<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=us-ascii">
<META content="MSHTML 6.00.6000.16890" name=GENERATOR></HEAD>
<BODY>
<DIV dir=ltr align=left><SPAN class=357101818-12102009><FONT face="Trebuchet MS"
color=#000080 size=2>You should be able to define another queue-set, and then
assign that interface to it. I don't remember the details, as I used
AutoQoS on my 3750's for the phones. </FONT></SPAN></DIV>
<DIV dir=ltr align=left><SPAN class=357101818-12102009><FONT face="Trebuchet MS"
color=#000080 size=2></FONT></SPAN> </DIV>
<DIV dir=ltr align=left><SPAN class=357101818-12102009><FONT face="Trebuchet MS"
color=#000080 size=2>I would probably move the connection to a router if you
have one. Easier in my opinion.</FONT></SPAN></DIV>
<DIV dir=ltr align=left><SPAN class=357101818-12102009><FONT face="Trebuchet MS"
color=#000080 size=2></FONT></SPAN> </DIV>
<DIV dir=ltr align=left><SPAN class=357101818-12102009><FONT face="Trebuchet MS"
color=#000080 size=2>------for your switch if you leave the connection
there. This is a base start, you will have to read up of 3750 QoS to make
sure you configure the other queue set properly------</FONT></SPAN></DIV>
<DIV dir=ltr align=left><SPAN class=357101818-12102009><FONT face="Trebuchet MS"
color=#000080 size=2></FONT></SPAN> </DIV>
<DIV dir=ltr align=left><SPAN class=357101818-12102009><FONT face="Trebuchet MS"
color=#000080 size=2>switch(config)#mls qos queue-set output 2
........</FONT></SPAN></DIV>
<DIV dir=ltr align=left><SPAN class=357101818-12102009><FONT face="Trebuchet MS"
color=#000080 size=2>(You would have a lot of commands under this based
command... see <A
href="http://www.cisco.com/en/US/products/hw/switches/ps5023/products_tech_note09186a0080883f9e.shtml#topic3">http://www.cisco.com/en/US/products/hw/switches/ps5023/products_tech_note09186a0080883f9e.shtml#topic3</A>)</FONT></SPAN></DIV>
<DIV dir=ltr align=left><SPAN class=357101818-12102009><SPAN
class=357101818-12102009><FONT face="Trebuchet MS" color=#000080
size=2></FONT></SPAN></SPAN> </DIV>
<DIV dir=ltr align=left><SPAN class=357101818-12102009><SPAN
class=357101818-12102009><FONT face="Trebuchet MS" color=#000080
size=2>switch(config-if)#priority queue out (enables the uses of queue 2 as the
LLQ queue)</FONT></SPAN></SPAN></DIV>
<DIV dir=ltr align=left><SPAN class=357101818-12102009><FONT face="Trebuchet MS"
color=#000080 size=2>switch(config-if)#queue-set 2 (This assigns your port
to the second queue set) </FONT></SPAN></DIV><BR>
<DIV class=OutlookMessageHeader lang=en-us dir=ltr align=left>
<HR tabIndex=-1>
<FONT face=Tahoma size=2><B>From:</B> Kevin Dunn [mailto:cheesevoice@gmail.com]
<BR><B>Sent:</B> Monday, October 12, 2009 2:15 PM<BR><B>To:</B> Brantley
Richbourg<BR><B>Cc:</B> Cisco Voice<BR><B>Subject:</B> Re: [cisco-voip] QoS for
Day to Day traffic<BR></FONT><BR></DIV>
<DIV></DIV>
<DIV>well there is no need to police, I actually want day to day traffic to be
able to creep into the DR area if it isn't being used, SAN to SAN is suppose to
take place "off hours" so that leaves more bandwidth for my users to flood the
network drives with MP3 files and porn.</DIV>
<DIV> </DIV>
<DIV>(I kid becuase it eases the pain)</DIV>
<DIV> </DIV>
<DIV>I set up the remote router and looks like we are a go on the old
2851....but wait the snags continue....on the other end they have the WAN
ethernet in a 3750 stack....*sigh* okay so here is the big question, I can set
cos-dscp map but the queue bandwidth is defined in AutoQos, can I define a
second set for this interface? So the EF queue gets 3%??</DIV>
<DIV> </DIV>
<DIV>Other than moving the fiber to a router, any suggestions?</DIV>
<DIV> </DIV>
<DIV><BR><BR> </DIV>
<DIV class=gmail_quote>On Mon, Oct 12, 2009 at 12:40 PM, Brantley Richbourg
<SPAN dir=ltr><<A
href="mailto:Brantley.Richbourg@mmicnc.com">Brantley.Richbourg@mmicnc.com</A>></SPAN>
wrote:<BR>
<BLOCKQUOTE class=gmail_quote
style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid">
<DIV>
<DIV dir=ltr align=left><SPAN><FONT face="Trebuchet MS" color=#000080
size=2>Another thought too is do you want to make sure your day2day traffic
does not impact your default class (meaning your DR traffic)? If yes, I
would add police statements to your policy-map to keep traffic
at 8Mbps, 89Mbps, etc. CBWFQ will only really kick in when there is
congestion on your interface. So your day-to-day traffic could kick it
up to 100Mbps if there is no traffic for the other classes at that time.
