<div dir="auto">You want the MFT which is the Multi-Function Trunk card. </div><div dir="auto"><br></div><div dir="auto">Make sure you pick it under the voice card section of CCW and then pick the PVDM4-256. </div><div dir="auto"><br></div><div dir="auto">Andrew</div><div dir="auto"><br></div><div><br><div class="gmail_quote"><div>On Wed, May 9, 2018 at 10:29 AM PF <<a href="mailto:pucknether@foril.com">pucknether@foril.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><u></u>
<div bgcolor="#ffffff">
<div><font size="2" face="Arial">Hi again</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">We are preparing the hardware request</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">I am not sure, should we get </font>NIM-8MFT-T1/E1
modules or NIM-8CE1T1-PRI modules ?</div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">the clear-channel vs channellized channel is not
clear for me</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">thanks</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">Pat</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial"></font> </div>
<blockquote style="BORDER-LEFT:#000000 2px solid;PADDING-LEFT:5px;PADDING-RIGHT:0px;MARGIN-LEFT:5px;MARGIN-RIGHT:0px"></blockquote></div><div bgcolor="#ffffff"><blockquote style="BORDER-LEFT:#000000 2px solid;PADDING-LEFT:5px;PADDING-RIGHT:0px;MARGIN-LEFT:5px;MARGIN-RIGHT:0px">
<div style="FONT:10pt arial">----- Original Message ----- </div>
<div style="FONT:10pt arial;BACKGROUND:#e4e4e4"><b>From:</b>
<a title="vtadorsett@gmail.com" href="mailto:vtadorsett@gmail.com" target="_blank">Andrew
Dorsett</a> </div>
</blockquote></div><div bgcolor="#ffffff"><blockquote style="BORDER-LEFT:#000000 2px solid;PADDING-LEFT:5px;PADDING-RIGHT:0px;MARGIN-LEFT:5px;MARGIN-RIGHT:0px"><div style="FONT:10pt arial"><b>To:</b> <a title="pucknether@foril.com" href="mailto:pucknether@foril.com" target="_blank">PF</a> </div>
<div style="FONT:10pt arial"><b>Cc:</b> <a title="ryanhuff@outlook.com" href="mailto:ryanhuff@outlook.com" target="_blank">Ryan Huff</a> ; <a title="cisco-voip@puck.nether.net" href="mailto:cisco-voip@puck.nether.net" target="_blank">cisco-voip@puck.nether.net</a> </div>
<div style="FONT:10pt arial"><b>Sent:</b> Friday, May 04, 2018 3:39 PM</div>
<div style="FONT:10pt arial"><b>Subject:</b> Re: [cisco-voip] ISDN T1 voice
calls hardware validation</div>
<div><br></div>
<div dir="auto">Pat -</div>
<div dir="auto">Also let’s look at the hypothetical ASR you’re wanting versus
the ISR. <br></div>
<div dir="auto"><br></div>
<div dir="auto">The ASR1006 supports 12 half height SPAs in 6RU of space.</div>
<div dir="auto"><br></div>
<div dir="auto">To keep this simple and not get into codec complexity, let’s
assume that the DSP SPA is matched 1:1 with the 8xT1 SPA. </div>
<div dir="auto"><br></div>
<div dir="auto">That gives us 6 8xT1 SPAs providing a total of 48 T1 ports and
1,104 PRI channels in the 6RU. </div>
<div dir="auto"><br></div>
<div dir="auto">The ISR4451 supports 5 8xT1 NIMs providing a total of 40 T1
ports and 920 channels in 2RU. </div>
<div dir="auto"><br></div>
<div dir="auto">Three ISR4451 boxes would give us a total of 120 T1 ports versus
the 48 in a single ASR1006 for the same rack density.</div>
<div dir="auto"><br></div>
<div dir="auto">Hopefully you see the reason why the ASR just isn’t the right
platform for voice T1 termination. Now SBC is a totally different story
and you can chock it full of DSP SPAs and make a huge transcoder which the ISR
can’t do because it doesn’t have enough DSPs.</div>
<div dir="auto"><br></div>
<div dir="auto">Andrew </div>
<div dir="auto"><br></div>
<div><br>
<div class="gmail_quote">
<div>On Fri, May 4, 2018 at 2:47 PM PF <<a href="mailto:pucknether@foril.com" target="_blank">pucknether@foril.com</a>>
wrote:<br></div>
<blockquote style="BORDER-LEFT:#ccc 1px solid;MARGIN:0px 0px 0px 0.8ex;PADDING-LEFT:1ex" class="gmail_quote"><u></u>
<div bgcolor="#ffffff">
<div><font size="2" face="Arial">ok</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">I guess we will have to look for another
