<html><head></head><body style="word-wrap: break-word; -webkit-nbsp-mode: space; -webkit-line-break: after-white-space; ">Hi Nick,<div><br></div><div>Set your 'Calling Party Transform Mask' on the outbound Route Pattern in UCM to your SIP Connect ID (i.e. 99.......)</div><div><br></div><div>That should set the From Header in the outbound request so Skype will accept your call</div><div><br></div><div>You can use 'debug ccsip message' on the CUBE gateway to check the FROM header is being set correctly.</div><div><br></div><div>Thanks</div><div><br></div><div>Stephen</div><div><br><div><div>On 3 Mar 2011, at 04:08, Nick Matthews wrote:</div><br class="Apple-interchange-newline"><blockquote type="cite">I would put a no sip-register on your pots dial peers to make it clean. All those guys are going to try and register by default.<br><br>If you have ephone-dn's you can put no-reg on the number as well, same deal.<br><br>
You may want to create a dummy pots line or ephone-dn with the correct From: DID to get it to send the register message. Then you do some translation/forwarding to get it where you want it.<br><br>-nick<br><br><div class="gmail_quote">
On Wed, Mar 2, 2011 at 9:30 PM, Robert Kulagowski <span dir="ltr"><<a href="mailto:rkulagow@gmail.com">rkulagow@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex;">
<div class="im">On Tue, Mar 1, 2011 at 3:33 PM, Stephen Welsh<br>
<<a href="mailto:stephen.welsh@unifiedfx.com">stephen.welsh@unifiedfx.com</a>> wrote:<br>
> I've configured Skype Connect using a CUBE config (SIP2SIP) directly on the internet, I did it for the same reasons are yourself, however I was disappointed at the cost (to actually place calls) and the fact you cannot call to a Skype User ID from the IP-PBX (you can do the reverse by calling your Skype Connect ID number from any Skype Client). I was hoping to do some Single Number Reach with my Skype ID :(<br>
><br>
> Below are the relevant parts from my working config, however you need to add your own security statements (I'm not responsible for your phone bill :), you will most likely be exposing port 5060/61 to the Wide Wicked Web, and I've seen a LOT of registration attempts hit my router....<br>
><br>
<br>
</div>So, after a "wr erase" and a reboot, then starting from scratch, I've<br>
at least got the REGISTER part sending my Skype Connect username<br>
rather than my dial peers.<br>
<br>
The next part to figure out is if they're rejecting my "from"; it<br>
looks like when I send an INVITE to them I send my internal 6-digit<br>
extension and I end up getting a reject. Is there something else that<br>
I'm missing from my config? Are they expecting the FROM to be my<br>
Skype ID, with the TO being the <a href="mailto:e.164destination@sip.skype.com">e.164destination@sip.skype.com</a>?<br>
<div><div></div><div class="h5"><br>
_______________________________________________<br>
cisco-voip mailing list<br>
<a href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a><br>
<a href="https://puck.nether.net/mailman/listinfo/cisco-voip" target="_blank">https://puck.nether.net/mailman/listinfo/cisco-voip</a><br>
</div></div></blockquote></div><br>
</blockquote></div><br></div></body></html>