config is for MGCP. Not having much experience with the CMM, i stared and compared from a production CMM module with the same config. I know the running config doesnt necessarily show all the settings, but that and the guide were my only reference. switch type was primary-ni, production and lab devices both have T1's from teh same carrier, so I duplicated that in the lab device as well. One of the things Im not sure about is the difference between the global config switch-type and the interface config of switch type. Now that I think about it, i did not check the global setting, only the interface setting...<br>
<br><div class="gmail_quote">On Mon, Mar 8, 2010 at 5:01 PM, Scott Voll <span dir="ltr"><<a href="mailto:svoll.voip@gmail.com">svoll.voip@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex;">
MGCP or H323?<div><br></div><div><div>!</div><div>controller T1 0/0/0</div><div> clock source line primary</div><div> pri-group timeslots 1-24 <-- I'm guessing maybe the timeslots?</div><div><br></div><div>Switch type?</div>
<div><br></div><div><br></div><div><br></div><div>Scott</div><div><br></div><div><br></div><br><div class="gmail_quote">On Mon, Mar 8, 2010 at 2:53 PM, Frank Arrasmith <span dir="ltr"><<a href="mailto:frank.arrasmith@gmail.com" target="_blank">frank.arrasmith@gmail.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Hi all,<br> I am trying to configure a 6 port T1 module in a CMM, and am thoroughly stumped. I have a T1 drop that was tested good and comes up when connected to a 3800 with a T1 VWIC card. The T1 will not come up to any of the ports on the 6T1 module on the CMM. The Controller configs are identical on the router and the CMM. I get a green LED on the CMM card but thats it. The weird part is that the router T1 will come up to the carrier T1, a T1 loopback, and even the T1 connected to the CMM module with a crossover T1 cable. The CMM module will not come up to a loopback, nor the Router t1, nor the carrier t1(but the LED will green up). I could not find any documentation on a different Pinout for CMM module, so my guess is I am missing something in the config. Is there anything special needed for these CMM modules, or anybody have a suggestion on a command to troubleshoot the Layer 1 issue?<br>
<br><b>Config for CMM:</b><br>#show controllers t1 1/0 brief<br>T1 1/0 is down.<br> Applique type is Channelized T1<br> Cablelength is long gain36 0db<br> Receiver has loss of signal.<br> alarm-trigger is not set<br>
Soaking time: 3, Clearance time: 10<br>
AIS State:Clear LOS State:Clear LOF State:Clear<br> Framing is ESF, Line Code is B8ZS, Clock Source is Line.<br><br>#show int se1/0:23<br>Serial1/0:23 is reset, line protocol is down<br> Hardware is DSX1<br> MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,<br>
reliability 255/255, txload 1/255, rxload 1/255<br> Encapsulation HDLC, loopback not set<br><br>#show isdn status<br>Global ISDN Switchtype = primary-ni<br>ISDN Serial1/0:23 interface<br> dsl 0, interface ISDN Switchtype = primary-ni<br>
Layer 1 Status:<br> DEACTIVATED<br> Layer 2 Status:<br> TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED<br> Layer 3 Status:<br> 0 Active Layer 3 Call(s)<br> Active dsl 0 CCBs = 0<br> The Free Channel Mask: 0x00000000<br>
Number of L2 Discards = 0, L2 Session ID = 0<br><br><b><br>Config for the T1 VWIC:</b><br>#show controllers t1 0/1/0 brief<br>T1 0/1/0 is up.<br> Applique type is Channelized T1<br> Cablelength is long gain36 0db<br>
No alarms detected.<br> alarm-trigger is not set<br> Soaking time: 3, Clearance time: 10<br> AIS State:Clear LOS State:Clear LOF State:Clear<br> Version info Firmware: 20040802, FPGA: 13, spm_count = 0<br> Framing is ESF, Line Code is B8ZS, Clock Source is Line.<br>
<br>Serial0/1/0:23 is up, line protocol is up (spoofing)<br>
Hardware is DSX1<br>
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,<br>
reliability 255/255, txload 1/255, rxload 1/255<br>
Encapsulation HDLC, loopback not set<br><br>ISDN Serial0/1/0:23 interface<br> dsl 0, interface ISDN Switchtype = primary-ni<br> L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003<br> Layer 1 Status:<br>
ACTIVE<br> Layer 2 Status:<br> TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED<br> Layer 3 Status:<br> 0 Active Layer 3 Call(s)<br> Active dsl 0 CCBs = 0<br> The Free Channel Mask: 0x807FFFFF<br>
Number of L2 Discards = 0, L2 Session ID = 23<br><br><br><br><br><br><br><br>
<br>_______________________________________________<br>
cisco-voip mailing list<br>
<a href="mailto:cisco-voip@puck.nether.net" target="_blank">cisco-voip@puck.nether.net</a><br>
<a href="https://puck.nether.net/mailman/listinfo/cisco-voip" target="_blank">https://puck.nether.net/mailman/listinfo/cisco-voip</a><br>
<br></blockquote></div><br></div>
</blockquote></div><br>