<html>
<head>
<style><!--
.hmmessage P
{
margin:0px;
padding:0px
}
body.hmmessage
{
font-size: 10pt;
font-family:Verdana
}
--></style>
</head>
<body class='hmmessage'>
A couple of things to look out for :<BR>
<BR>
- Storms can cause problems on FXO hardware. I don't know about Cisco stuff, but I have hade PABX with FXO ports which, when there have been storms nearby with lightening, you somethines get lightening strikes on the external network which send a spike up the line and pops your FXO hardware. It's worth swapping one of your FXO cards to see if this helps.<BR>
<BR>
- Again, I don't know about Cisco FOX ports, but some PABX I have worked with do not like the pair of wires on analogue lines being reversed. the A-leg should be -40 odd volts and the B-leg should be around zero (in the UK). A lot of PABX don't care about reversals, but some do. As for Cisco I dont know, but if it does care, and there is a reversal, then this could be the problem. Reversals are very common when there have been problems on the public network (caused by storms etc) as the PTO guys will disconnect lines for testing and then reconnect them but they don't pay too much attention to polarity; they just see it as a pair of wires and just reconnect the pair any old way. (They wont admit to it, but yes, they do this!)<BR>
<BR>
- If the lines have been swapped to ground start instead of loop start then the wiring will also need to be correct. There needs to be a (good) ground wire connected, because to get dial tone, you (or rather the equipment) has to earth one of the legs on the analogue line (I cant remember which one but I think its the A-leg). It's always better to ensure lines are loop start as then you dont have to mess around with a good ground line. i.e. you might have a ground line connected but it aint good enough to ground start the line. NOTE: Mains Earth (ie, that supplied through the plug of the equipment) is not always good enough, because the analogue lines take their reference voltage from the local exchange. If there is a voltage difference between your earth and the local exchange's earth then this will cause problems. I can't tell you the hours I've spent with ground loop impedance testers, trying to get a good earth connection. It is a PAIN!<BR>
<BR>
So, I hope some of this helps.<BR>
<BR>
Simon<BR>
Cambridge<BR>
UK<BR>
<BR>
<BR> <BR>
<HR id=stopSpelling>
From: Hyoun.Kim@chartercom.com<BR>To: erickbee@gmail.com<BR>Date: Mon, 14 Jun 2010 13:45:03 -0500<BR>CC: cisco-voip@puck.nether.net<BR>Subject: Re: [cisco-voip] FXO Outbound Call Not Working<BR><BR>
<STYLE>
.ExternalClass .ecxshape
{;}
</STYLE>
<STYLE>
.ExternalClass p.ecxMsoNormal, .ExternalClass li.ecxMsoNormal, .ExternalClass div.ecxMsoNormal
{margin-bottom:.0001pt;font-size:12.0pt;font-family:'Times New Roman','serif';}
.ExternalClass a:link, .ExternalClass span.ecxMsoHyperlink
{color:blue;text-decoration:underline;}
.ExternalClass a:visited, .ExternalClass span.ecxMsoHyperlinkFollowed
{color:purple;text-decoration:underline;}
.ExternalClass p
{margin-right:0in;margin-left:0in;font-size:12.0pt;font-family:'Times New Roman','serif';}
.ExternalClass pre
{margin-bottom:.0001pt;font-size:10.0pt;font-family:'Courier New';}
.ExternalClass span.ecxHTMLPreformattedChar
{font-family:Consolas;}
.ExternalClass span.ecxEmailStyle20
{font-family:'Calibri','sans-serif';color:#1F497D;}
.ExternalClass .ecxMsoChpDefault
{;}
@page Section1
{size:8.5in 11.0in;}
.ExternalClass div.ecxSection1
{page:Section1;}
</STYLE>
