<div dir="ltr">According to the debug, you're calling 19529473283. Is that correct?<div><br></div><div><pre class="inbox-inbox-ndfHFb-c4YZDc-pf-DARUcf" style="font-family:"Courier New",Courier,monospace,arial,sans-serif;margin-top:0px;margin-bottom:0px;white-space:pre-wrap;word-wrap:break-word;font-size:14px">Called Number=19529473283(TON=Unknown, NPI=Unknown),</pre><div><br></div><div>If so, then this debug is not for this gateway, because you're hitting Outgoing Dial-peer=5</div><div><br></div><div><pre class="inbox-inbox-ndfHFb-c4YZDc-pf-DARUcf" style="font-family:"Courier New",Courier,monospace,arial,sans-serif;margin-top:0px;margin-bottom:0px;white-space:pre-wrap;word-wrap:break-word;font-size:14px">Outgoing Dial-peer=5, Params=0x688FF3FC, Progress Indication=ORIGINATING SIDE IS NON ISDN(3)</pre></div><div><br></div><div>And dial-peer 5, while it exists in your config you pasted, it doesn't match the called number.</div><div><br></div><div><div><font face="monospace">dial-peer voice 5 voip</font></div><div><font face="monospace"> description FXO test</font></div><div><font face="monospace"> destination-pattern 12083437020</font></div><div><font face="monospace"> session target ipv4:10.0.2.5</font></div></div><div><font face="monospace">!</font></div><div><br></div><div>Even if it did match the destination pattern, you're missing some config on this dial-peer to make a SIP capable dial-peer, which means it's sending H323 setup to CUCM. If you built the gateway as H323, then I can see how it rang your CIPC, otherwise, if you built it as SIP, which you said you did, then it would never ring your CIPC.</div><div><br></div><div>So, something is not adding up here.</div><div><br></div><div>Also, you're hitting Incoming Dial-peer=0, which on a POTS leg is not too terrible, but it's also not good practice to be using dial-peer 0. It's really VoIP DP 0 that is messy though.<br></div><div><br></div><div><pre class="inbox-inbox-ndfHFb-c4YZDc-pf-DARUcf" style="font-family:"Courier New",Courier,monospace,arial,sans-serif;margin-top:0px;margin-bottom:0px;white-space:pre-wrap;word-wrap:break-word;font-size:14px">Incoming Dial-peer=0, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), Calling IE Present=FALSE,</pre></div><div><br></div></div></div><br><div class="gmail_quote"><div dir="ltr">On Thu, Mar 1, 2018 at 10:06 AM Hamu Ebiso <<a href="mailto:hebiso2010@hotmail.com">hebiso2010@hotmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div dir="ltr">
<div id="m_935747933123784071divtagdefaultwrapper" style="font-size:12pt;color:#000000;font-family:Calibri,Helvetica,sans-serif" dir="ltr">
<p style="margin-top:0px;margin-bottom:0px">Hi Anthony,</p>
<p style="margin-top:0px;margin-bottom:0px"><br>
</p>
<p style="margin-top:0px;margin-bottom:0px">yes the call was hitting the gateway because I was seeing FXO port going Off-Hook. The problem was that Logging was not setup in the gateway. After I setup the Logging, I'm now seeing logs.</p>
<p style="margin-top:0px;margin-bottom:0px"><br>
</p>
<p style="margin-top:0px;margin-bottom:0px">I have attached the log.<br>
</p>
<p><br>
thanks</p>
<p>Hamu<br>
</p>
<div style="color:rgb(0,0,0)">
<hr style="width:98%;display:inline-block">
<div id="m_935747933123784071divRplyFwdMsg" dir="ltr"><font color="#000000" face="Calibri, sans-serif" style="font-size:11pt"><b>From:</b> <a href="mailto:avholloway@gmail.com" target="_blank">avholloway@gmail.com</a> <<a href="mailto:avholloway@gmail.com" target="_blank">avholloway@gmail.com</a>> on behalf of Anthony Holloway <<a href="mailto:avholloway%2Bcisco-voip@gmail.com" target="_blank">avholloway+cisco-voip@gmail.com</a>><br>
<b>Sent:</b> Thursday, March 1, 2018 8:45 AM<br>
<b>To:</b> Hamu Ebiso<br>
<b>Cc:</b> Cisco VoIP Group</font></div></div></div></div><div dir="ltr"><div id="m_935747933123784071divtagdefaultwrapper" style="font-size:12pt;color:#000000;font-family:Calibri,Helvetica,sans-serif" dir="ltr"><div style="color:rgb(0,0,0)"><div id="m_935747933123784071divRplyFwdMsg" dir="ltr"><font color="#000000" face="Calibri, sans-serif" style="font-size:11pt"><br>
<b>Subject:</b> Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router</font></div></div></div></div><div dir="ltr"><div id="m_935747933123784071divtagdefaultwrapper" style="font-size:12pt;color:#000000;font-family:Calibri,Helvetica,sans-serif" dir="ltr"><div style="color:rgb(0,0,0)">
<div>
<div dir="auto">Since you didn't see the call in your debugs, your call likely didn't hit your gateway.
