Yes, that is the confirmation I was looking for, thank you.<br><br><div class="gmail_quote">On Thu, Jul 28, 2011 at 1:20 PM, Dockendorf, Dave <span dir="ltr"><<a href="mailto:Dave.Dockendorf@ecolab.com">Dave.Dockendorf@ecolab.com</a>></span> wrote:<br>

<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex;"><div lang="EN-US" link="blue" vlink="purple"><div><p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D">Charles,<u></u><u></u></span></p>

<p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D">The following command will busy-out the b channels, but it will not disconnect until the call terminates.<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D"><u></u> <u></u></span></p>

<p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D">Start off in global config mode, and change to your D-Channel interface:<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D"><u></u> <u></u></span></p>

<p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D">                voice_gw(config)# interface Serial0/1:23 (whatever your voice PRI is)<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D"><u></u> <u></u></span></p>

<p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D">Then, issue your busyout command. Here, I’m placing all my channels out of service:<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D"><u></u> <u></u></span></p>

<p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D">                voice_gw(config-if)# isdn service b_channel 0-23 state 2 soft<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D"><u></u> <u></u></span></p>

<p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D">(b_channel=0-23 – This is my range. You can certainly just insert one channel, or a different range.)<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D"><u></u> <u></u></span></p>

<p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D">                state=2 – 0=InService, 1=Maint, 2=OutOfService<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D"><u></u> <u></u></span></p>

<p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D">                soft – This means, place them in the defined state, when the channel becomes idle. (in other words, do not disconnnect active channels until they hang up)<u></u><u></u></span></p>

<p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D">                ***if the router resets after you have done this, this will clear to normal operation when the router comes back up.***<u></u><u></u></span></p>

<p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D">Hope this helps!<u></u><u></u></span></p><p class="MsoNormal">
<span style="font-size:11.0pt;color:#1F497D"><u></u> <u></u></span></p>
<p class="MsoNormal"><span style="font-size:11.0pt;color:#1F497D"><u></u> </span></p></div></div></blockquote></div>