<DIV class=ecxSection1>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d; FONT-FAMILY: 'Calibri','sans-serif'">Thanks all. I appreciate the input. When I asked the Local IT Admin about more details, he said prior to the weekend (ever since I installed the system), everything was fine. But then they got terrible storms over the weekend in Alabama and that’s when phones weren’t responsive. He rebooted the router and then that’s when we got the symptoms I mentioned earlier (inbound calls ok, outbound no good).</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d; FONT-FAMILY: 'Calibri','sans-serif'"> </SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d; FONT-FAMILY: 'Calibri','sans-serif'">I’m having him track down a buttset to use for final testing before calling AT&T.</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d; FONT-FAMILY: 'Calibri','sans-serif'"> </SPAN></P>
<P class=ecxMsoNormal><B><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d; FONT-FAMILY: 'Verdana','sans-serif'">Hyoun Kim</SPAN></B></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d; FONT-FAMILY: 'Verdana','sans-serif'">Network Administrator</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d; FONT-FAMILY: 'Verdana','sans-serif'">Charter Media - East Division</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d; FONT-FAMILY: 'Verdana','sans-serif'">640 Broadmor Blvd, Suite 80</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d; FONT-FAMILY: 'Verdana','sans-serif'">Murfreesboro, TN 37129</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d; FONT-FAMILY: 'Verdana','sans-serif'"> </SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d; FONT-FAMILY: 'Verdana','sans-serif'">Email: <A href="mailto:Hyoun.Kim@chartercom.com">Hyoun.Kim@chartercom.com</A></SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d; FONT-FAMILY: 'Verdana','sans-serif'">Office: 615.217.6245</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d; FONT-FAMILY: 'Verdana','sans-serif'">Fax: 615.217.6247</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d; FONT-FAMILY: 'Calibri','sans-serif'"> </SPAN></P>
<DIV style="BORDER-RIGHT: medium none; PADDING-RIGHT: 0in; BORDER-TOP: #b5c4df 1pt solid; PADDING-LEFT: 0in; PADDING-BOTTOM: 0in; BORDER-LEFT: medium none; PADDING-TOP: 3pt; BORDER-BOTTOM: medium none">
<P class=ecxMsoNormal><B><SPAN style="FONT-SIZE: 10pt; FONT-FAMILY: 'Tahoma','sans-serif'">From:</SPAN></B><SPAN style="FONT-SIZE: 10pt; FONT-FAMILY: 'Tahoma','sans-serif'"> Erick B. [mailto:erickbee@gmail.com] <BR><B>Sent:</B> Monday, June 14, 2010 1:06 PM<BR><B>To:</B> Kim, Hyoun S<BR><B>Cc:</B> Dennis Heim; ccieid1ot; cisco-voip@puck.nether.net<BR><B>Subject:</B> Re: [cisco-voip] FXO Outbound Call Not Working</SPAN></P></DIV>
<P class=ecxMsoNormal> </P>
<P class=ecxMsoNormal>The next step would be like I said, try out each line disconnected from router FXO port with a old POTS / princess phone and see if the phone lines work, or use a Butt Sett on them like Dennis suggested. </P>
<DIV>
<P class=ecxMsoNormal> </P></DIV>
<DIV>
<P class=ecxMsoNormal>The 0x00 is indication of router voice-port seeing no voltage on the line plugged into that port (maybe there is nothing plugged into the port, or it got disconnected somewhere upstream). This command however gives you more of a warm fuzzy then anything. With analog lines, there is no real good way from router command line to really tell what is going on with the actual phone lines. The no circuit on the call history means the router attempted to make a call but didn't detect a phone line / dial tone on that port to do so. </P></DIV>
<DIV>
<P class=ecxMsoNormal> </P></DIV>
<DIV>
<P class=ecxMsoNormal>But, most likely a telephone provider / phone line cabling issue since this used to work fine with no changes on your gateway. </P></DIV>
<DIV>
<P class=ecxMsoNormal style="MARGIN-BOTTOM: 12pt"> </P>
<DIV>
<P class=ecxMsoNormal>On Mon, Jun 14, 2010 at 10:07 AM, Kim, Hyoun S <<A href="mailto:Hyoun.Kim@chartercom.com">Hyoun.Kim@chartercom.com</A>> wrote:</P>
<DIV>