product like the ISR4k</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">the ASR1006 was very interresting because
it was full redundant</font></div>
<div><font size="2" face="Arial">and we could put several 8xT1 card in it to
have greater density</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">the ISR4k seems to be limited to 3 cards and is
not redundant.</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">Pat</font></div></div>
<div bgcolor="#ffffff">
<div><font size="2" face="Arial"></font> </div>
<blockquote style="BORDER-LEFT:#000000 2px solid;PADDING-LEFT:5px;PADDING-RIGHT:0px;MARGIN-LEFT:5px;MARGIN-RIGHT:0px">
<div style="FONT:10pt arial">----- Original Message ----- </div>
<div style="FONT:10pt arial;BACKGROUND:#e4e4e4"><b>From:</b> <a title="vtadorsett@gmail.com" href="mailto:vtadorsett@gmail.com" target="_blank">Andrew Dorsett</a> </div>
<div style="FONT:10pt arial"><b>To:</b> <a title="ryanhuff@outlook.com" href="mailto:ryanhuff@outlook.com" target="_blank">Ryan Huff</a> </div>
<div style="FONT:10pt arial"><b>Cc:</b> <a title="pucknether@foril.com" href="mailto:pucknether@foril.com" target="_blank">PF</a> ; <a title="cisco-voip@puck.nether.net" href="mailto:cisco-voip@puck.nether.net" target="_blank">cisco-voip@puck.nether.net</a> </div>
<div style="FONT:10pt arial"><b>Sent:</b> Friday, May 04, 2018 12:45
PM</div>
<div style="FONT:10pt arial"><b>Subject:</b> Re: [cisco-voip] ISDN T1
voice calls hardware validation</div>
<div><br></div>
<div dir="auto">I replied privately but the SPA-DSP was built for SBC
transcoding using CUBE between SIP or H323 trunks. Unless something
has changed recently it cannot be linked to the T1 SPA to terminate PRI
Voice. </div>
<div dir="auto"><br></div>
<div dir="auto">To terminate voice from a PRI you will need to use one of
the ISR products and the relevant T1 module with DSPs. If you’re using the
latest it would be an ISR4k with the NIM first mentioned and make sure the
DSPs are onboard the NIM. </div>
<div dir="auto"><br></div>
<div dir="auto">Andrew</div>
<div dir="auto"><br></div>
<div><br>
<div class="gmail_quote">
<div>On Fri, May 4, 2018 at 12:32 PM Ryan Huff <<a href="mailto:ryanhuff@outlook.com" target="_blank">ryanhuff@outlook.com</a>> wrote:<br></div>
<blockquote style="BORDER-LEFT:#ccc 1px solid;MARGIN:0px 0px 0px 0.8ex;PADDING-LEFT:1ex" class="gmail_quote">
<div dir="auto">Not sure if DSP is onboard the SPA like the NIM; I’d have
to look that one up ... you might try <span><i>dsp services dspfarm
</i>under the voice-card configuration parameter. I’d also disable cdp
on the serial interface.</span>
<div><br></div>
<div>
<div id="m_-791668719044147223m_-2162305688662135849m_8553762886255870531AppleMailSignature">Sent
from my iPhone</div></div></div>
<div dir="auto">
<div>
<div><br>On May 4, 2018, at 12:18, PF <<a href="mailto:pucknether@foril.com" target="_blank">pucknether@foril.com</a>> wrote:<br><br></div>
<blockquote type="cite">
<div>
<div><font size="2" face="Arial">Hi</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">I have tried several
configurations</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">Here is the relevent par of the actual
config</font></div>
<div><font size="2" face="Arial"><br>version 15.3<br>boot system flash
bootflash:asr1000rp2-adventerprisek9.03.10.07.S.153-3.S7-ext.bin<br>!<br>card
type t1 0 2<br>!<br>multilink bundle-name authenticated<br>isdn
switch-type primary-5ess<br>!<br>voice-card 0/0<br>!<br>voice service
pots<br> supported-language FR<br>!<br>voice service
voip<br> clid network-provided<br> allow-connections h323 to
sip<br> allow-connections sip to h323<br> allow-connections
sip to sip<br> signaling forward
unconditional<br> sip<br> bind control source-interface
GigabitEthernet1/2/0<br> bind media source-interface
GigabitEthernet1/2/0<br> ds0-num<br>
header-passing<br> privacy id<br> outbound-proxy
ipv4:172.16.x.y<br>!<br>voice class codec 1<br> codec preference
1 g711ulaw<br>!<br>controller T1 0/2/0<br> framing
esf<br> clock source internal<br> linecode
b8zs<br> cablelength long 0db<br> pri-group timeslots
1-24<br>!<br>interface Service-Engine0/0/0<br>!<br>interface
