<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=iso-8859-1">
<META content="MSHTML 6.00.6000.16890" name=GENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY>
<DIV><FONT face=Arial size=2>Also, if I dump the show dialplan information for
dialpeer 93876800 there is no outbound application listed. Is this normal, or
should it be something, like at least "DEFAULT" as appears for the in bound
application?</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face="Courier New" size=2>voiptrunks#show dialplan number
93876800<BR>Macro Exp.: 93876800</FONT></DIV>
<DIV><FONT face="Courier New" size=2></FONT> </DIV>
<DIV><FONT face="Courier New"
size=2>VoiceEncapPeer3876800<BR> peer
type = voice, information type =
voice,<BR> description =
`',<BR> tag = 3876800,
destination-pattern = `93876800',<BR>
answer-address = `', preference=0,<BR>
CLID Restriction = None<BR> CLID
Network Number = `'<BR> CLID Second
Number sent<BR> source carrier-id =
`', target carrier-id = `',<BR> source
trunk-group-label = `', target trunk-group-label =
`',<BR> numbering Type =
`unknown'<BR> group = 3876800, Admin
state is up, Operation state is
up,<BR> incoming called-number = `',
connections/maximum = 0/unlimited,<BR>
DTMF Relay = disabled,<BR> huntstop =
disabled,<BR><FONT color=#ff0000> in
bound application associated:
'DEFAULT'<BR> out bound application
associated: ''<BR></FONT> dnis-map
=<BR> permission
:both<BR> incoming COR list:maximum
capability<BR> outgoing COR
list:minimum requirement<BR>
Translation profile (Incoming):<BR>
Translation profile
(Outgoing):ninestrip<BR> incoming call
blocking:<BR> translation-profile =
`'<BR> disconnect-cause =
`no-service'<BR> type = pots, prefix =
`',<BR> forward-digits
default<BR> session-target = `',
voice-port = `1/1:D',<BR>
direct-inward-dial = disabled,<BR>
digit_strip = enabled,<BR> register
E.164 number with GK = TRUE<BR> fax
rate = system, payload size = 20 bytes</FONT></DIV>
<DIV><FONT face="Courier New" size=2></FONT> </DIV>
<DIV><FONT face="Courier New" size=2>
Time elapsed since last clearing of voice call statistics
never<BR> Connect Time = 0, Charged
Units = 0,<BR> Successful Calls = 0,
Failed Calls = 0, Incomplete Calls =
0<BR> Accepted Calls = 0, Refused
Calls = 0,<BR> Last Disconnect Cause
is "",<BR> Last Disconnect Text is
"",<BR> Last Setup Time =
0.<BR>Matched: 93876800 Digits: 8<BR>Target:</FONT></DIV>
<DIV><FONT face="Courier New" size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>voiptrunks#<BR></FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>----- Original Message ----- </FONT>
<DIV><FONT face=Arial size=2>From: "Joseph Mays" <</FONT><A
href="mailto:mays@win.net"><FONT face=Arial size=2>mays@win.net</FONT></A><FONT
face=Arial size=2>></FONT></DIV>
<DIV><FONT face=Arial size=2>To: "Joseph Mays" <</FONT><A
href="mailto:mays@win.net"><FONT face=Arial size=2>mays@win.net</FONT></A><FONT
face=Arial size=2>>; <</FONT><A
href="mailto:cisco-nas@puck.nether.net"><FONT face=Arial
size=2>cisco-nas@puck.nether.net</FONT></A><FONT face=Arial size=2>>;
<</FONT><A href="mailto:cisco-voip@puck.nether.net"><FONT face=Arial
size=2>cisco-voip@puck.nether.net</FONT></A><FONT face=Arial
size=2>></FONT></DIV>
<DIV><FONT face=Arial size=2>Sent: Wednesday, August 12, 2009 3:50
PM</FONT></DIV>
<DIV><FONT face=Arial size=2>Subject: Re: [cisco-voip] Cisco 5400 Outdialing
problem.</FONT></DIV></DIV>
<DIV><FONT face=Arial><BR><FONT size=2></FONT></FONT></DIV><FONT face=Arial
size=2>> In the simplest sense, is there a way to tell the cisco to generate
a call <BR>> from the command line out a specific
port?<BR>></FONT></BODY></HTML>