<DIV>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">I’m having a local IT guy from down there to try it. I can’t because I’m over 300 miles away.</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">In the event that phone calls cannot be made outbound, what needs to be done given the e-mail I wrote out below?</SPAN></P>
<DIV>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<DIV>
<P class=ecxMsoNormal><B><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Hyoun Kim</SPAN></B></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Network Administrator</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Charter Media - East Division</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">640 Broadmor Blvd, Suite 80</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Murfreesboro, TN 37129</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d"> </SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Email: <A href="mailto:Hyoun.Kim@chartercom.com">Hyoun.Kim@chartercom.com</A></SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Office: 615.217.6245</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Fax: 615.217.6247</SPAN></P></DIV>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P></DIV>
<DIV>
<DIV style="BORDER-RIGHT: medium none; PADDING-RIGHT: 0in; BORDER-TOP: #b5c4df 1pt solid; PADDING-LEFT: 0in; PADDING-BOTTOM: 0in; BORDER-LEFT: medium none; PADDING-TOP: 3pt; BORDER-BOTTOM: medium none">
<P class=ecxMsoNormal><B><SPAN style="FONT-SIZE: 10pt">From:</SPAN></B><SPAN style="FONT-SIZE: 10pt"> Dennis Heim [mailto:<A href="mailto:Dennis.Heim@cdw.com">Dennis.Heim@cdw.com</A>] <BR><B>Sent:</B> Monday, June 14, 2010 9:07 AM<BR><B>To:</B> Kim, Hyoun S; Erick B.; ccieid1ot</SPAN></P>
<DIV>
<P class=ecxMsoNormal><BR><B>Cc:</B> <A href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</A></P></DIV>
<P class=ecxMsoNormal><B>Subject:</B> RE: [cisco-voip] FXO Outbound Call Not Working</P></DIV></DIV>
<DIV>
<DIV>
<P class=ecxMsoNormal> </P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">If you connect your butt-set to these lines do they work?</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<DIV>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 10pt; COLOR: #1f497d">Dennis Heim<BR>Network Voice Engineer<BR>CDW Advanced Technology Services<BR>11711 N. Meridian Street, Suite 225<BR>Carmel, IN 46032<BR><BR>317.569.4255 Office<BR></SPAN><SPAN style="FONT-SIZE: 10pt; COLOR: black">317.569.4201 Fax<BR></SPAN><SPAN style="FONT-SIZE: 10pt; COLOR: #1f497d">317.694.6070 Cell</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"><A title=mailto:dennis.heim@berbee.com href="mailto:dennis.heim@cdw.com">dennis.heim@cdw.com</A><BR></SPAN><SPAN style="COLOR: #1f497d"><A href="http://www.cdw.com/content/solutions/unified-communications/">cdw.com/content/solutions/unified-communications/</A></SPAN></P>
<P class=ecxMsoNormal><SPAN style="COLOR: #1f497d"> </SPAN></P></DIV>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<DIV>
<DIV style="BORDER-RIGHT: medium none; PADDING-RIGHT: 0in; BORDER-TOP: #b5c4df 1pt solid; PADDING-LEFT: 0in; PADDING-BOTTOM: 0in; BORDER-LEFT: medium none; PADDING-TOP: 3pt; BORDER-BOTTOM: medium none">
<P class=ecxMsoNormal><B><SPAN style="FONT-SIZE: 10pt">From:</SPAN></B><SPAN style="FONT-SIZE: 10pt"> <A href="mailto:cisco-voip-bounces@puck.nether.net">cisco-voip-bounces@puck.nether.net</A> [mailto:<A href="mailto:cisco-voip-bounces@puck.nether.net">cisco-voip-bounces@puck.nether.net</A>] <B>On Behalf Of </B>Kim, Hyoun S<BR><B>Sent:</B> Monday, June 14, 2010 9:53 AM<BR><B>To:</B> Erick B.; ccieid1ot<BR><B>Cc:</B> <A href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</A><BR><B>Subject:</B> Re: [cisco-voip] FXO Outbound Call Not Working</SPAN></P></DIV></DIV>
