A little known fact is that the # is the default terminator on the gateway.  In CUCM, you have to manually configure this to be a terminator.  An example would be 9.011!#.  (An unknown amount of digits dialing internationally, with the ability to stop the 10 second interdigit timeout with a #).<br>
<br>You need to choose a new default terminator.<br><br>dial-peer terminator A<br><br>(ABCD are valid digits, which make good terminators since nobody dials them).<br><br>-nick<br><br><div class="gmail_quote">On Thu, Sep 16, 2010 at 3:48 PM, Nelson, Mike <span dir="ltr"><<a href="mailto:NelsonMike@bfdp.com">NelsonMike@bfdp.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin: 0pt 0pt 0pt 0.8ex; border-left: 1px solid rgb(204, 204, 204); padding-left: 1ex;">








<div link="blue" vlink="purple" lang="EN-US">

<div>

<p class="MsoNormal">Hi all, </p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">I am using a UCM 6.1(4) with H323
gateway.     I have a RP of #880 that I send to the H323
gateway, a 2951 running 15.1(1)T.   This matches the dial-peer shown below
and is routed out an FXO port:</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">dial-peer voice 20 pots</p>

<p class="MsoNormal"> description ***Paging Interface - ALL Page***</p>

<p class="MsoNormal"> destination-pattern #880$</p>

<p class="MsoNormal"> port 0/3/2</p>

<p class="MsoNormal"> forward-digits 0</p>

<p class="MsoNormal"> prefix 0</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">In normal operation, the call is routed as I would expect
with a 0 being sent to the paging system.    This is also an
SRST gateway and when attached SRST phone dial the same pattern, the call fails
after I dial #8.</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">If I run a debug voice ccapi inout, I see that the pound is
being seen as the character T in the debug.    A debug voice
dialpeer shows that the call fails to find a matching dial-peer.</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">I have searched high and low on the Cisco site and in
Netpro, and I think that I should be OK with the pound in the destination-pattern,
but I must be missing something here…</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">Any help would be greatly appreciated.</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">Thanks,</p>

<p class="MsoNormal"> </p><font color="#888888">

<p class="MsoNormal"><span style="font-size: 12pt;">Mike</span></p>

</font></div>

</div>


<br>_______________________________________________<br>
cisco-voip mailing list<br>
<a href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a><br>
<a href="https://puck.nether.net/mailman/listinfo/cisco-voip" target="_blank">https://puck.nether.net/mailman/listinfo/cisco-voip</a><br>
<br></blockquote></div><br>