What I have done in some past upgrades is to copy/paste everything on Device Defaults page (or screen shot it). Deactivate TFTP service on all nodes - so it can't even start following any necessary reboots. Install the upgrade. Go back to Device Defaults page and set everything back how you like it. Activate TFTP service on all nodes where you had previously deactivated it. <div><br></div><div>HTH,</div><div>Dave<span></span><br><br>On Saturday, January 3, 2015, Ryan Huff <<a href="mailto:ryanhuff@outlook.com">ryanhuff@outlook.com</a>> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">


<div><div dir="ltr">Correct, ordinarily that would be what I would do as well. In this case though, I am trying to avoid upgrading the firmware on anything, other than the devices I am trying to get support for.<br><br>Thanks,<br><br>Ryan<br><br><div><hr>Date: Sat, 3 Jan 2015 14:20:43 -0600<br>From: <a href="javascript:_e(%7B%7D,'cvml','brez@brezworks.com');" target="_blank">brez@brezworks.com</a><br>To: <a href="javascript:_e(%7B%7D,'cvml','cisco-voip@puck.nether.net');" target="_blank">cisco-voip@puck.nether.net</a><br>Subject: Re: [cisco-voip] Device pack installation methodology question<br><br>
  
    
  
  
    <div>On 1/3/2015 2:11 PM, Ryan Huff wrote:<br>
    </div>
    <blockquote>
      
      <div dir="ltr">I need to install a device pack on a 2 node 9.1(2)
        CCM cluster to get support for some 88xx phones but I do not
        want to update the loads for anything else.<br>
        <br>
        The approach I am going to use is:<br>
        <br>
        Drop the publisher out of the CM Group, forcing all phones to
        the subscriber. Install the device pack on the publisher and
        reboot the publisher. Once the publisher is backup, set all the
        device defaults back to what I want them to be then add the
        publisher back to the CM Group. Then drop the subscriber from
        the CM Group forcing all the phones on the publisher and start
        the install process over for the subscriber. Once everything is
        back up add the subscriber back to the CM Group.<br>
        <br>
        Does that sound reasonable or is there an easier way?<br>
      </div>
    </blockquote>
    <br>
    Any time I've needed device support I just install it on all the
    nodes then reboot them one at a time during a maintenance window. 
    As long as both nodes are running call processing, they'll fail over
    when the node reboots.  Not sure about on 9.X, but on 10.X this just
    shows as a blip on the phones of them reregistering, not a full
    reboot.  Obviously if you install new software for those phones,
    they'll upgrade software when they reboot.<br>
    <br>
    Jeremy "TheBrez" Bresley<br>
    <a href="javascript:_e(%7B%7D,'cvml','brez@brezworks.com');" target="_blank">brez@brezworks.com</a><br>
  

<br>_______________________________________________
cisco-voip mailing list
<a href="javascript:_e(%7B%7D,'cvml','cisco-voip@puck.nether.net');" target="_blank">cisco-voip@puck.nether.net</a>
<a href="https://puck.nether.net/mailman/listinfo/cisco-voip" target="_blank">https://puck.nether.net/mailman/listinfo/cisco-voip</a></div>                                         </div></div>
</blockquote></div>