<P class=ecxMsoNormal> </P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">Oh sorry Erick.</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">The hardware is a C2811 with 3 VIC2-4FXO cards utilizing 12 analog phone lines from the telco (AT&T). I have 2 DSP modules (PVDM2-16 & 64) installed with a NM-CUE module installed as well.</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">All of the lines exhibit the same problem where people can dial to the office and the phone rings. But outbound calls by that office do not work and display that same error I showed in the first e-mail. I attempted to use the groundstart command on my voice ports per CCIEID1OT’s recommendation, but that didn’t work either.</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">Thanks for that call command. Here is the output for outbound calls… I see the “no circuit 34” you mentioned!</SPAN></P>
<P class=ecxMsoNormal style="MARGIN-LEFT: 0.5in"><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">15B7 : 347 246488340ms.346 +-1 +1260 pid:6 Originate 16152176245</SPAN></P>
<P class=ecxMsoNormal style="MARGIN-LEFT: 0.5in"><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> dur 00:00:00 tx:0/0 rx:0/0 22 (no circuit (34))</SPAN></P>
<P class=ecxMsoNormal style="MARGIN-LEFT: 0.5in"><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> Telephony 0/0/0 (347) [0/0/0] tx:0/0/0ms None noise:0dBm acom:0dBm</SPAN></P>
<P class=ecxMsoNormal style="MARGIN-LEFT: 0.5in"><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> long duration call detected:n long dur callduration :n/a timestamp:n/a</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">Also, here are the results from the test voice command you gave me:</SPAN></P>
<P class=ecxMsoNormal style="MARGIN-LEFT: 0.5in"><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">005578: Jun 14 08:50:42.880 CDT:</SPAN></P>
<P class=ecxMsoNormal style="MARGIN-LEFT: 0.5in"><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">Values read from SiLabs Codec connected to DSP 0, channel 8:</SPAN></P>
<P class=ecxMsoNormal style="MARGIN-LEFT: 0.5in"><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">--------------------------------------------------------------</SPAN></P>
<P class=ecxMsoNormal style="MARGIN-LEFT: 0.5in"><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">Register 29 = 0xD5</SPAN></P>
<P class=ecxMsoNormal style="MARGIN-LEFT: 0.5in"><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">I noticed the Register 29 comes out with different values for different ports. Such as 0x00, 0xD5 & 0xD4.</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">What are your recommendations since I get the “no circuit 34”? The only thread I saw in regards to my initial error on Cisco’s support forums is this: <A href="https://supportforums.cisco.com/message/3118805#3118805">https://supportforums.cisco.com/message/3118805#3118805</A></SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">However, the user ended up saying that the Telco was at fault and that’s how he got it fixed. I just wanted to make sure all my hardware was ok before tell AT&T because in the past, they always tell me to check my equipment first.</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d">Thanks so much.</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<P class=ecxMsoNormal><B><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Hyoun Kim</SPAN></B></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Network Administrator</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Charter Media - East Division</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">640 Broadmor Blvd, Suite 80</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Murfreesboro, TN 37129</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d"> </SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Email: <A href="mailto:Hyoun.Kim@chartercom.com">Hyoun.Kim@chartercom.com</A></SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Office: 615.217.6245</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 8pt; COLOR: #1f497d">Fax: 615.217.6247</SPAN></P>
