
</HTML>