<div dir="auto"><br>
</div>
<div dir="auto">Can you confirm how you made your test call, when you had your debug running?</div>
</div>
<div class="m_935747933123784071x_gmail_extra"><br>
<div class="m_935747933123784071x_gmail_quote">On Feb 28, 2018 2:46 PM, "Hamu Ebiso" <<a id="m_935747933123784071LPlnk705549" href="mailto:hebiso2010@hotmail.com" target="_blank">hebiso2010@hotmail.com</a>> wrote:<br type="attribution">
<blockquote class="m_935747933123784071x_gmail_quote" style="margin:0px 0px 0px 0.8ex;padding-left:1ex;border-left-color:rgb(204,204,204);border-left-width:1px;border-left-style:solid">
<div dir="ltr">
<div id="m_935747933123784071x_m_3941368411824381705divtagdefaultwrapper" style="color:rgb(0,0,0);font-family:Calibri,Helvetica,sans-serif;font-size:12pt" dir="ltr">
<p style="margin-top:0px;margin-bottom:0px"></p>
<div>Here is the dial-peer output</div>
<div><br>
</div>
<div>1#show run | sec dial-peer<br>
dial-peer voice 1 pots<br>
trunkgroup FXO_EM<br>
translation-profile incoming Inbound<br>
call-block translation-profile incoming block_profile<br>
call-block disconnect-cause incoming call-reject<br>
incoming called-number .<br>
direct-inward-dial<br>
dial-peer voice 911 pots<br>
trunkgroup FXO_EM<br>
description Services<br>
translation-profile outgoing Strip9<br>
destination-pattern 911<br>
dial-peer voice 9911 pots<br>
trunkgroup FXO_EM<br>
description Services<br>
translation-profile outgoing Strip9<br>
destination-pattern 9911<br>
dial-peer voice 2 voip<br>
description CUCM Dial-Peer - Inbound<br>
preference 1<br>
destination-pattern <a id="m_935747933123784071LPlnk150292" href="tel:(208)%20685-8038" value="+12086858038" target="_blank">
12086858038</a><br>
session protocol sipv2<br>
session target ipv4:10.0.2.6<br>
incoming uri via 10<br>
voice-class codec 1<br>
dtmf-relay rtp-nte sip-kpml<br>
fax-relay ecm disable<br>
fax nsf 000000<br>
ip qos dscp cs3 signaling<br>
no vad<br>
dial-peer voice 3 voip<br>
preference 2<br>
destination-pattern <a id="m_935747933123784071LPlnk617522" href="tel:(208)%20685-8038" value="+12086858038" target="_blank">
12086858038</a><br>
session target ipv4:10.0.2.3<br>
dial-peer voice 650 pots<br>
trunkgroup Local<br>
description Local outbound<br>
translation-profile outgoing Strip9<br>
destination-pattern 9208.......<br>
dial-peer voice 4 pots<br>
trunkgroup FXO_EM<br>
description ** 10-digit Local Call **<br>
translation-profile outgoing Strip9<br>
destination-pattern ^9[2-9]..[2-9]......$<br>
forward-digits 10<br>
dial-peer voice 5 voip<br>
description FXO test<br>
destination-pattern <a id="m_935747933123784071LPlnk981920" href="tel:(208)%20343-7020" value="+12083437020" target="_blank">
12083437020</a><br>
session target ipv4:10.0.2.5<br>
</div>
<p></p>
<p><br>
</p>
thank you very much!!<br>
<br>
<div style="color:rgb(0,0,0)">
<hr style="width:98%;display:inline-block">
<div id="m_935747933123784071x_m_3941368411824381705divRplyFwdMsg" dir="ltr"><font color="#000000" face="Calibri, sans-serif" style="font-size:11pt"><b>From:</b> Anthony Holloway <<a id="m_935747933123784071LPlnk658822" href="mailto:avholloway%2Bcisco-voip@gmail.com" target="_blank">avholloway+cisco-voip@gmail.com</a>><br>
<b>Sent:</b> Wednesday, February 28, 2018 1:29 PM<br>
<b>To:</b> Hamu Ebiso<br>
<b>Cc:</b> cisco-voip voyp list<br>
<b>Subject:</b> Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router</font>
<div> </div>
</div>
<div>
<div dir="ltr">Maybe you're actually using MGCP then? You still haven't shown the dial-peers on the gateway. Is that because you don't have any?