<P class=ecxMsoNormal><SPAN style="FONT-SIZE: 11pt; COLOR: #1f497d"> </SPAN></P>
<DIV style="BORDER-RIGHT: medium none; PADDING-RIGHT: 0in; BORDER-TOP: #b5c4df 1pt solid; PADDING-LEFT: 0in; PADDING-BOTTOM: 0in; BORDER-LEFT: medium none; PADDING-TOP: 3pt; BORDER-BOTTOM: medium none">
<P class=ecxMsoNormal><B><SPAN style="FONT-SIZE: 10pt">From:</SPAN></B><SPAN style="FONT-SIZE: 10pt"> Erick B. [mailto:<A href="mailto:erickbee@gmail.com">erickbee@gmail.com</A>] <BR><B>Sent:</B> Friday, June 11, 2010 11:51 PM<BR><B>To:</B> ccieid1ot<BR><B>Cc:</B> Kim, Hyoun S; <A href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</A><BR><B>Subject:</B> Re: [cisco-voip] FXO Outbound Call Not Working</SPAN></P></DIV>
<P class=ecxMsoNormal> </P>
<P class=ecxMsoNormal>I would start by making sure each of the analog lines worked fine, with a regular old princess phone, if possible. Since it was working fine, and config hasn't changed, it's likely an issue with the phone lines or cabling.</P>
<DIV>
<P class=ecxMsoNormal> </P></DIV>
<DIV>
<P class=ecxMsoNormal>You don't mention what type of hardware you have, but try reseating the cables, especially if you have a amphenol connector. Those tend to vibrate loose over time and cause problems like this, where calls fail but some work depending on what port is being used. </P>
<DIV>
<P class=ecxMsoNormal> </P>
<DIV>
<P class=ecxMsoNormal>Output from 'show call history voice brief' may be useful. If the cause/reason states no circuit 34 then the line may be a problem. </P></DIV>
<DIV>
<P class=ecxMsoNormal> </P></DIV>
<DIV>
<P class=ecxMsoNormal>If you have a ISR router, you can try this, but it varies with voice-card hardware, a 0x0 result indicates the router see's no voltage on whatever is attached to the voice-port. </P></DIV>
<DIV>
<P class=ecxMsoNormal> </P></DIV>
<DIV>
<P class=ecxMsoNormal>term mon</P></DIV>
<DIV>
<P class=ecxMsoNormal>test voice port x/y/z si-reg-read 29 1</P></DIV>
<DIV>
<P class=ecxMsoNormal> </P></DIV>
<DIV>
<P class=ecxMsoNormal>Where x/y/z is your voice-port #/#/#, you need term mon to see the output from the test command. </P></DIV>
<DIV>
<P class=ecxMsoNormal> </P>
<DIV>
<P class=ecxMsoNormal> </P>
<DIV>
<P class=ecxMsoNormal>On Fri, Jun 11, 2010 at 3:27 PM, ccieid1ot <<A href="mailto:ccieid1ot@gmail.com">ccieid1ot@gmail.com</A>> wrote:</P>
<P class=ecxMsoNormal style="MARGIN-BOTTOM: 12pt">Try changing to ground-start.</P>
<DIV>
<DIV>
<DIV>
<P class=ecxMsoNormal>On Fri, Jun 11, 2010 at 2:43 PM, Kim, Hyoun S <<A href="mailto:Hyoun.Kim@chartercom.com">Hyoun.Kim@chartercom.com</A>> wrote:</P></DIV></DIV>
<BLOCKQUOTE style="BORDER-RIGHT: medium none; PADDING-RIGHT: 0in; BORDER-TOP: medium none; PADDING-LEFT: 6pt; MARGIN-BOTTOM: 5pt; PADDING-BOTTOM: 0in; MARGIN-LEFT: 4.8pt; BORDER-LEFT: #cccccc 1pt solid; MARGIN-RIGHT: 0in; PADDING-TOP: 0in; BORDER-BOTTOM: medium none">
<DIV>
<DIV>
<DIV>
<DIV>
<P class=ecxMsoNormal>I have a router that I’ve utilizes FXO modules for making calls. When I first set it up, everything worked fine. A few months later, users started reporting to me an intermittent problem for outbound calls. Sometimes they can make calls, but the majority of the time, they get a fast busy signal. I compared the current router’s configuration to when I originally saved the configuration from initial setup. Nothing changed. Out of perhaps 10 calls made, maybe 1 of them went through.</P>
<P class=ecxMsoNormal> </P>
<P class=ecxMsoNormal>The following is the config for a voice-port. All the other ones have the same config. 2857 is the number to the Unity Express.</P>
<P class=ecxMsoNormal>voice-port 0/0/0</P>
<P class=ecxMsoNormal> trunk-group POTS-FXO</P>
<P class=ecxMsoNormal> connection plar opx 2857</P>
<P class=ecxMsoNormal>caller-id enable</P>
<P class=ecxMsoNormal> </P>