</FONT></SPAN></DIV>
<DIV dir=ltr align=left><SPAN><FONT face="Trebuchet MS" color=#000080
size=2></FONT></SPAN> </DIV>
<DIV dir=ltr align=left><SPAN><FONT face="Trebuchet MS" color=#000080
size=2>If you want to make sure DR traffic always stays at 89%, etc,
etc,. I would modify your policy-map to the
following:</FONT></SPAN></DIV>
<DIV class=im>
<DIV dir=ltr align=left><SPAN><FONT face="Trebuchet MS" color=#000080
size=2></FONT></SPAN> </DIV>
<DIV dir=ltr align=left><SPAN><FONT face="Trebuchet MS" color=#000080
size=2></FONT></SPAN> </DIV>
<DIV dir=ltr align=left><FONT size=2><FONT color=#000080><FONT
face="Trebuchet MS"><STRONG>policy-map
DRandVoice</STRONG><BR> <STRONG>class voice</STRONG><BR> priority
percent <SPAN>3</SPAN></FONT></FONT></FONT></DIV>
<DIV dir=ltr align=left><FONT face="Trebuchet MS" color=#000080
size=2> <STRONG>class day2day<BR></STRONG> bandwidth percent
8</FONT></DIV></DIV>
<DIV dir=ltr align=left><SPAN><FONT face="Trebuchet MS" color=#000080
size=2> police rate percent 8</FONT></SPAN></DIV>
<DIV dir=ltr align=left><SPAN> <FONT
face="Trebuchet MS" color=#000080><FONT size=2>conform-action
transmit<BR> exceed-action
drop<BR> violate-action
drop</FONT></FONT></SPAN></DIV>
<DIV dir=ltr align=left><SPAN><FONT face="Trebuchet MS" color=#000080><FONT
size=2> <STRONG>class class-default</STRONG></FONT></FONT></SPAN></DIV>
<DIV dir=ltr align=left><SPAN><FONT face="Trebuchet MS"
color=#000080> <FONT size=2>police rate percent 89</FONT>
<DIV dir=ltr align=left><SPAN> <FONT size=2>
</FONT><FONT face="Trebuchet MS" color=#000080><FONT size=2>conform-action
transmit<BR> exceed-action
drop<BR> violate-action
drop</FONT></FONT></SPAN></DIV><BR><FONT size=2>priority queueing will
automatically police at 3%.</FONT></FONT></SPAN></DIV><BR>
<DIV lang=en-us dir=ltr align=left>
<HR>
<FONT face=Tahoma size=2><B>From:</B> Kevin Dunn [mailto:<A
href="mailto:cheesevoice@gmail.com" target=_blank>cheesevoice@gmail.com</A>]
<BR><B>Sent:</B> Monday, October 12, 2009 12:15 PM<BR><B>To:</B> Brantley
Richbourg<BR><B>Cc:</B> Cisco Voice<BR><B>Subject:</B> Re: [cisco-voip] QoS
for Day to Day traffic<BR></FONT><BR></DIV>
<DIV>
<DIV></DIV>
<DIV class=h5>
<DIV></DIV>
<DIV>AHHHHHHH (light bulb moment)</DIV>
<DIV> </DIV>
<DIV>by matching ACL 101 I am putting everything BUT 10.31.0.0 traffic in the
day2day class, and then everythign else would be in default class...
very awesome.</DIV>
<DIV> </DIV>
<DIV>and THAT is why I ask, because sometimes, you just don't think the way
everyone else does.</DIV>
<DIV> </DIV>
<DIV>Thank you all very much.</DIV>
<DIV> </DIV>
<DIV>Kevin<BR><BR></DIV>
<DIV class=gmail_quote>On Mon, Oct 12, 2009 at 11:05 AM, Brantley Richbourg
<SPAN dir=ltr><<A href="mailto:Brantley.Richbourg@mmicnc.com"
target=_blank>Brantley.Richbourg@mmicnc.com</A>></SPAN> wrote:<BR>
<BLOCKQUOTE class=gmail_quote
style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid">
<DIV>
<DIV dir=ltr align=left><FONT face="Trebuchet MS" color=#000080
size=2><SPAN>Hello,</SPAN></FONT></DIV>
<DIV dir=ltr align=left><FONT face="Trebuchet MS" color=#000080
size=2><SPAN></SPAN></FONT> </DIV>
<DIV dir=ltr align=left><FONT face="Trebuchet MS" color=#000080
size=2><SPAN>I have some thoughts on your policy-map.</SPAN></FONT></DIV>
<DIV dir=ltr align=left><FONT face="Trebuchet MS" color=#000080
size=2><SPAN></SPAN></FONT> </DIV>
<DIV dir=ltr align=left><FONT face="Trebuchet MS" color=#000080
size=2><SPAN>You are not going to get 8 Mbps on your day2day class.