<div><br>
</div>
<div>show run | section dial-peer<br>
<br>
<div class="m_935747933123784071x_m_3941368411824381705x_gmail_quote">
<div dir="ltr">On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso <<a id="m_935747933123784071LPlnk338820" href="mailto:hebiso2010@hotmail.com" target="_blank">hebiso2010@hotmail.com</a>> wrote:<br>
</div>
<blockquote class="m_935747933123784071x_m_3941368411824381705x_gmail_quote" style="margin:0px 0px 0px 0.8ex;padding-left:1ex;border-left-color:rgb(204,204,204);border-left-width:1px;border-left-style:solid">
<div dir="ltr">
<div id="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463divtagdefaultwrapper" style="color:rgb(0,0,0);font-family:Calibri,Helvetica,sans-serif;font-size:12pt" dir="ltr">
<p style="margin-top:0px;margin-bottom:0px">debug was turned on as shown below.</p>
<p style="margin-top:0px;margin-bottom:0px"><br>
</p>
<p style="margin-top:0px;margin-bottom:0px"></p>
<div>1#debug voice ccapi inout<br>
voip ccapi inout debugging is on</div>
<div><br>
</div>
<div>made test calls and then show log, I see below output.<br>
</div>
<p></p>
<p></p>
<p>1#show log<br>
Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)</p>
<p>No Active Message Discriminator.</p>
<p><br>
</p>
<p>No Inactive Message Discriminator.</p>
<p><br>
Console logging: level debugging, 517 messages logged, xml disabled,<br>
filtering disabled<br>
Monitor logging: level debugging, 0 messages logged, xml disabled,<br>
filtering disabled<br>
Buffer logging: level debugging, 550 messages logged, xml disabled,<br>
filtering disabled<br>
Exception Logging: size (4096 bytes)<br>
Count and timestamp logging messages: disabled<br>
Persistent logging: disabled</p>
<p>No active filter modules.</p>
<p> Trap logging: level debugging, 620 message lines logged<br>
Logging to 10.0.7.139 (udp port 514, audit disabled,<br>
link up),<br>
435 message lines logged,<br>
0 message lines rate-limited,<br>
0 message lines dropped-by-MD,<br>
xml disabled, sequence number disabled<br>
filtering disabled<br>
Logging to 10.0.8.12 (udp port 514, audit disabled,<br>
link up),<br>
435 message lines logged,<br>
0 message lines rate-limited,<br>
0 message lines dropped-by-MD,<br>
xml disabled, sequence number disabled<br>
filtering disabled<br>
Logging Source-Interface: VRF Name:<br>
Loopback0<br>
</p>
<p></p>
<p><br>
</p>
<p>I don't see any calls activity.</p>
<p><br>
</p>
<p>thanks<br>
<br>
</p>
<div style="color:rgb(0,0,0)">
<hr style="width:98%;display:inline-block">
<div id="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463divRplyFwdMsg" dir="ltr"><font color="#000000" face="Calibri, sans-serif" style="font-size:11pt"><b>From:</b> Anthony Holloway <<a id="m_935747933123784071LPlnk77564" href="mailto:avholloway%2Bcisco-voip@gmail.com" target="_blank">avholloway+cisco-voip@gmail.com</a>><br>
<b>Sent:</b> Wednesday, February 28, 2018 11:19 AM</font></div>
</div>
</div>
</div>
<div dir="ltr">
<div id="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463divtagdefaultwrapper" style="color:rgb(0,0,0);font-family:Calibri,Helvetica,sans-serif;font-size:12pt" dir="ltr">
<div style="color:rgb(0,0,0)">
<div id="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463divRplyFwdMsg" dir="ltr"><font color="#000000" face="Calibri, sans-serif" style="font-size:11pt"><br>
<b>To:</b> Hamu Ebiso<br>
<b>Cc:</b> cisco-voip voyp list<br>
<b>Subject:</b> Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router</font></div>
</div>
</div>
</div>
<div dir="ltr">
<div id="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463divtagdefaultwrapper" style="color:rgb(0,0,0);font-family:Calibri,Helvetica,sans-serif;font-size:12pt" dir="ltr">
<div style="color:rgb(0,0,0)">
<div>
<div dir="ltr">But you didn't send all the information, because your output doesn't show the dial-peers.