<P class=ecxMsoNormal>I did try “no supervisory disconnect signal” but that didn’t work either.</P>
<P class=ecxMsoNormal> </P>
<P class=ecxMsoNormal>I turned on debugging for “vpm signal” and made several calls to different phone numbers. The following output is just an example of what the result is for all calls:</P>
<P class=ecxMsoNormal>001401: Jun 11 14:36:33.104 CDT: htsp_digit_ready(50/0/10.1): digit = 1</P>
<P class=ecxMsoNormal>001402: Jun 11 14:36:33.500 CDT: htsp_digit_ready(50/0/10.1): digit = 6</P>
<P class=ecxMsoNormal>001403: Jun 11 14:36:33.832 CDT: htsp_digit_ready(50/0/10.1): digit = 1</P>
<P class=ecxMsoNormal>001404: Jun 11 14:36:34.124 CDT: htsp_digit_ready(50/0/10.1): digit = 5</P>
<P class=ecxMsoNormal>001405: Jun 11 14:36:34.548 CDT: htsp_digit_ready(50/0/10.1): digit = 2</P>
<P class=ecxMsoNormal>001406: Jun 11 14:36:34.816 CDT: htsp_digit_ready(50/0/10.1): digit = 1</P>
<P class=ecxMsoNormal>001407: Jun 11 14:36:35.204 CDT: htsp_digit_ready(50/0/10.1): digit = 7</P>
<P class=ecxMsoNormal>001408: Jun 11 14:36:35.636 CDT: htsp_digit_ready(50/0/10.1): digit = 6</P>
<P class=ecxMsoNormal>001409: Jun 11 14:36:35.904 CDT: htsp_digit_ready(50/0/10.1): digit = 3</P>
<P class=ecxMsoNormal>001410: Jun 11 14:36:36.308 CDT: htsp_digit_ready(50/0/10.1): digit = 0</P>
<P class=ecxMsoNormal>001411: Jun 11 14:36:36.576 CDT: htsp_digit_ready(50/0/10.1): digit = 0</P>
<P class=ecxMsoNormal>001412: Jun 11 14:36:36.588 CDT: htsp_timer_stop3</P>
<P class=ecxMsoNormal>001413: Jun 11 14:36:36.588 CDT: htsp_process_event: [50/0/10.1, EFXS_OFFHOOK, E_HTSP_PROCEEDING]efxs_offhook_proceeding</P>
<P class=ecxMsoNormal>001414: Jun 11 14:36:36.588 CDT: [50/0/10.1] set signal state = 0x8 timestamp = 0htsp_setup_req</P>
<P class=ecxMsoNormal>001415: Jun 11 14:36:36.592 CDT: htsp_process_event: [0/0/0, FXOLS_ONHOOK, E_HTSP_SETUP_REQ]fxols_onhook_setup</P>
<P class=ecxMsoNormal>001416: Jun 11 14:36:36.592 CDT: [0/0/0] set signal state = 0xC timestamp = 0</P>
<P class=ecxMsoNormal>001417: Jun 11 14:36:36.592 CDT: htsp_timer - 1300 msec</P>
<P class=ecxMsoNormal>001418: Jun 11 14:36:36.844 CDT: htsp_process_event: [0/0/0, FXOLS_WAIT_DIAL_TONE, E_DSP_SIG_1100]fxols_power_denial_detected</P>
<P class=ecxMsoNormal>001419: Jun 11 14:36:36.844 CDT: htsp_timer2 - 1000 msec</P>
<P class=ecxMsoNormal>001420: Jun 11 14:36:36.844 CDT: htsp_timer_stop</P>
<P class=ecxMsoNormal>001421: Jun 11 14:36:37.844 CDT: htsp_process_event: [0/0/0, FXOLS_WAIT_DIAL_TONE, E_HTSP_EVENT_TIMER2]fxols_power_den_disc</P>
<P class=ecxMsoNormal>001422: Jun 11 14:36:37.844 CDT: htsp_timer_stop</P>
<P class=ecxMsoNormal>001423: Jun 11 14:36:37.844 CDT: htsp_timer_stop2</P>
<P class=ecxMsoNormal>001424: Jun 11 14:36:37.844 CDT: [0/0/0] set signal state = 0x4 timestamp = 0</P>
<P class=ecxMsoNormal>001425: Jun 11 14:36:37.848 CDT: htsp_process_event: [0/0/0, FXOLS_ONHOOK, E_HTSP_RELEASE_REQ]fxols_onhook_release</P>
<P class=ecxMsoNormal>001426: Jun 11 14:36:54.497 CDT: htsp_process_event: [50/0/10.1, EFXS_OFFHOOK, E_DSP_SIG_0100]efxs_offhook_onhook</P>
<P class=ecxMsoNormal>001427: Jun 11 14:36:54.497 CDT: htsp_timer - 10 msec</P>
<P class=ecxMsoNormal>001428: Jun 11 14:36:54.509 CDT: htsp_process_event: [50/0/10.1, EFXS_OFFHOOK, E_HTSP_EVENT_TIMER]efxs_offhook_timer</P>
<P class=ecxMsoNormal>001429: Jun 11 14:36:54.513 CDT: htsp_process_event: [50/0/10.1, EFXS_ONHOOK, E_HTSP_RELEASE_REQ]efxs_onhook_release</P>
<P class=ecxMsoNormal>001430: Jun 11 14:36:54.513 CDT: htsp_timer_stop</P>
<P class=ecxMsoNormal>001431: Jun 11 14:36:54.513 CDT: [50/0/10.1] set signal state = 0x4 timestamp = 0</P>
<P class=ecxMsoNormal> </P>
<P class=ecxMsoNormal>Thanks for any help.</P>
<P class=ecxMsoNormal style="TEXT-ALIGN: right" align=right><SPAN style="COLOR: #717074"><IMG id=ecx_x0000_i1025 height=32 alt=2C_CharLogo_Tag_CMYK src="cid:image001.jpg@01CB0BC7.CABCCF40" width=132 border=0></SPAN></P>