Serial0/2/0:23<br> encapsulation hdlc<br> isdn switch-type
primary-5ess<br> isdn negotiate-bchan<br>!<br>map-class dialer
DOVtest<br> dialer voice-call<br>!<br>dspfarm profile 1 transcode
universal <br> rsvp<br> shutdown<br>!<br>dial-peer
voice 1 voip<br> destination-pattern *.<br> signaling
forward unconditional<br> session protocol sipv2<br> session
target sip-server<br> voice-class codec 1
<br>!<br>dial-peer voice 2 pots<br> destination-pattern
xxxxxxx<br> incoming called-number
xxxxxxx<br> direct-inward-dial<br>!<br>!<br>sip-ua
<br> credentials username asr1006 password 7 xxxxxxxx realm
yyyyy<br> retry invite 3<br> retry bye 3<br> retry
cancel 3<br> timers trying 1000<br> timers register
100<br> sip-server ipv4:172.16.x.y<br>!<br>!</font></div><font size="2" face="Arial">
<div>Pat</div></font>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial"></font> </div>
<blockquote style="BORDER-LEFT:#000000 2px solid;PADDING-LEFT:5px;PADDING-RIGHT:0px;MARGIN-LEFT:5px;MARGIN-RIGHT:0px">
<div style="FONT:10pt arial">----- Original Message ----- </div>
<div style="FONT:10pt arial;BACKGROUND:#e4e4e4"><b>From:</b> <a title="ryanhuff@outlook.com" href="mailto:ryanhuff@outlook.com" target="_blank">Ryan Huff</a> </div>
<div style="FONT:10pt arial"><b>To:</b> <a title="pfortin@royaume.com" href="mailto:pfortin@royaume.com" target="_blank">Patrick Fortin</a> </div>
<div style="FONT:10pt arial"><b>Cc:</b> <a title="cisco-voip@puck.nether.net" href="mailto:cisco-voip@puck.nether.net" target="_blank">cisco-voip@puck.nether.net</a> </div>
<div style="FONT:10pt arial"><b>Sent:</b> Friday, May 04, 2018
11:43 AM</div>
<div style="FONT:10pt arial"><b>Subject:</b> Re: [cisco-voip] ISDN
T1 voice calls hardware validation</div>
<div><br></div>I assume you have the card type specified and
controller interface configured with timeslots?
<div><br></div>
<div>Can you send the running-config and code version?<br><br>
<div id="m_-791668719044147223m_-2162305688662135849m_8553762886255870531AppleMailSignature">Sent
from my iPhone</div>
<div><br>On May 4, 2018, at 11:35, Patrick Fortin <<a href="mailto:pfortin@royaume.com" target="_blank">pfortin@royaume.com</a>> wrote:<br><br></div>
<blockquote type="cite">
<div>
<div><font size="2" face="Arial">Hi</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">I get this error</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial"> **ERROR**: call_incoming:
Received a call id 0x2F with a bad bearercap from xxxxxxxxxx
on b channel 1</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">seems like the dsp are not associated
with the t1 card</font></div>
<div><font size="2" face="Arial"><br>in the config we don't have acces
to the following :</font></div><font size="2" face="Arial"></font>
<div><font size="2" face="Arial">
<p>isdn incoming-voice voice<br>which should go on the Serial
interface. <br><br>we also don't have the "port" command that
should go in the dial-peer voice section</p></font></div>
<div><font size="2" face="Arial">any ideas ?</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">Thanks</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">Pat</font></div>
<blockquote style="BORDER-LEFT:#000000 2px solid;PADDING-LEFT:5px;PADDING-RIGHT:0px;MARGIN-LEFT:5px;MARGIN-RIGHT:0px">
<div style="FONT:10pt arial">----- Original Message -----
</div>
<div style="FONT:10pt arial;BACKGROUND:#e4e4e4"><b>From:</b>
<a title="ryanhuff@outlook.com" href="mailto:ryanhuff@outlook.com" target="_blank">Ryan Huff</a> </div>
<div style="FONT:10pt arial"><b>To:</b> <a title="pucknether@foril.com" href="mailto:pucknether@foril.com" target="_blank">PF</a> </div>
<div style="FONT:10pt arial"><b>Cc:</b> <a title="cisco-voip@puck.nether.net" href="mailto:cisco-voip@puck.nether.net" target="_blank">cisco-voip@puck.nether.net</a> </div>
<div style="FONT:10pt arial"><b>Sent:</b> Friday, May 04, 2018
11:11 AM</div>
<div style="FONT:10pt arial"><b>Subject:</b> Re: [cisco-voip]
ISDN T1 voice calls hardware validation</div>
<div><br></div>That correct! I misread! Yeah the shared port
adapter T1 should work.