<div><br>
</div>
<div>One method is to capture the output from "debug voip ccapi inout" and look for the following line "Outgoing Dial-peer="</div>
<div><br>
</div>
<div>You also didn't address the regions either. Can you send that too?</div>
</div>
<br>
<div class="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463x_gmail_quote">
<div dir="ltr">On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso <<a id="m_935747933123784071LPlnk524963" href="mailto:hebiso2010@hotmail.com" target="_blank">hebiso2010@hotmail.com</a>> wrote:<br>
</div>
<blockquote class="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463x_gmail_quote" style="margin:0px 0px 0px 0.8ex;padding-left:1ex;border-left-color:rgb(204,204,204);border-left-width:1px;border-left-style:solid">
<div dir="ltr">
<div id="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463x_m_2219273772835208879divtagdefaultwrapper" style="color:rgb(0,0,0);font-family:Calibri,Helvetica,sans-serif;font-size:12pt" dir="ltr">
<p style="margin-top:0px;margin-bottom:0px">I was just trying to give you all the information so that you will be able to see the whole picture.</p>
<p style="margin-top:0px;margin-bottom:0px">Regarding your questions, I don't know how to check that.<br>
</p>
<br>
<br>
<div style="color:rgb(0,0,0)">
<hr style="width:98%;display:inline-block">
<div id="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463x_m_2219273772835208879divRplyFwdMsg" dir="ltr">
<font color="#000000" face="Calibri, sans-serif" style="font-size:11pt"><b>From:</b> Anthony Holloway <<a id="m_935747933123784071LPlnk976586" href="mailto:avholloway%2Bcisco-voip@gmail.com" target="_blank">avholloway+cisco-voip@gmail.com</a>><br>
<b>Sent:</b> Wednesday, February 28, 2018 10:45 AM</font></div>
</div>
</div>
</div>
<div dir="ltr">
<div id="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463x_m_2219273772835208879divtagdefaultwrapper" style="color:rgb(0,0,0);font-family:Calibri,Helvetica,sans-serif;font-size:12pt" dir="ltr">
<div style="color:rgb(0,0,0)">
<div id="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463x_m_2219273772835208879divRplyFwdMsg" dir="ltr">
<font color="#000000" face="Calibri, sans-serif" style="font-size:11pt"><br>
<b>To:</b> Hamu Ebiso<br>
<b>Cc:</b> cisco-voip voyp list<br>
<b>Subject:</b> Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router</font></div>
</div>
</div>
</div>
<div dir="ltr">
<div id="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463x_m_2219273772835208879divtagdefaultwrapper" style="color:rgb(0,0,0);font-family:Calibri,Helvetica,sans-serif;font-size:12pt" dir="ltr">
<div style="color:rgb(0,0,0)">
<div>
<div dir="ltr">That's interesting that I asked for the dial-peer config, and you sent everything but.
<div><br>
</div>
<div>Do you know how to confirm which dial-peer the gateway is using?</div>
</div>
<br>
<div class="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463x_m_2219273772835208879x_gmail_quote">
<div dir="ltr">On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso <<a id="m_935747933123784071LPlnk282690" href="mailto:hebiso2010@hotmail.com" target="_blank">hebiso2010@hotmail.com</a>> wrote:<br>
</div>
<blockquote class="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463x_m_2219273772835208879x_gmail_quote" style="margin:0px 0px 0px 0.8ex;padding-left:1ex;border-left-color:rgb(204,204,204);border-left-width:1px;border-left-style:solid">
<div dir="ltr">
<div id="m_935747933123784071x_m_3941368411824381705x_m_6475442122256384463x_m_2219273772835208879x_m_-8897566770194573471divtagdefaultwrapper" style="color:rgb(0,0,0);font-family:Calibri,Helvetica,sans-serif;font-size:12pt" dir="ltr">
<p style="margin-top:0px;margin-bottom:0px">Below is gateway configuration</p>
<p style="margin-top:0px;margin-bottom:0px"><br>
</p>
<p style="margin-top:0px;margin-bottom:0px"><br>
</p>
