[f-nsp] MLX-16 LP cards revert to CARD_STATE_REBOOT
goverton at nwi.net
goverton at nwi.net
Wed Nov 28 11:24:29 EST 2007
S16: NI-MLX-1Gx20-GC 20-port 10/100/1000 Copper Module CARD_STATE_DOWN
(5) (previous state = CARD_STATE_BOOT)
Card State Down Reason Code:
0 CARD_DOWN_REASON_NONE
1 CARD_DOWN_REASON_ADMIN_DOWN
2 CARD_DOWN_REASON_CONFIG_MISMATCH
3 CARD_DOWN_REASON_LOSS_HEARTBEAT
4 CARD_DOWN_REASON_BOOT_FAILED
5 CARD_DOWN_REASON_TIMEOUT
6 CARD_DOWN_REASON_STRIPE_SYNC_FAILED
7 CARD_DOWN_REASON_REBOOTED
8 CARD_DOWN_REASON_OVER_HEAT
9 CARD_DOWN_REASON_POWERED_OFF_BY_USER
10 CARD_DOWN_REASON_LINK_DOWN
LP-16 Monitor>reset
NetIron XMR/MLX Boot Monitor Version 3.5.00b
Enter 'b' to stop at boot monitor
sent IPC_MSGTYPE_REBOOT to slot 16 (my_slot = 15, ipc_post_rx32_mode = 0)
received IPC_MSGTYPE_REBOOT_ACK from fid d020
REV B LP
get_module_type: board_class = cc 204 27
ipc_send_card_boot: module_type = 27
REV B LP
get_module_type: board_class = cc 204 27
PPCR type = 2, xtm_arg = 1, xpp_arg = 0, pbif_arg = 0, xgmac_arg = 0,
hv_cam_type = ff, hv_value = 0
sent IPC_MSGTYPE_LP_CARD_BOOT to slot 32
Received IPC_MSGTYPE_MP_CARD_BOOT_INFO
g_bp_board_class_val = 0x84, g_rx16_backplane_type = 1
BOOT INFO: load image from primary copy........
..
..
Mucho Grande line card
SYSCALL: g_bp_board_class_val = 132, g_rx16_backplane_type = 1
RW2 REV B LP
My slot = 15
Hit any key to skip IPC handshake with Active Management...
WARN IPC: No callback found for IPC msgtype 198 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 198 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 196 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 196 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 198 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 198 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 195 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 198 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 110 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 196 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 198 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 196 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 196 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 196 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 196 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 196 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 198 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 196 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 196 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 198 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 198 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 198 (from_fid = 0000d020)
WARN IPC: No callback found for IPC msgtype 198 (from_fid = 0000d020)
ipc_init() - OK
Boot Image: type=373, length=387220, checksum=7980, version = 3 5 0 2,
label = xmlb03500b, build_time=1190418661
Monitor Image: type=373, length=387220, checksum=7980, version = 3 5 0
2, label = xmlb03500b, build_time=1190418661
Application Image: type=375, length=3228334, checksum=89dd, version = 3
6 0 2, label = xmlp03600b, build_time=1193808849
Hit any key to boot as stand alone...
Active MP Slot = 32
g_mp_running_version = 3 6 0 2
System aging service will be enabled.
sys_ipc_card_config2: module_ppcr_index = 0
cam partition changed
sys_ipc_card_config2: module_ppcr_index = 1
cam partition changed
sys_ipc_card_config2: module_ppcr_index = 2
cam partition changed
sys_ipc_card_config2: module_ppcr_index = 3
sys_ipc_card_config: All card config received
HV CAM type = 255
Number of PPCR 1
g_rw_lp_revision = 100 (31603-100B)
TM DDRII support disabled
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
sand_module_open(): success
+ SAND module was opened -- success
PBIF streaming intf DCM for FAP 0 successfully locked after 1 tries
+ The FAP reset for device 0 -- success.
+ Device 0 was registered device_id=0
--> Start fap20v_cpu_test_rw()
-->> OK
--> Start write INQ memory from offset 0x0 to 0x00000280.
Finished write INQ memory.
--> Start read and compare INQ memory.
-->> OK
+ Start Initialization Sequence:
+ Loading HW params, DRAM calibration 1 (1=started).
Flash values of: FAP20V_CLBRATE_PARAMS.