First off, you give 3% priority to voice, which leaves 97Mbps
remaining. The next class in your policy-map (DR) is saying
to use 89% of the <EM>remaining</EM> 97Mbps (84.39Mbps), and finally you
have day2day traffic can have 8% of the <EM>remaining</EM> BW. So your
DR replication I assume will be using a good bit of bandwidth all day long,
so you are only going to get 157Kbps for DR traffic (if DR and Voice are
using 100% of what they can get), because the "remaining" keyword tells the
IOS to allocate that percentage of bandwidth that has <EM>not</EM> been
allocated to other classes. I would do this:</SPAN></FONT></DIV>
<DIV dir=ltr align=left><FONT face="Trebuchet MS" color=#000080
size=2><SPAN></SPAN></FONT> </DIV>
<DIV dir=ltr align=left><FONT face="Trebuchet MS"><SPAN>
<DIV><FONT face=Arial color=#000080 size=2>
<DIV>policy-map DRandVoice<BR> class voice<BR> priority percent
3<BR></DIV> class day2day<BR> bandwidth percent
8</FONT></DIV>
<DIV><FONT face=Arial color=#000080 size=2></FONT> </DIV>
<DIV><SPAN><FONT color=#000080 size=2>Your DR traffic will hit the
"class-default" will be get the rest of the pipe if both classes are being
matched on. That will give you 89% for DR, 8% for day2day and 3% for
voice (LLQ).</FONT></SPAN></DIV>
<DIV><SPAN><FONT color=#000080 size=2></FONT></SPAN> </DIV>
<DIV><SPAN><FONT color=#000080 size=2>More information here: <A
href="http://www.cisco.com/en/US/tech/tk543/tk757/technologies_tech_note09186a0080103eae.shtml#summaryofdifferences"
target=_blank>http://www.cisco.com/en/US/tech/tk543/tk757/technologies_tech_note09186a0080103eae.shtml#summaryofdifferences</A></FONT></SPAN></DIV>
<DIV><SPAN><FONT color=#000080 size=2></FONT></SPAN> </DIV>
<DIV><SPAN><FONT color=#000080 size=2>Thanks,</FONT></SPAN></DIV>
<DIV><SPAN><FONT color=#000080 size=2></FONT></SPAN> </DIV>
<DIV><SPAN><FONT color=#000080 size=2>Brantley</FONT></SPAN></DIV>
<DIV><SPAN><FONT color=#000080 size=2></FONT></SPAN> </DIV>
<DIV><SPAN>
<DIV align=left>
<DIV dir=ltr>
<DIV align=left><FONT face=Calibri color=#1e66b7 size=2><STRONG>Brantley
Richbourg, MCSE, CCNAS, VCP</STRONG></FONT></DIV>
<DIV align=left><FONT face=Calibri color=#1e66b7 size=2>Network
Engineer</FONT></DIV>
<DIV><FONT face=Calibri color=#1e66b7 size=2>Medical Mutual Insurance
Company of North Carolina</FONT></DIV>
<DIV><FONT face=Calibri color=#1e66b7 size=2>919.878.7564 </FONT></DIV>
<DIV><FONT face=Calibri color=#1e66b7 size=2>919.878.7550 (F)</FONT></DIV>
<DIV><FONT face=Calibri color=#1e66b7 size=2><A
href="mailto:Brantley.Richbourg@mmicnc.com"
target=_blank>Brantley.Richbourg@mmicnc.com</A></FONT></DIV>
<DIV><FONT face=Calibri color=#1e66b7 size=2><A
href="http://www.medicalmutualgroup.com/"
target=_blank>www.medicalmutualgroup.com</A></FONT></DIV></DIV></DIV></SPAN></DIV></SPAN></FONT></DIV>
<DIV dir=ltr align=left><FONT face="Trebuchet MS" color=#000080
size=2><SPAN> </SPAN></FONT></DIV><BR>
<DIV lang=en-us dir=ltr align=left>
<HR>
<FONT face=Tahoma size=2><B>From:</B> <A
href="mailto:cisco-voip-bounces@puck.nether.net"
target=_blank>cisco-voip-bounces@puck.nether.net</A> [mailto:<A
href="mailto:cisco-voip-bounces@puck.nether.net"
target=_blank>cisco-voip-bounces@puck.nether.net</A>] <B>On Behalf Of
</B>Kevin Dunn<BR><B>Sent:</B> Monday, October 12, 2009 10:41
AM<BR><B>To:</B> Cisco Voice
<DIV><BR><B>Subject:</B> [cisco-voip] QoS for Day to Day
traffic<BR></DIV></FONT><BR></DIV>
<DIV>
<DIV></DIV>
<DIV>
<DIV></DIV>
<DIV class=gmail_quote>
<DIV>
<DIV>Hello my Pundits</DIV>
<DIV><SPAN><FONT face=Arial></FONT></SPAN> </DIV>
<DIV><SPAN><FONT face=Arial>I have a 100Meg Ethernet WAN connection between
