Paul/ccieidot1,<br><br>well I have a fsx voice-port of (but not in use)<br><br><b style="color: rgb(0, 0, 153);">voice-port 0/0/0<br>! <br>voice-port 0/0/1<br>! <br>voice-port 0/0/2</b><br>! <br><b style="color: rgb(0, 0, 153);">voice-port 0/0/3</b><br>
!<br>and an E1 interface of... (connected to remote router)<br><br><b style="color: rgb(0, 0, 153);">controller E1 0/2/0<br> framing NO-CRC4 <br> channel-group 0 timeslots 1-31<br> !<br> interface Serial0/2/0:0<br> description G703.E1.Connection to Customer router<br>
bandwidth 2048<br> no ip address<br>encap HDLC</b><br>!<br>I am using the E1 interface to connect to a remote router with E1 interface too at the other end with above config<br><br>May challenge is, I want to configure a dial-peer that will route all my voice traffic destined to 1000 through the E1 card, so i configure the following....<br>
<br><b><span style="color: rgb(0, 0, 153);">dial-peer voice 1 pots</span><br style="color: rgb(0, 0, 153);"><span style="color: rgb(0, 0, 153);">destination-pattern 21232</span><br style="color: rgb(0, 0, 153);"><span style="color: rgb(0, 0, 153);">session target port 0/0/0:0<br>
!<br></span></b><span style="color: rgb(0, 0, 0);">but saw the following error....</span><b><span style="color: rgb(0, 0, 153);"><br><br>MY_ROUTER(config-dial-peer)#session target port 0/2/0:0 <br> ^<br>
% Invalid input detected at '^' marker.<br><br></span></b><span style="color: rgb(0, 0, 0);">Also when I use <b style="color: rgb(0, 0, 153);">port 0/2/0:0</b> as advised by ccieidot1, I receive the following message..</span><span style="color: rgb(0, 0, 153);"></span><b><span style="color: rgb(0, 0, 153);"><br>
<br>MY_ROUTER(config-dial-peer)#port 0/2/0:0 <br> ^<br>% Invalid input detected at '^' marker.<br>!<br></span></b><br>Please assist, as what I want to achieve is to route all voice traffic destined to 1000 at the remote site through the E1 interface.<br>
<br> <br><br><br><br><br clear="all"><b><span style="font-family: georgia,serif; color: rgb(0, 0, 102);">Cheers,</span><br style="font-family: georgia,serif; color: rgb(0, 0, 102);"><span style="font-family: georgia,serif; color: rgb(0, 0, 102);">Idowu Kehinde</span><br style="font-family: georgia,serif; color: rgb(0, 0, 102);">
<span style="font-family: georgia,serif; color: rgb(0, 0, 102);">TEL: 2348024017748</span><br style="font-family: georgia,serif; color: rgb(0, 0, 102);"><span style="font-family: georgia,serif; color: rgb(0, 0, 102);">BB: 30E8E5F9</span><br>
</b><br> <br>
<br><br><div class="gmail_quote">On Mon, Feb 7, 2011 at 7:09 PM, Paul <span dir="ltr"><<a href="mailto:asobihoudai@yahoo.com">asobihoudai@yahoo.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin: 0pt 0pt 0pt 0.8ex; border-left: 1px solid rgb(204, 204, 204); padding-left: 1ex;">
<div><div style="font-family: 'times new roman','new york',times,serif; font-size: 12pt;"><div>What is the label on your voice-port?</div><div><br></div><div>I'm going to guess that your voice-port is also 0/2/0:0...I've never touched an E1 so I am a little bit confused when I don't see :31 at the end instead of the "0" you have there but..it looks like you're trying to send calls to a voice port that doesn't exist and you're trying to use session target when that's used for voip dial peers.</div>
<div><br></div><div>You're looking for</div><div class="im"><div>port 0/2/0:0 instead.</div></div><div style="font-family: times new roman,new york,times,serif; font-size: 12pt;"><br><div style="font-family: times new roman,new york,times,serif; font-size: 12pt;">
<font face="Tahoma" size="2"><hr size="1"><b><span style="font-weight: bold;">From:</span></b><span> Just Kennie <<a href="mailto:justkennie@gmail.com" target="_blank">justkennie@gmail.com</a>></span><br><b><span style="font-weight: bold;">To:</span></b><span> <a href="mailto:cisco-voip@puck.nether.net" target="_blank">cisco-voip@puck.nether.net</a></span><br>
<b><span style="font-weight: bold;">Sent:</span></b> Mon, February 7, 2011 10:00:42 AM<br><b><span style="font-weight: bold;">Subject:</span></b> [cisco-voip] dial-peer E1 ISDN<br></font><div><div></div><div class="h5"><br>
Hi All,<br>I am trying to configure my E1 card for ISDN connectivity for voice traffic, below is my config...<br><br><b style="color: rgb(0, 0, 153);">controller E1 0/2/0<br> framing NO-CRC4 <br> channel-group 0 timeslots 1-31<br>
!<br>interface Serial0/2/0:0<br> description G703.E1.Connection to Customer<br> bandwidth 2048<br> no ip address</b><br><b style="color: rgb(0, 0, 153);">encapp HDLC</b><br><b>!</b><br>Now I am trying to configure the Dial-peer, to forward 2123 calls through the E1 ISDN interface<br>
!<br><b><span style="color: rgb(0, 0, 153);">dial-peer voice 1 pots</span><br style="color: rgb(0, 0, 153);"><span style="color: rgb(0, 0, 153);">destination-pattern 21232</span><br style="color: rgb(0, 0, 153);"><span style="color: rgb(0, 0, 153);">session target port 0/0/0:0</span></b><br>
! <br>but its my 2811 voice gateway is not allowing the "session target port 0/0/0:0" command, please what should I do to forward my calls through the E1 ISDN interface.<br><br><br><br clear="all"><b><span style="font-family: georgia,serif; color: rgb(0, 0, 102);">Cheers,</span><br style="font-family: georgia,serif; color: rgb(0, 0, 102);">
<span style="font-family: georgia,serif; color: rgb(0, 0, 102);">Idowu Kehinde</span><br style="font-family: georgia,serif; color: rgb(0, 0, 102);"><span style="font-family: georgia,serif; color: rgb(0, 0, 102);">TEL: 2348024017748</span><br style="font-family: georgia,serif; color: rgb(0, 0, 102);">
<span style="font-family: georgia,serif; color: rgb(0, 0, 102);">BB: 30E8E5F9</span><br></b><br> <br>
</div></div></div></div><div></div>
</div><br>
</div></blockquote></div><br>