<div dir="ltr">Roger:<br><br>Thanks I was looking in the command guide did not think about the userguide.<br><br>RootNet08<br><br><div class="gmail_quote">On Fri, Aug 29, 2008 at 2:14 AM, Roger Wiklund <span dir="ltr"><<a href="mailto:roger.wiklund@gmail.com">roger.wiklund@gmail.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;"><div>The VLAN mgmt comes pre configured with only the 10/100 UTP management port as a member.</div>
<div> </div>
<div>Just config an IP address on that VLAN and connect your pc to it.</div>
<div> </div>
<div>I would try to run an extended diagnostics, maybe try to upgrade to the latest EW image.</div>
<div> </div>
<div>Check out the Extremeware documents here: <a href="http://www.extremenetworks.com/services/software-userguide.aspx" target="_blank">http://www.extremenetworks.com/services/software-userguide.aspx</a></div>
<div> </div>
<div>But chances are that the switch has been damaged.</div>
<div> </div>
<div>Regards</div>
<div> </div>
<div>Roger</div>
<div> </div>
<div><br><br> </div>
<div><div><div></div><div class="Wj3C7c"><span class="gmail_quote">On 8/29/08, <b class="gmail_sendername">root net</b> <<a href="mailto:rootnet08@gmail.com" target="_blank">rootnet08@gmail.com</a>> wrote:</span>
</div></div><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0px 0px 0px 0.8ex; padding-left: 1ex;"><div><div></div><div class="Wj3C7c">
<div dir="ltr">Hello,<br><br>I have checked the archives from 2003 to now and could not find this anywhere. Here is my problem:<br><br>I have a Extreme Summit 400-48t lost power for about 5-12 secs (UPS failure/problem) but powered back on after power was restored and none of the ports worked. I have an exact copy of this switch running as well and it fired back up without a problem unlike this one.<br>
<br>Here are sample logs:<br><br>09/26/2007 16:11:34.23 <Erro> <EDP.ProcPDUFail> pdu received on port 2 could not be processed, checksum error on port 2<br>09/25/2007 11:10:18.43 <Erro> <EDP.ProcPDUFail> pdu received on port 2 could not be processed, checksum error on port 2<br>
09/25/2007 10:20:02.55 <Erro> <EDP.ProcPDUFail> pdu received on port 2 could not be processed, checksum error on port 2<br>09/24/2007 23:50:41.30 <Erro> <EDP.ProcPDUFail> pdu received on port 2 could not be processed, checksum error on port 2<br>
09/20/2007 13:43:49.85 <Erro> <EDP.ProcPDUFail<br><br>BTW I wiped the config and the time is off now so ignore that.<br><br>What do you think is wrong? How can I procure? I thought about reloading the image but can not use the ports to do a tftp. Can some one explain also how to configure the management port on the back to do this if possible. I am a Cisco person not extreme but I am learning. <br>
<br>Thanks in advanced!!!<br><br>--RootNet08<br> </div><br></div></div>_______________________________________________<br>extreme-nsp mailing list<br><a href="mailto:extreme-nsp@puck.nether.net" target="_blank">extreme-nsp@puck.nether.net</a><br>
<a href="https://puck.nether.net/mailman/listinfo/extreme-nsp" target="_blank">https://puck.nether.net/mailman/listinfo/extreme-nsp</a><br></blockquote></div><br>
</blockquote></div><br></div>