two towns for DR purposes, and we are going to run "day to day" traffic
(voice and data) over this circuit as well, now when replication and SAN to
SAN traffic hits I don't want it to mess with the "day to day"
traffic. The DR traffic will either source or destination to
10.31.0.0. So I made a couple of ACL's to match that IP to. The
end result is I want to voice traffic to have priority and 3Megs of
bandwidth, Day to Day traffic around 8 Megs of traffic and DR (San to San)
the remaining 89%.... </FONT></SPAN></DIV>
<DIV><SPAN><FONT face=Arial></FONT></SPAN> </DIV>
<DIV><SPAN><FONT face=Arial>1. Do you think this will
work?</FONT></SPAN></DIV>
<DIV><SPAN><FONT face=Arial>2. Do you think it is set up
right?</FONT></SPAN></DIV>
<DIV><SPAN><FONT face=Arial></FONT></SPAN> </DIV>
<DIV><SPAN><FONT face=Arial></FONT></SPAN> </DIV>
<DIV><FONT face=Arial></FONT> </DIV>
<DIV><FONT face=Arial>class-map match-any voice<BR> match dscp ef
<BR> match protocol rtp audio <BR>class-map match-any DR<BR> match
access-group 100<BR>class-map match-any day2day<BR> match access-group
101</FONT></DIV>
<DIV> </DIV>
<DIV><FONT face=Arial>policy-map DRandVoice<BR> class voice<BR>
priority percent 3<BR> class DR<BR> bandwidth remaining percent
89<BR> class day2day<BR> bandwidth remaining percent
8</FONT></DIV>
<DIV> </DIV>
<DIV><FONT face=Arial>access-list 100 permit ip 10.31.0.0
0.0.255.255<BR>access-list 101 deny ip 10.31.0.0 0.0.255.255<BR>access-list
101 permit ip any any<BR></FONT></DIV>
<DIV> </DIV>
<DIV> </DIV>
<DIV> </DIV>
<DIV align=left><FONT face="Monotype Corsiva" color=#145040
size=6><STRONG>Kevin Dunn</STRONG></FONT></DIV>
<DIV align=left><STRONG><FONT face="Monotype Corsiva" color=#145040
size=6>Marathon Cheese Corporation</FONT></STRONG></DIV>
<DIV> </DIV></DIV></DIV><BR></DIV></DIV></DIV><PRE></PRE>
<P>Confidentiality: The information in this electronic mail may contain
confidential, sensitive and/or protected health information intended only
for the addressee(s). Any other person, including anyone who believes he/she
might have received it due to an addressing error, is requested to notify
this sender immediately by return e-mail, and shall delete it without
further reading and retention. The information shall not be forwarded or
shared unless in compliance with MMIC policies on confidentiality, and/or
the written permission of this sender.
</P></BLOCKQUOTE></DIV><BR></DIV></DIV></DIV>
<DIV>
<DIV></DIV>
<DIV class=h5><PRE></PRE>
<P>Confidentiality: The information in this electronic mail may contain
confidential, sensitive and/or protected health information intended only for
the addressee(s). Any other person, including anyone who believes he/she might
have received it due to an addressing error, is requested to notify this
sender immediately by return e-mail, and shall delete it without further
reading and retention. The information shall not be forwarded or shared unless
in compliance with MMIC policies on confidentiality, and/or the written
permission of this sender. </P></DIV></DIV></BLOCKQUOTE></DIV><BR></BODY></HTML>
<pre></PRE><P>Confidentiality: The information in this electronic mail may contain confidential, sensitive and/or protected health information intended only for the addressee(s). Any other person, including anyone who believes he/she might have received it due to an addressing error, is requested to notify this sender immediately by return e-mail, and shall delete it without further reading and retention. The information shall not be forwarded or shared unless in compliance with MMIC policies on confidentiality, and/or the written permission of this sender.
</P>