<DIV class=ecxMsoNormal style="TEXT-ALIGN: center" align=center><SPAN style="COLOR: #717074">
<HR style="COLOR: #7fa2b8" align=center width="100%" noShade SIZE=4>
</SPAN></DIV>
<P class=ecxMsoNormal><B><SPAN style="FONT-SIZE: 10pt; COLOR: #717074">Hyoun Kim</SPAN></B><B><SPAN style="FONT-SIZE: 10pt; COLOR: #7fa2b8"> •</SPAN><SPAN style="COLOR: #717074"> </SPAN></B><SPAN style="FONT-SIZE: 8pt; COLOR: #717074">Network Administrator – East Division</SPAN></P>
<P class=ecxMsoNormal style="TEXT-ALIGN: right" align=right><SPAN style="FONT-SIZE: 8pt; COLOR: #717074">640 Broadmor Blvd</SPAN><SPAN style="FONT-SIZE: 10pt; COLOR: #717074"> </SPAN><B><SPAN style="COLOR: #7fa2b8">• </SPAN></B><SPAN style="FONT-SIZE: 8pt; COLOR: #717074">Suite 80</SPAN><SPAN style="FONT-SIZE: 10pt; COLOR: #717074"> </SPAN><B><SPAN style="COLOR: #7fa2b8">• </SPAN></B><SPAN style="FONT-SIZE: 8pt; COLOR: #717074">Murfreesboro, TN 37129</SPAN></P>
<P class=ecxMsoNormal style="TEXT-ALIGN: right" align=right><SPAN style="FONT-SIZE: 10pt; COLOR: #717074; FONT-FAMILY: 'Wingdings 2'">'</SPAN><SPAN style="FONT-SIZE: 8pt; COLOR: #717074"> 615.217.6245</SPAN><SPAN style="FONT-SIZE: 10pt; COLOR: #717074"> </SPAN><B><SPAN style="COLOR: #7fa2b8">• </SPAN></B><SPAN style="FONT-SIZE: 10pt; COLOR: #717074; FONT-FAMILY: 'Wingdings 2'">7</SPAN><SPAN style="COLOR: #717074"> </SPAN><SPAN style="FONT-SIZE: 8pt; COLOR: #717074">615.217.6247</SPAN><SPAN style="FONT-SIZE: 10pt; COLOR: #717074"> </SPAN><B><SPAN style="COLOR: #7fa2b8">• </SPAN></B><SPAN style="FONT-SIZE: 10pt; COLOR: #717074; FONT-FAMILY: Wingdings">*</SPAN><SPAN style="FONT-SIZE: 10pt; COLOR: #717074"> </SPAN><SPAN style="FONT-SIZE: 8pt; COLOR: #717074"><A href="mailto:Hyoun.Kim@chartercom.com">Hyoun.Kim@chartercom.com</A></SPAN></P>
<P class=ecxMsoNormal> </P></DIV><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt">E-MAIL CONFIDENTIALITY NOTICE: </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt">The contents of this e-mail message and </PRE><PRE style="MARGIN-BOTTOM: 12pt">any attachments are intended solely for the </PRE><PRE style="MARGIN-BOTTOM: 12pt">addressee(s) and may contain confidential </PRE><PRE style="MARGIN-BOTTOM: 12pt">and/or legally privileged information. If you </PRE><PRE style="MARGIN-BOTTOM: 12pt">are not the intended recipient of this message </PRE><PRE style="MARGIN-BOTTOM: 12pt">or if this message has been addressed to you </PRE><PRE style="MARGIN-BOTTOM: 12pt">in error, please immediately alert the sender</PRE><PRE style="MARGIN-BOTTOM: 12pt"> by reply e-mail and then delete this message </PRE><PRE style="MARGIN-BOTTOM: 12pt">and any attachments. If you are not the </PRE><PRE style="MARGIN-BOTTOM: 12pt">intended recipient, you are notified that </PRE><PRE style="MARGIN-BOTTOM: 12pt">any use, dissemination, distribution, copying, </PRE><PRE style="MARGIN-BOTTOM: 12pt">or storage of this message or any attachment </PRE><PRE style="MARGIN-BOTTOM: 12pt">is strictly prohibited.</PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE><PRE style="MARGIN-BOTTOM: 12pt"> </PRE></DIV>
<P class=ecxMsoNormal> </P></DIV></DIV>
<DIV>
<P class=ecxMsoNormal style="MARGIN-BOTTOM: 12pt">_______________________________________________<BR>cisco-voip mailing list<BR><A href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</A><BR><A href="https://puck.nether.net/mailman/listinfo/cisco-voip">https://puck.nether.net/mailman/listinfo/cisco-voip</A></P></DIV></BLOCKQUOTE></DIV>
<P class=ecxMsoNormal style="MARGIN-BOTTOM: 12pt"><BR><BR>_______________________________________________<BR>cisco-voip mailing list<BR><A href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</A><BR><A href="https://puck.nether.net/mailman/listinfo/cisco-voip">https://puck.nether.net/mailman/listinfo/cisco-voip</A></P></DIV>