FAP20V_CLBRATE_PARAMS:
sample_delay_reg:
[0]=0x294A5294 [1]=0x294A5294 [2]=0x294A5294 [3]=0x294A5294
end_win: [0]=58 [1]=55 [2]=57 [3]=55
avrg: [0]= 9 [1]= 9 [2]= 9 [3]= 9
+ fap20v_all_ctrl_cells_enable(0, FALSE) -- success.
All control cell from device are dropped.
Enable them after the device-ID is set with.
the right value (use 'fap20v_set_fap_id').
Enabling it again is done in 'fap20v_init_sequence_phase2'.
+ fap20v_init_constant_values() -- success.
+ SerDes configuration was loaded -- success.
+ DRC configuration was loaded -- success.
+ SLA_OFC configuration was loaded -- success.
+ SPI4.2 configuration was loaded -- success.
+ ZBT configuration was loaded -- success.
+ GEN configuration was loaded -- success.
- ZBT was loaded with Number-of- buffers the memory field 1,
that is 512 Kilo buffers.
Ingress DRAM was loaded with DDR buffer size field 1,
that is 128 bytes
Hence, DRAM size MUST be smaller (equal) than 65536 K-bytes.
That is, 524288 K-bits, 512 Mega-bits.
+ fap20v_hw_calibration() -- success.
+ fap20v_init_dynamic_tables() -- success.
+ fap20v_init_static_tables() -- success.
WARN IPC: Slot 32, cpu 0 DEAD!!
WARN IPC: Slot 33, cpu 0 DEAD!!
+ fap20v_hw_if_enable(0) -- success.
All device HW ifterfaces are disabled.
This interfaces includes: ZBT, DRC (to the DRAM).
+ Init device 0 sequence phase 1 -- success
+ Re-do Init sequence after DRAM calibration.
+ Init device 0 sequence phase 1 -- success
+ Configure device 0 device ID -- success
+ Enable fabric link level flow control -- success
+ Set SPI Calendar(0, SPI4_2_CAL_SRC, SPI4_2_A, ...) -- success
+ Set SPI Calendar(0, SPI4_2_CAL_SRC, SPI4_2_B, ...) -- success
+ Set SPI Calendar(0, SPI4_2_CAL_SNK, SPI4_2_A, ...) -- success
+ Set SPI Calendar(0, SPI4_2_CAL_SNK, SPI4_2_B, ...) -- success
+ Rw2_fap20v_load_sla_app dev 0 -- success
+ Load the device 0 SLA port-to-chan and chan-to-port tbls -- success.
+ At this point we should make sure that NP-SPI4 supplies
a valid sink data clock (RDCLK) and a valid source
status clock (TSCLK).
+ fap20v_spi_4_2_if_enable(0, TRUE) -- success.
+ Set SPI OOB Flow Control Calendar(0, SPI4_2_CAL_OFC, SPI4_2_A, ...)
-- success
+ Set SPI OOB Flow Control Calendar(0, SPI4_2_CAL_OFC, SPI4_2_B, ...)
-- success
+ fap20v_fc_set_physical_interface(0, AUXILIARY_CHANNEL) -- success.
+ fap20v_init_sequence_phase2(0, TRUE) -- success.
Transmission of all control cell from device are enabled.
+ END Initialization Sequence.
+ Start Application:
----rw2_fap20v_load_qdp_app ---- END.dev 0 OK
+ Device 0 QDP config -- success.
+ Enable CPU port(0, TRUE) -- success.
+ Enable recycle port(0, FALSE) -- success.
+ Disable fabric segmentation(0, FALSE) -- success.
+ Load Device 0 Egress Queues Setting -- success.
+ Configured device 0 the EGQ -- success.
+ Start device 0 high level application.
+ sweep_fap20v_multicast_spatial_app:Set SMS -- success.
+ sweep_fap20v_multicast_app(0) -- success.
+ END Application.
+ fap20v_enable_fabric_traffic(0, TRUE) -- success.
Packet drop at the LBP was stoped. I.e., Packets are streaming.
Data cell drop at from the FABRIC was stoped. I.e., Cells are
streaming.
Queue Scrubber:FirstQ 4, LastQ 8191: Rate: 162 KHZ (20 per queue per
second).
+ sweep_fap20v_scrubber_app(0) -- success.
----Init Fap20v dev 0 ---- END. OK
Read TM recovery flash - need to use default values
TM recovery set to 1, 6 times
+ FAP dev 0 was initialized -- success
Pause CPLD Initialized for tower = 0
version = 0x0000000c
so
More information about the foundry-nsp
mailing list