<div><br><br>
<div id="m_-791668719044147223m_-2162305688662135849m_8553762886255870531AppleMailSignature">Sent
from my iPhone</div>
<div><br>On May 4, 2018, at 10:36, PF <<a href="mailto:pucknether@foril.com" target="_blank">pucknether@foril.com</a>> wrote:<br><br></div>
<blockquote type="cite">
<div>
<div><font size="2" face="Arial">Hi</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">Thanks for your help</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">But there are no NIM slot in the
ASR1006 chassis</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">NIM is for ASR1001-X I
think</font></div>
<div><font size="2" face="Arial"></font> </div>
<div><font size="2" face="Arial">Pat</font></div>
<div><font size="2" face="Arial"></font> </div>
<blockquote style="BORDER-LEFT:#000000 2px solid;PADDING-LEFT:5px;PADDING-RIGHT:0px;MARGIN-LEFT:5px;MARGIN-RIGHT:0px">
<div style="FONT:10pt arial">----- Original Message -----
</div>
<div style="FONT:10pt arial;BACKGROUND:#e4e4e4"><b>From:</b>
<a title="ryanhuff@outlook.com" href="mailto:ryanhuff@outlook.com" target="_blank">Ryan
Huff</a> </div>
<div style="FONT:10pt arial"><b>To:</b> <a title="pucknether@foril.com" href="mailto:pucknether@foril.com" target="_blank">PF</a>
</div>
<div style="FONT:10pt arial"><b>Cc:</b> <a title="cisco-voip@puck.nether.net" href="mailto:cisco-voip@puck.nether.net" target="_blank">cisco-voip@puck.nether.net</a> </div>
<div style="FONT:10pt arial"><b>Sent:</b> Friday, May 04,
2018 9:56 AM</div>
<div style="FONT:10pt arial"><b>Subject:</b> Re:
[cisco-voip] ISDN T1 voice calls hardware validation</div>
<div><br></div>For isdn voice you’ll need a
NIM-8MFT-T1/E1<br><br>
<div id="m_-791668719044147223m_-2162305688662135849m_8553762886255870531AppleMailSignature">Sent
from my iPhone</div>
<div><br>On May 4, 2018, at 09:31, PF <<a href="mailto:pucknether@foril.com" target="_blank">pucknether@foril.com</a>>
wrote:<br><br></div>
<blockquote type="cite">
<div>
<div><font size="2" face="Arial">
<div>Hi</div>
<div>
<p>Can someone help us validate if we can use this
hardware to receive voice calls from a isdn T1 (23B+D) and
send them in SIP to a softswitch and vice-versa</p>
<p>ASR1006<br>SPA-8XCHT1/E1<br>SPA-DSP<br>ASR1000-RP2<br>ASR1000-ESP40</p>
<p>in short can it be used to build a voip gateway like an
audiocode mediant or a patton smartnode</p>
<p>Thanks</p>
<p>Pat</p></div></font></div></div></blockquote>
<blockquote type="cite">
<div><span>_______________________________________________</span><br><span>cisco-voip
mailing list</span><br><span><a href="mailto:cisco-voip@puck.nether.net" target="_blank">cisco-voip@puck.nether.net</a></span><br><span><a href="https://puck.nether.net/mailman/listinfo/cisco-voip" target="_blank">https://puck.nether.net/mailman/listinfo/cisco-voip</a></span><br></div></blockquote></blockquote></div></blockquote></div></blockquote></div></blockquote></div></blockquote></div></blockquote></div></div>_______________________________________________<br>cisco-voip
mailing list<br><a href="mailto:cisco-voip@puck.nether.net" target="_blank">cisco-voip@puck.nether.net</a><br><a href="https://puck.nether.net/mailman/listinfo/cisco-voip" rel="noreferrer" target="_blank">https://puck.nether.net/mailman/listinfo/cisco-voip</a><br></blockquote></div></div></blockquote></div></blockquote></div></div></blockquote></div></blockquote></div></div>