For calls inbound to FXO ports, you would need to configure connection plar.<br><br><div class="gmail_quote">On Mon, Feb 25, 2013 at 10:38 AM, Jeffrey Girard <span dir="ltr"><<a href="mailto:jeffrey.girard@girardinc.com" target="_blank">jeffrey.girard@girardinc.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div>
<div style="direction:ltr;font-size:10pt;font-family:Tahoma">
<p>Simplified diagram is attached. Lab network.</p>
<p style="PADDING-BOTTOM:0px;MIN-HEIGHT:8pt;PADDING-LEFT:0px;PADDING-RIGHT:0px;min-height:8pt;PADDING-TOP:0px">
</p>
<p>Scenario: Using a 2811 router as a PSTN emulator. Has a 2 port FXS card installed. One port has an analog phone attached, other port is connected to a 4 port FXO card installed into a 2951 router. 2951 is H323 with CUCM 8.6. Simple/test dial peers configured.
Snippets below:</p>
<p style="PADDING-BOTTOM:0px;MIN-HEIGHT:8pt;PADDING-LEFT:0px;PADDING-RIGHT:0px;min-height:8pt;PADDING-TOP:0px">
</p>
<p>PSTN Emulator:</p>
<p>!</p>
<p>voice-port 0/0/0</p>
<p>!</p>
<p>voice-port 0/0/1</p>
<p>!</p>
<p>!</p>
<p>!</p>
<p>!</p>
<p>dial-peer voice 1 pots</p>
<p>description Emulating legacy PATCOM number</p>
<p>destination-pattern 0999</p>
<p>port 0/0/1</p>
<p>!</p>
<p>dial-peer voice 2 pots</p>
<p>description Emulating tie line to Access Terminal</p>
<p>destination-pattern 9999</p>
<p>port 0/0/0</p>
<p style="PADDING-BOTTOM:0px;MIN-HEIGHT:8pt;PADDING-LEFT:0px;PADDING-RIGHT:0px;min-height:8pt;PADDING-TOP:0px">
</p>
<p>H323 Gateway Router</p>
<p>!</p>
<p>voice-port 0/1/0</p>
<p>trunk-group FXO</p>
<p>cptone PK</p>
<p>!</p>
<p>voice-port 0/1/1</p>
<p>trunk-group FXO</p>
<p>cptone PK</p>
<p>!</p>
<p>voice-port 0/1/2</p>
<p>trunk-group FXO</p>
<p>cptone PK</p>
<p>!</p>
<p>voice-port 0/1/3</p>
<p>trunk-group FXO</p>
<p>cptone PK</p>
<p>!</p>
<p>!</p>
<p>dial-peer voice 1 pots</p>
<p>description Incoming Call Routing</p>
<p>incoming called-number .</p>
<p>direct-inward-dial</p>
<p>!</p>
<p>dial-peer voice 2 voip</p>
<p>description Incoming Call Routing</p>
<p>incoming called-number .</p>
<p>voice-class codec 1 </p>
<p>dtmf-relay h245-alphanumeric</p>
<p>no vad</p>
<p>!</p>
<p>!<br>
voice-port 0/1/0<br>
trunk-group FXO<br>
cptone PK<br>
!<br>
voice-port 0/1/1<br>
trunk-group FXO<br>
cptone PK<br>
!<br>
voice-port 0/1/2<br>
trunk-group FXO<br>
cptone PK<br>
!<br>
voice-port 0/1/3<br>
trunk-group FXO<br>
cptone PK<br>
!</p>
<p>!</p>
<p>dial-peer voice 999 pots</p>
<p>description Dummy dial peer to test BYOPBX</p>
<p>destination-pattern 0999</p>
<p>port 0/1/0</p>
<p>forward-digits all</p>
<p>!</p>
<p style="PADDING-BOTTOM:0px;MIN-HEIGHT:8pt;PADDING-LEFT:0px;PADDING-RIGHT:0px;min-height:8pt;PADDING-TOP:0px">
</p>
<p>I have other dial-peers on this router (not shown) that will take the inbound digits. However, Im never able to pass the digits.</p>
<p style="PADDING-BOTTOM:0px;MIN-HEIGHT:8pt;PADDING-LEFT:0px;PADDING-RIGHT:0px;min-height:8pt;PADDING-TOP:0px">
</p>
<p>Calls from the VoIP network to the simulated PSTN work fine. Calls from the PSTN to the VoIP network fail.
</p>
<p style="PADDING-BOTTOM:0px;MIN-HEIGHT:8pt;PADDING-LEFT:0px;PADDING-RIGHT:0px;min-height:8pt;PADDING-TOP:0px">
</p>
<p>When I pick up the analog phone, I get the expected dial tone. I enter "9999" and the call rings to the FXS port and I hear the FXO port answer. I get the expected secondary (2 stage) dial tone, but then before I can press any digits, the FXo port hangs
up and I am left with the PSTN router dial tone.</p>
<p style="PADDING-BOTTOM:0px;MIN-HEIGHT:8pt;PADDING-LEFT:0px;PADDING-RIGHT:0px;min-height:8pt;PADDING-TOP:0px">
</p>
<p>debug voip dialpeer on the H323 router shows no results at all when I try to place the call.</p>
<p>debug voip dialpeer on the PSTN router shows the expected dial peer matching and the expected result. File is attached.</p>
<p style="PADDING-BOTTOM:0px;MIN-HEIGHT:8pt;PADDING-LEFT:0px;PADDING-RIGHT:0px;min-height:8pt;PADDING-TOP:0px">
</p>
<p>Additionally, when I observe the output of show voice port summary while I place the call, I see the FXS port (the one that is tied to the FXO port) go off hook and then go back on hook (file also attached)</p>
<p style="PADDING-BOTTOM:0px;MIN-HEIGHT:8pt;PADDING-LEFT:0px;PADDING-RIGHT:0px;min-height:8pt;PADDING-TOP:0px">
</p>
<p>So, the FXO port appears to be looking for something from the FXS when it answers the call, doesnt get it (or doesnt like what it gets) so it hangs up.</p>
<p style="PADDING-BOTTOM:0px;MIN-HEIGHT:8pt;PADDING-LEFT:0px;PADDING-RIGHT:0px;min-height:8pt;PADDING-TOP:0px">
</p>
<p>Looking for help...</p>
<p style="PADDING-BOTTOM:0px;MIN-HEIGHT:8pt;PADDING-LEFT:0px;PADDING-RIGHT:0px;min-height:8pt;PADDING-TOP:0px">
</p>
<p>Jeff</p>
</div>
</div>
<br>_______________________________________________<br>
cisco-voip mailing list<br>
<a href="mailto:cisco-voip@puck.nether.net">cisco-voip@puck.nether.net</a><br>
<a href="https://puck.nether.net/mailman/listinfo/cisco-voip" target="_blank">https://puck.nether.net/mailman/listinfo/cisco-voip</a><br>
<br></blockquote></div><br><br clear="all"><br>-- <br>duy<br>CCIE #27737 Voice<br>