What type of circuit are you trying to connect to?<br><br>Key difference as you stated is the ability to do unframed on G703 cards.<br><br>The G703 cards also support being configured the same as the T1/E1 cards.. so they have added flexibility in that regard, and if you are unsure of your circuit you can buy the G703 cards to hedge your bets!<br>
<br>Cheers,<br><br>Tim.<br><br><div class="gmail_quote">On Fri, Jul 24, 2009 at 8:23 PM, Syed Khalid Ali <span dir="ltr"><<a href="mailto:syed.khalid.khursheed@gmail.com">syed.khalid.khursheed@gmail.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">No G703 card still need a modem. What I understood that in case of T1<br>
there is no need of an external CSU/DSU. with E1 it still requires an<br>
E1 modem<br>
<br>
By unframed means that the whole 2.04mb can be used; that is all time<br>
slots are available.<br>
<br>
G703 are not EOS/EOL<br>
<div><div></div><div class="h5"><br>
On Fri, Jul 24, 2009 at 2:17 PM, Moataz Mamdouh<<a href="mailto:moataz_mmdh@yahoo.com">moataz_mmdh@yahoo.com</a>> wrote:<br>
><br>
> so u mean that G.703 card doesn 't need a modem , the Teleco Cable will be<br>
> directly connected to the router.<br>
><br>
> what do u mean about unframed ? u don't have the time slot command under the<br>
> controller !!!<br>
> i can't see any difference between both cards ( is G.703 card are EOS ? ) as<br>
> they are supported only on 26xx and 36xx not ISR.<br>
><br>
> --- On Fri, 7/24/09, Syed Khalid Ali <<a href="mailto:syed.khalid.khursheed@gmail.com">syed.khalid.khursheed@gmail.com</a>><br>
> wrote:<br>
><br>
> From: Syed Khalid Ali <<a href="mailto:syed.khalid.khursheed@gmail.com">syed.khalid.khursheed@gmail.com</a>><br>
> Subject: Re: [cisco-voip] VIC2-1MFT-G703 and VIC2-1MFT-T1/E1<br>
> To: "Moataz Mamdouh" <<a href="mailto:moataz_mmdh@yahoo.com">moataz_mmdh@yahoo.com</a>>, <a href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a><br>
> Date: Friday, July 24, 2009, 5:07 AM<br>
><br>
> After reading the data sheets I was able to put out theses<br>
> differences. Can any one validate!<br>
><br>
> MFT-T1/E1 does framed E1 (31 timeslots @ 64 Kbps) and fractional (n<31<br>
> timeslots @ 64 Kbps) and T1 support.<br>
> MFT-G703 additionally does unframed (2048 Kbps) and no T1 support.<br>
> Both support the dedicated echo cancellation daughter module EC-MFT-32 or<br>
> 64.<br>
> With MFT-T1/E1 there is no need for external CSU/DSU when used as a T1<br>
> module.<br>
> Drop and Insert capability.<br>
> Supported in 1841 and higher ISR series routers.<br>
> Supported with 2600, 2600XM, 2691, 3660, 3700 and higher models.<br>
><br>
> The NM-xCE1T1-PRI does not support dedicated echo-cancellation card.<br>
> Supports with framed and unframed E1 signaling no need for another G.703<br>
> card.<br>
> No Multiflex operation.<br>
> Compatible with supported V.92 modems.<br>
> Supports (native) termination of balanced (coaxial) cable.<br>
> Simultaneous support of T1 and E1 operation on the same NM-module.<br>
> Supported in 2600XM and onwards.<br>
> Online insertion and removal (OIR) supported on Cisco 3660, 3745 and<br>
> 3845 routers.<br>
> On-board expansion slot for future usage.<br>
><br>
> One thing that still confuses me that in case of VWIC2-2MFT-T1/E1 can<br>
> one port act as a T1 and other as E1.<br>
><br>
> Any other thing that someone wants to add!!!<br>
><br>
><br>
><br>
> On Fri, Jul 24, 2009 at 1:49 PM, Moataz Mamdouh<<a href="mailto:moataz_mmdh@yahoo.com">moataz_mmdh@yahoo.com</a>><br>
> wrote:<br>
>> I am not sure but i think they are the same , because G.703 is ITU<br>
>> standard<br>
>> for voice and data over T1 and E1<br>
>><br>
>><br>
>> --- On Thu, 7/23/09, Syed Khalid Ali <<a href="mailto:syed.khalid.khursheed@gmail.com">syed.khalid.khursheed@gmail.com</a>><br>
>> wrote:<br>
>><br>
>> From: Syed Khalid Ali <<a href="mailto:syed.khalid.khursheed@gmail.com">syed.khalid.khursheed@gmail.com</a>><br>
>> Subject: [cisco-voip] VIC2-1MFT-G703 and VIC2-1MFT-T1/E1<br>
>> To: <a href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a><br>
>> Date: Thursday, July 23, 2009, 12:59 PM<br>
>><br>
>> what is the difference between G.703 and T1/E1 card beside support for<br>
>> T1 in later one?<br>
>> Also how can we compare these with NM-1CE1T1-PR. any thing special to<br>
>> consider before going to ordering???<br>
>><br>
>> --<br>
>> Thanks,<br>
>> Syed Khalid Ali<br>
>> _______________________________________________<br>
>> cisco-voip mailing list<br>
>> <a href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a><br>
>> <a href="https://puck.nether.net/mailman/listinfo/cisco-voip" target="_blank">https://puck.nether.net/mailman/listinfo/cisco-voip</a><br>
>><br>
>><br>
><br>
><br>
><br>
> --<br>
> Thanks,<br>
> Syed Khalid Ali<br>
><br>
><br>
<br>
<br>
<br>
</div></div>--<br>
<div><div></div><div class="h5">Thanks,<br>
Syed Khalid Ali<br>
_______________________________________________<br>
cisco-voip mailing list<br>
<a href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a><br>
<a href="https://puck.nether.net/mailman/listinfo/cisco-voip" target="_blank">https://puck.nether.net/mailman/listinfo/cisco-voip</a><br>
</div></div></blockquote></div><br>