<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META content="text/html; charset=iso-8859-1" http-equiv=Content-Type>
<META name=GENERATOR content="MSHTML 8.00.6001.19298">
<STYLE></STYLE>
</HEAD>
<BODY>
<DIV><FONT size=2 face=Arial>Okay, so we are generating a PRI an an AS5400 media
gateway and delivering it to an IAD2400 at the customer site. There are three
channels on the PRI, which is reflected in the trunkgroup status.</FONT></DIV>
<DIV><FONT size=2 face=Arial></FONT> </DIV>
<DIV><FONT size=2 face="Courier New">controller T1 1/0:19<BR> framing
esf<BR> channel-group 0 timeslots 1-15 speed 64<BR> loopback network
ignore<BR> pri-group timeslots 21-24<BR> description Combo PRI T1 to
Allied Aluminum.<BR></FONT></DIV>
<DIV><FONT size=2 face="Courier New">interface
Serial1/0:19:23<BR> description PRI to Allied Aluminum<BR> no ip
address<BR> isdn switch-type primary-ni<BR> isdn protocol-emulate
network<BR> isdn incoming-voice modem<BR> trunk-group
Allied<BR> no cdp enable<BR></FONT></DIV>
<DIV><FONT size=2 face="Courier New">dial-peer voice 6202
pots<BR> description ' Analog PBX Trunk Allied Aluminum
Products:ALUM-03-BT1-AMP-POTS<BR> incoming called-number
5025681100<BR> direct-inward-dial<BR> forward-digits
all<BR>!<BR>dial-peer voice 6203 pots<BR> trunkgroup Allied<BR> tone
ringback alert-no-PI<BR> description ' Analog PBX Trunk Allied Aluminum
Products:ALUM-03-BT1-AMP-POTS<BR> translation-profile incoming
AddPriServNumPI<BR> incoming called-number
5025681100<BR> destination-pattern
5025681100<BR> direct-inward-dial<BR> forward-digits
all<BR></FONT></DIV>
<DIV><FONT size=2></FONT> </DIV>
<DIV><FONT size=2 face="Courier New"></FONT> </DIV>
<DIV><FONT size=2 face="Courier New">ArmoryPl-AS5400#show trunk group
Allied<BR>Trunk group: Allied<BR>
Description:<BR> trunk group label:
Allied</FONT></DIV>
<DIV><FONT size=2 face="Courier New"></FONT> </DIV>
<DIV><FONT size=2 face="Courier New">
Translation profile (Incoming):<BR>
Translation profile (Outgoing):</FONT></DIV>
<DIV><FONT size=2 face="Courier New"></FONT> </DIV>
<DIV><FONT size=2 face="Courier New">
Hunt Scheme is sequential both up<BR>
Max Calls (Incoming): NOT-SET (Any) NOT-SET (Voice)
NOT-SET (Data)<BR> Max Calls
(Outgoing): NOT-SET (Any) NOT-SET (Voice) NOT-SET
(Data)<BR> Retries: 3</FONT></DIV>
<DIV><FONT size=2 face="Courier New"></FONT> </DIV>
<DIV><FONT size=2 face="Courier New">
Trunk Se1/0:19:23 Preference
DEFAULT<BR>
Total channels available :
3<BR>
Data = 0, Voice = 0, Modem = 0, Pending = 0, Free = 3</FONT></DIV>
<DIV><FONT size=2 face="Courier New"></FONT> </DIV>
<DIV><FONT size=2 face="Courier New">
Total calls for trunk group: Data = 0, Voice = 0, Modem =
0<BR>
Pend = 0, Free = 3</FONT></DIV>
<DIV><FONT size=2 face=Arial></FONT> </DIV>
<DIV><FONT size=2 face=Arial></FONT> </DIV>
<DIV><FONT size=2 face=Arial>When we make three calls to the customer,
everything works fine. All three calls go through as they should and show up as
they should.</FONT></DIV>
<DIV><FONT size=2 face=Arial></FONT> </DIV>
<DIV><FONT size=2 face="Courier New">ArmoryPl-AS5400#show voice call
status<BR>CallID CID
ccVdb Port
DSP/Ch Called # Codec
Dial-peers<BR>0x6B23 2C5B 0x64F5CD00 1/0:1:D.5 No
dsp 5025681100 None
6202/6203<BR>0x6B24 2C5B 0x666585D8 1/0:19:D. No dsp
*5025681100 None
6203/6202<BR>0x6B25 2C5E 0x64F5CD00 1/0:1:D.6 No
dsp 5025681100 None
6202/6203<BR>0x6B26 2C5E 0x666585D8 1/0:19:D. No dsp
*5025681100 None
6203/6202<BR>0x6B29 2C62 0x64F5CD00 1/0:1:D.7 No
dsp 5025681100 None
6202/6203<BR>0x6B2A 2C62 0x666585D8 1/0:19:D. No dsp
*5025681100 None 6203/6202<BR></FONT></DIV>
<DIV><FONT size=2 face=Arial>The thing is, when we place a 4th call, instead of
getting the expected busy signal, the AS5400 media gateway gives a beep and
disconnect. If no channels are available, shouldn't the media gateway be
generating a busy signal? Or do we have to specifically tell it to do that in
some way?</FONT></DIV>
<DIV><FONT size=2 face=Arial> </DIV></FONT></BODY></HTML>