Don't know rate for installation. I'm guessing in the range of $125/hr to $200/hr<div><br></div><div>Phase 1</div><div><br></div><div><ul><li>CM 40 hours</li><li>UC 16 hours</li><li>CUPS not sure</li><li>UCCx 300 agents? are you sure you want UCCx? my understanding is the top end with UCCx is 300. Might need to look at UCCE. (Really depends on Scripting / IVR) 16-???? hours.</li>
<li>cucimoc ?? not sure have not done it but guessing around 16 hours if all the M$ stuff is ready to go.</li><li>NEC What kind of connection? Qsig? 4-?? hours Is NEC running correct version etc.</li><li>VGW, H323 or MGCP? 2-6hours</li>
<li>Phones -- Guessing about 30-45 minutes each if you have them configured to unpackage and set on desks. (I would suggest getting a minimum wage kid to do that for you..... save a lot of money). Depending on features etc. the BAT could do it fairly quickly (10-20 minutes each if you include scanning all the phones into the speadsheet)</li>
<li>ER -- Depends on if everything is ready with the PS-ALI DB vendor. 16-?? hours</li><li>Analog -- Wiring can take some time. Not sure of your setup. VG's lets say 2 hours each?</li></ul></div><div><br></div><div>
<br></div><div>If you do it right, Phase two should be a bunch of trained monkeys.</div><div><br><div>Bottom line your looking at a large labor cost.</div><div><br></div><div>Scott</div><div><br></div><div><br><div class="gmail_quote">
On Tue, Aug 17, 2010 at 2:21 PM, Kim Casserly <span dir="ltr"><<a href="mailto:solarwinds321@yahoo.com">solarwinds321@yahoo.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex;">
I know this is a very generic question, but does anyone have a ballpark range<br>
(or percentage of HW cost) of installation costs for a VoIP install? We are<br>
definitely going to bid out the project, but if installation services are over<br>
"X" amount, we have to jump through some additional hoops. We have a rough<br>
estimate of what the cost will be for the hardware based upon our usual discount<br>
off list.<br>
<br>
The project would essentially consist of:<br>
<br>
Phase 1 - VoIP core and Pilot:<br>
<br>
Installation / configuration of CUCM (Qty 4: 1 pub, 3 subs)<br>
Installation, configuration, integration of Unity Connections<br>
Installation of Presence<br>
Setup UCCX (~300 agents)<br>
Integration of Office Communicator through CUCI-MOC<br>
Integration with existing NEC IMX PBX<br>
Configuration of four ISR G2 VGs<br>
Installation of ~300 phones (in pilot)<br>
Installation, configuration of Emergency Responder<br>
Initial setup and testing of VG224s<br>
<br>
<br>
Phase 2 - Remaining campus cutover<br>
<br>
~3500 phones<br>
Phased cut-over based upon building (non-contiguous dial plan in buildings)<br>
~1000 analog lines (terminated in four different locations) with use of VG224s<br>
<br>
<br>
This would be a single-site deployment, with a fairly homogeneous feature-set<br>
across phones (except for a few small groups requiring ACD & intercoms).<br>
<br>
<br>
Thanks in advance for taking the time to respond. Hopefully, the OT post doesn't<br>
offend anyone :-)<br>
<br>
Take care.<br>
<br>
-K<br>
<br>
<br>
<br>
<br>
_______________________________________________<br>
cisco-voip mailing list<br>
<a href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a><br>
<a href="https://puck.nether.net/mailman/listinfo/cisco-voip" target="_blank">https://puck.nether.net/mailman/listinfo/cisco-voip</a><br>
</blockquote></div><br></div></div>