<p style="margin-top:0px;margin-bottom:0px"><br>
</p>
<p style="margin-top:0px;margin-bottom:0px"></p>
<div>
<div>isdn switch-type primary-ni<br>
!<br>
!<br>
trunk group FXO_EM<br>
hunt-scheme sequential<br>
translation-profile incoming Incoming<br>
!<br>
!<br>
trunk group Local<br>
hunt-scheme sequential<br>
translation-profile outgoing outbound<br>
!<br>
!<br>
trunk group LD<br>
translation-profile outgoing outbound<br>
!<br>
voice-card 0<br>
dspfarm<br>
dsp services dspfarm<br>
!<br>
!<br>
voice call send-alert<br>
voice rtp send-recv<br>
!<br>
voice service voip<br>
ip address trusted list<br>
ipv4 10.170.99.12<br>
ipv4 10.44.50.14<br>
ipv4 10.44.50.39<br>
no ip address trusted authenticate<br>
clid substitute name<br>
clid network-provided<br>
allow-connections h323 to h323<br>
allow-connections h323 to sip<br>
allow-connections sip to h323<br>
allow-connections sip to sip<br>
redirect ip2ip<br>
signaling forward unconditional<br>
fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw<br>
no fax-relay sg3-to-g3<br>
modem passthrough nse codec g711ulaw<br>
sip<br>
bind control source-interface Loopback0<br>
bind media source-interface Loopback0<br>
session transport tcp<br>
min-se 360 session-expires 360<br>
ds0-num<br>
header-passing<br>
error-passthru<br>
registrar server expires max 600 min 60<br>
early-offer forced<br>
midcall-signaling passthru<br>
no call service stop<br>
!<br>
!<br>
voice class uri 10 sip<br>
host ipv4:10.x.x.x<br>
host ipv4:10..x.x.x<br>
host ipv4:10..x.x.x<br>
voice class codec 1<br>
codec preference 1 g711ulaw<br>
codec preference 2 g729r8<br>
!<br>
voice class codec 2<br>
codec preference 1 g711ulaw<br>
!<br>
!<br>
!<br>
!<br>
voice translation-rule 1<br>
rule 1 /^208343\(....\)$/ /1208343\1/<br>
!<br>
voice translation-rule 9<br>
rule 1 /5.../ /1208343\0/<br>
!<br>
voice translation-rule 10<br>
rule 1 /^911/ /911/<br>
rule 2 /^9911/ /911/<br>
!<br>
voice translation-rule 15<br>
!<br>
voice translation-rule 30<br>
rule 1 /^911/ /911/<br>
rule 2 /^9911/ /911/<br>
rule 4 /^9\(011.*\)/ /\1/<br>
rule 9 /^9\(.*\)/ /\1/<br>
!<br>
!<br>
voice translation-profile Add1<br>
translate calling 91<br>
translate called 1<br>
!<br>
voice translation-profile Inbound<br>
translate called 1<br>
!<br>
voice translation-profile Strip9<br>
translate called 10<br>
!<br>
voice translation-profile block_profile<br>
translate calling 15<br>
!<br>
voice translation-profile outbound<br>
translate calling 10<br>
!<br>
!<br>
crypto pki token default removal timeout 0<br>
!<br>
!<br>
!<br>
!<br>
license udi pid CISCO3845-MB sn FOC123128X5<br>
license accept end user agreement<br>
archive<br>
log config<br>
hidekeys<br>
username admin privilege 15 password 7 105D1F0C<br>
username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx.<br>
!<br>
!<br>
controller T1 0/0/0<br>
shutdown<br>
cablelength long 0db<br>
!<br>
controller T1 0/1/0<br>
shutdown<br>
cablelength long 0db<br>
!<br>
!<br>
!<br>
!<br>
!<br>
!<br>
interface Loopback0<br>
ip address 10.x.x.x 255.255.255.128<br>
!<br>
interface GigabitEthernet0/0<br>
description uplink to Lan1<br>
ip address 10.x.x.x 255.255.255.252<br>
duplex auto<br>
speed auto<br>
media-type rj45<br>
!<br>
interface GigabitEthernet0/1<br>
description uplink to Lan2<br>
ip address 10.x.x.x 255.255.255.252<br>
duplex auto<br>
speed auto<br>
media-type rj45<br>
!<br>
router ospf 1<br>
auto-cost reference-bandwidth 10000<br>
network 10.0.0.0 0.0.255.255 area 10.0.0.0<br>
!<br>
ip forward-protocol nd<br>
!<br>
!<br>
no ip http server<br>
no ip http secure-server<br>
!</div>
<div><br>
</div>
<div><br>
</div>
</div>
<p></p>
</div>
</div>
</blockquote>
</div>
</div>
</div>
</div>
</div>
</blockquote>
</div>
</div>
</div>
</div>
</div>
</blockquote>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</blockquote>
</div>
</div>
</div>
</div></div></div></blockquote></div>