<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=iso-8859-1">
<style type="text/css" style="display:none;"><!-- P {margin-top:0;margin-bottom:0;} --></style>
</head>
<body dir="ltr">
<div id="divtagdefaultwrapper" style="font-size:12pt;color:#000000;background-color:#FFFFFF;font-family:Calibri,Arial,Helvetica,sans-serif;">
<p>Hi Aaron!</p>
<p><br>
</p>
<p>With a 3850 stack in an environment like you describe, the config I would likely do on the interface (unless I had some mitigating reason to do otherwise) would look like:</p>
<p><br>
</p>
<p>rthtestlab# conf t</p>
<p>rthtestlab(config)# ip multicast-routing</p>
<p>rthtestlab(config)# int gi1/0/10<br>
</p>
<p>rthtestlab(config-if)# ip pim sparse-mode</p>
<p>rthtestlab(config-if)# end</p>
<p>rthtestlab#<br>
</p>
<p><br>
</p>
<p>(keep in mind that if you do use sparse-mode, you will need a rendezvous point)
<br>
</p>
<p><br>
</p>
<p>IGMP (Internet Group Management Protocol) registers individual hosts in a multicast group on a particular LAN (VLAN). Enabling PIM on an interface also enables IGMP. IGMP also limits the flow of multicast traffic through the segment using things called,
"queriers" and "hosts"; in order to participate in multicasting, the device (in this case a 3850 stack) must have IGMP running.</p>
<p><br>
</p>
<p>I would take some time and review <a href="http://www.cisco.com/en/US/docs/switches/lan/catalyst3850/software/release/3se/consolidated_guide/b_consolidated_3850_3se_cg_chapter_0101000.html#topic_046CCC6211D149DBAD2E9D7F22C7306D">
http://www.cisco.com/en/US/docs/switches/lan/catalyst3850/software/release/3se/consolidated_guide/b_consolidated_3850_3se_cg_chapter_0101000.html#topic_046CCC6211D149DBAD2E9D7F22C7306D</a> (multicast on 3850). There are a number of road-bumps you could encounter
with multicast that could have you scratching your head.</p>
<p><br>
</p>
<p>Another tip with these IP paging solutions is that most of them (Singlewire being one) require the web server on the IP phone to be enabled. Something that can get overlooked sometimes.<br>
</p>
<p><br>
</p>
<p><br>
</p>
<div id="Signature">
<div id="divtagdefaultwrapper" style="font-size:12pt; color:#000000; background-color:#FFFFFF; font-family:Calibri,Arial,Helvetica,sans-serif">
= Ryan =
<p><br>
</p>
<p><br>
</p>
<p>Email: ryanthomashuff@outlook.com</p>
<p>Spark: ryanthomashuff@outlook.com</p>
<p>Twitter: <a id="LPNoLP" href="http://twitter.com/ryanthomashuff">@ryanthomashuff</a><br>
</p>
<p>LinkedIn: <a id="LPNoLP" href="http://linkedin.com/in/ryanthomashuff">ryanthomashuff</a><br>
</p>
<p>Web <a title="Ctrl+Click or tap to follow the link" id="LPNoLP" href="http://ryanthomashuff.com">
ryanthomashuff.com</a></p>
</div>
</div>
<br>
<br>
<div style="color: rgb(0, 0, 0);">
<hr tabindex="-1" style="display:inline-block; width:98%">
<div id="divRplyFwdMsg" dir="ltr"><font style="font-size:11pt" face="Calibri, sans-serif" color="#000000"><b>From:</b> cisco-voip <cisco-voip-bounces@puck.nether.net> on behalf of Aaron Banks <amichaelbanks@hotmail.com><br>
<b>Sent:</b> Monday, December 7, 2015 2:26 PM<br>
<b>To:</b> cisco-voip@puck.nether.net<br>
<b>Subject:</b> [cisco-voip] Informacast</font>
<div> </div>
</div>
<div>
<div dir="ltr">I've never configured Informacast before. I have most of the setup complete, the only piece I'm hung up on is the 3850 switch (which is stacked). I want to enable multicast but it is only for the voice vlan. There is no routing being done
between vlans or multiple switches. Do I use ip multicast routing to enable multicasting globally or ip multicast auto-enable? Also, is PIM or IGMP normally used? IGMP is already running, so I was thinking I only had to configure the multicast address for
it.<br>
<br>
Aaron<br>
<br>
<div><br>
<br>
</div>
</div>
</div>
</div>
</div>
</body>
</html>