Hi all,<br><br>I've managed to update the firmware of the device. I was not able to see the document which Nikhil referred because of privileges. I've found a similiar topic on the net but it describes the Nokia configuration.<br>
<br><a href="http://snippets101.blogspot.com/2008/08/cisco-and-nokia-dual-mode-part-iv-sip.html">http://snippets101.blogspot.com/2008/08/cisco-and-nokia-dual-mode-part-iv-sip.html</a><br><br>is there any possibility that one can send me the original document which Cisco published?<br>
<br>Thanks in Advance.<br><br>CEM<br><br><div class="gmail_quote">On Wed, Jun 17, 2009 at 12:34 AM, Phansalkar Nikhil <span dir="ltr"><<a href="mailto:nsphansa@yahoo.com">nsphansa@yahoo.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
<div><div style="font-family: times new roman,new york,times,serif; font-size: 12pt;"><div>Since it uses SIP, you can try adding the ATA as a third party SIP phone to the CUCM.<br><br>The CUCM configuration steps are documented at:<br>
<span><a href="http://www.cisco.com/en/US/customer/docs/voice_ip_comm/cucm/admin/6_0_1/ccmcfg/b09sip3p.html" target="_blank">http://www.cisco.com/en/US/customer/docs/voice_ip_comm/cucm/admin/6_0_1/ccmcfg/b09sip3p.html</a></span><br>
<br>I recently helped somebody add a Linksys PAP2 (which is an ATA) as a SIP endpoint using the above steps and it worked.<br><br>Cheers,<br>Nikhil<br><br></div><div style="font-family: times new roman,new york,times,serif; font-size: 12pt;">
<br><div style="font-family: arial,helvetica,sans-serif; font-size: 13px;"><font size="2" face="Tahoma"><hr size="1"><b><span style="font-weight: bold;">From:</span></b> Paul
<<a href="mailto:asobihoudai@yahoo.com" target="_blank">asobihoudai@yahoo.com</a>><br><b><span style="font-weight: bold;">To:</span></b> cem caglayan <<a href="mailto:cem.caglayan@gmail.com" target="_blank">cem.caglayan@gmail.com</a>>; <a href="mailto:cisco-voip@puck.nether.net" target="_blank">cisco-voip@puck.nether.net</a><br>
<b><span style="font-weight: bold;">Sent:</span></b> Tuesday, June 16, 2009 8:36:33 AM<br><b><span style="font-weight: bold;">Subject:</span></b> Re: [cisco-voip] About Grandstream HT502 ATA device and usability with CUCM 6.0<br>
</font><div><div></div><div class="h5"><br>
<br>Did you read the HT502 manual already?<br><span><a href="http://tinyurl.com/lyvgb2" target="_blank">http://tinyurl.com/lyvgb2</a></span><br><br>Apparently it only supports SIP for signaling.<br><br>You can't use CCM TFTP for its firmware so you'll have to upgrade it manually if necessary.<br>
<br>You'll then have to turn it into a SIP UA that can talk to the SIP components under CCM6.<br><br><br>________________________________<br>From: cem caglayan <<a href="mailto:cem.caglayan@gmail.com" target="_blank">cem.caglayan@gmail.com</a>><br>
To: <a href="mailto:cisco-voip@puck.nether.net" target="_blank">cisco-voip@puck.nether.net</a><br>Sent: Tuesday, June 16, 2009 1:33:50 AM<br>Subject: [cisco-voip] About Grandstream HT502 ATA device and usability with CUCM 6.0<br>
<br>Hi all,<br><br>Here is the deal, i have a grandstream ht502 ATA device<br>in my hand, is there any way to implement this device to
CUCM 6.0 to<br>make analog phones getting used???<br><br>I've googled and could not find any related document.<br><br>Help will be appreciated.<br><br>Thanks in advance...<br><br><br> <br><br></div></div>_______________________________________________<br>
cisco-voip mailing list<div class="im"><br><a href="mailto:cisco-voip@puck.nether.net" target="_blank">cisco-voip@puck.nether.net</a><br></div><a href="https://puck.nether.net/mailman/listinfo/cisco-voip" target="_blank">https://puck.nether.net/mailman/listinfo/cisco-voip</a><br>
</div></div></div><br>
</div></blockquote></div><br>