<P class=ecxMsoNormal> </P></DIV></DIV></DIV></DIV><PRE style="MARGIN-BOTTOM: 12pt"><BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt">E-MAIL CONFIDENTIALITY NOTICE: <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt"><BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt"> <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt"><BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt"> <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt"><BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt"> <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt"><BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt">The contents of this e-mail message and <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt">any attachments are intended solely for the <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt">addressee(s) and may contain confidential <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt">and/or legally privileged information. If you <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt">are not the intended recipient of this message <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt">or if this message has been addressed to you <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt">in error, please immediately alert the sender<BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt"> by reply e-mail and then delete this message <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt">and any attachments. If you are not the <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt">intended recipient, you are notified that <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt">any use, dissemination, distribution, copying, <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt">or storage of this message or any attachment <BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt">is strictly prohibited.<BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt"><BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt"><BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt"><BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt"><BR>
<BR>
</PRE><PRE style="MARGIN-BOTTOM: 12pt"><BR>
<BR>
</PRE></DIV></DIV></DIV>
<DIV>
<DIV><PRE style="MARGIN-BOTTOM: 12pt"><BR>
E-MAIL CONFIDENTIALITY NOTICE: <BR>
<BR>
<BR>
<BR>
<BR>
<BR>
<BR>
<BR>
The contents of this e-mail message and <BR>
any attachments are intended solely for the <BR>
addressee(s) and may contain confidential <BR>
and/or legally privileged information. If you <BR>
are not the intended recipient of this message <BR>
or if this message has been addressed to you <BR>
in error, please immediately alert the sender<BR>
by reply e-mail and then delete this message <BR>
and any attachments. If you are not the <BR>
intended recipient, you are notified that <BR>
any use, dissemination, distribution, copying, <BR>
or storage of this message or any attachment <BR>
is strictly prohibited.<BR>
<BR>
<BR>
<BR>
<BR>
<BR>
<BR>
</PRE></DIV></DIV></DIV></DIV>
<P class=ecxMsoNormal> </P></DIV></DIV><PRE style="WHITE-SPACE: normal"><BR>E-MAIL CONFIDENTIALITY NOTICE: <BR><BR> <BR><BR> <BR><BR> <BR><BR>The contents of this e-mail message and <BR>any attachments are intended solely for the <BR>addressee(s) and may contain confidential <BR>and/or legally privileged information. If you <BR>are not the intended recipient of this message <BR>or if this message has been addressed to you <BR>in error, please immediately alert the sender<BR> by reply e-mail and then delete this message <BR>and any attachments. If you are not the <BR>intended recipient, you are notified that <BR>any use, dissemination, distribution, copying, <BR>or storage of this message or any attachment <BR>is strictly prohibited.<BR><BR><BR><BR><BR><BR><BR><BR></PRE> <br /><hr />Get a new e-mail account with Hotmail – Free. <a href='http://clk.atdmt.com/UKM/go/197222280/direct/01/' target='_new'>Sign-up now.</a></body>
</html>