Hi all,<br>��� I am trying to configure a� 6 port T1 module in a CMM, and am thoroughly stumped.� I have a T1 drop that was tested good and comes up when connected to a 3800 with a T1 VWIC card.�� The T1 will not come up to any of the ports on the 6T1 module on the CMM.� The Controller configs are identical on the router and the CMM.� I get a green LED on the CMM card but thats it.� The weird part is that the router T1 will come up to the carrier T1, a T1 loopback, and even the T1 connected to the CMM module with a crossover T1 cable.�� The CMM module will not come up to a loopback, nor the Router t1, nor the carrier t1(but the LED will green up).� I could not find any documentation on a different Pinout for CMM module, so my guess is I am missing something in the config.� Is there anything special needed for these CMM modules, or anybody have a suggestion on a command to troubleshoot the Layer 1 issue?<br>
<br><b>Config for CMM:</b><br>#show controllers t1 1/0 brief<br>T1 1/0 is down.<br>� Applique type is Channelized T1<br>� Cablelength is long gain36 0db<br>� Receiver has loss of signal.<br>� alarm-trigger is not set<br>� Soaking time: 3, Clearance time: 10<br>
� AIS State:Clear� LOS State:Clear� LOF State:Clear<br>� Framing is ESF, Line Code is B8ZS, Clock Source is Line.<br><br>#show int se1/0:23<br>Serial1/0:23 is reset, line protocol is down<br>� Hardware is DSX1<br>� MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,<br>
���� reliability 255/255, txload 1/255, rxload 1/255<br>� Encapsulation HDLC, loopback not set<br><br>#show isdn status<br>Global ISDN Switchtype = primary-ni<br>ISDN Serial1/0:23 interface<br>������� dsl 0, interface ISDN Switchtype = primary-ni<br>
��� Layer 1 Status:<br>������� DEACTIVATED<br>��� Layer 2 Status:<br>������� TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED<br>��� Layer 3 Status:<br>������� 0 Active Layer 3 Call(s)<br>��� Active dsl 0 CCBs = 0<br>��� The Free Channel Mask:� 0x00000000<br>
��� Number of L2 Discards = 0, L2 Session ID = 0<br><br><b><br>Config for the T1 VWIC:</b><br>#show controllers t1 0/1/0 brief<br>T1 0/1/0 is up.<br>� Applique type is Channelized T1<br>� Cablelength is long gain36 0db<br>
� No alarms detected.<br>� alarm-trigger is not set<br>� Soaking time: 3, Clearance time: 10<br>� AIS State:Clear� LOS State:Clear� LOF State:Clear<br>� Version info Firmware: 20040802, FPGA: 13, spm_count = 0<br>� Framing is ESF, Line Code is B8ZS, Clock Source is Line.<br>
<br>Serial0/1/0:23 is up, line protocol is up (spoofing)<br>
� Hardware is DSX1<br>
� MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,<br>
���� reliability 255/255, txload 1/255, rxload 1/255<br>
� Encapsulation HDLC, loopback not set<br><br>ISDN Serial0/1/0:23 interface<br>������� dsl 0, interface ISDN Switchtype = primary-ni<br>������� L2 Protocol = Q.921 0x0000� L3 Protocol(s) = CCM MANAGER 0x0003<br>��� Layer 1 Status:<br>
������� ACTIVE<br>��� Layer 2 Status:<br>������� TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED<br>��� Layer 3 Status:<br>������� 0 Active Layer 3 Call(s)<br>��� Active dsl 0 CCBs = 0<br>��� The Free Channel Mask:� 0x807FFFFF<br>
��� Number of L2 Discards = 0, L2 Session ID = 23<br><br><br><br><br><br><br><br>