[f-nsp] Port state blocking?
sujith kumar
jith787 at gmail.com
Mon Feb 23 21:43:39 EST 2009
Hi chuck,
Does the other ports in the same slot is working with 2402? Could you try by
connecting a laptop to the SI-GT to confirm your port is working or not?
Have you tried using an another patch cable? Probably it should be a port
failure since you have tested all the combination.
-jith
On Tue, Feb 24, 2009 at 4:30 AM, Chuck Ufarley <markentime at gmail.com> wrote:
> Thanks, daniel--
>
> But it's still blocking. Reloading the SI-GT, blocking. Trying "no span,"
> blocking. Trying "enable," blocking. Strange. I can't figure out what's
> causing it.
>
> On Mon, Feb 23, 2009 at 10:59 AM, Daniel Kekai <Daniel.Kekai at microsoft.com
> > wrote:
>
>> On the GT go to the interface config on 4/9 and type in:
>>
>>
>>
>> no spanning-tree
>>
>>
>>
>> Then test again
>>
>>
>>
>> -daniel
>>
>>
>>
>> *From:* Chuck Ufarley [mailto:markentime at gmail.com]
>> *Sent:* Friday, February 20, 2009 1:19 PM
>>
>> *To:* Daniel Kekai
>> *Cc:* foundry-nsp at puck.nether.net
>> *Subject:* Re: [f-nsp] Port state blocking?
>>
>>
>>
>> Thanks. At this point I'm just trying to get the ports to come up, so
>> it's the simplest config in the world. 2402 connected via port 26 to SI-GT
>> on port 4/9 with a crossover cable. It's 11.0 code, and it's worked in
>> other machines, though I don't have any currently running that code.
>>
>> 2402:
>>
>> FES2402 Switch#sho run
>> Current configuration:
>> !
>> ver 04.0.00aTc1
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> ip address 192.168.0.64 255.255.255.0
>> !
>> !
>> !
>> !
>> !
>> !
>> end
>>
>> FES2402 Switch#sho int e 26
>> GigabitEthernet26 is up
>> Link Error Dampening is Disabled
>> Hardware is GigabitEthernet, address is 000c.db1d.4769 (bia
>> 000c.db1d.4769)
>> Configured speed 1Gbit, actual 1Gbit, configured duplex fdx, actual fdx
>> Configured mdi mode AUTO, actual MDI
>> Member of L2 VLAN ID 1, port is untagged, port state is FORWARDING
>> BPDU guard is Disabled, ROOT protect is Disabled
>> Link Error Dampening is Disabled
>> STP configured to ON, priority is level0
>> Flow Control is config enabled, oper enabled, negotiation disabled
>> mirror disabled, monitor disabled
>> Not member of any active trunks
>> Not member of any configured trunks
>> No port name
>> IP MTU 1500 bytes
>> 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
>> 300 second output rate: 640 bits/sec, 1 packets/sec, 0.00% utilization
>> 6461218 packets input, 423261535 bytes, 0 no buffer
>> Received 4282 broadcasts, 21834 multicasts, 6424644 unicasts
>> 0 input errors, 0 CRC, 0 frame, 0 ignored
>> 0 runts, 0 giants, DMA received 6461218 packets
>> 6746678 packets output, 1994941951 bytes, 0 underruns
>> Transmitted 189434 broadcasts, 124538 multicasts, 6432706 unicasts
>> 0 output errors, 0 collisions, DMA transmitted 6746678 packets
>> FES2402 Switch#sho int bri
>>
>> Port Link State Dupl Speed Trunk Tag Priori MAC Name
>> 1 Down None None None None No level0 000c.db1d.4750
>> 2 Down None None None None No level0 000c.db1d.4751
>> 3 Down None None None None No level0 000c.db1d.4752
>> 4 Down None None None None No level0 000c.db1d.4753
>> 5 Down None None None None No level0 000c.db1d.4754
>> 6 Down None None None None No level0 000c.db1d.4755
>> 7 Down None None None None No level0 000c.db1d.4756
>> 8 Down None None None None No level0 000c.db1d.4757
>> 9 Down None None None None No level0 000c.db1d.4758
>> 10 Down None None None None No level0 000c.db1d.4759
>> 11 Down None None None None No level0 000c.db1d.475a
>> 12 Down None None None None No level0 000c.db1d.475b
>> 13 Down None None None None No level0 000c.db1d.475c
>> 14 Down None None None None No level0 000c.db1d.475d
>> 15 Down None None None None No level0 000c.db1d.475e
>> 16 Down None None None None No level0 000c.db1d.475f
>> 17 Down None None None None No level0 000c.db1d.4760
>> 18 Down None None None None No level0 000c.db1d.4761
>> 19 Down None None None None No level0 000c.db1d.4762
>> 20 Down None None None None No level0 000c.db1d.4763
>> 21 Down None None None None No level0 000c.db1d.4764
>> 22 Down None None None None No level0 000c.db1d.4765
>> 23 Up Forward Full 100M None No level0 000c.db1d.4766
>> 24 Up Forward Full 100M None No level0 000c.db1d.4767
>> 25 Up Forward Full 1G None No level0 000c.db1d.4768
>> 26 Up Forward Full 1G None No level0 000c.db1d.4769
>> FES2402 Switch#
>>
>> SI-GT:
>>
>> ServerIronGT E-1#sho run
>> !Building configuration...
>> !Current configuration : 378 bytes
>> !
>> ver 11.0.00TD4
>> !
>> module 1 bi-0-port-wsm6-management-module
>> module 3 bi-jc-2-port-gig-module
>> module 4 bi-jc-16-port-gig-copper-module
>> !
>> context default
>> !
>> aaa authentication web-server default local
>> no enable aaa console
>> telnet server
>> username admin password .....
>> snmp-server
>> !
>> interface ethernet 4/9
>> ip address 192.168.0.77 255.255.255.0
>> !
>> end
>>
>> ServerIronGT E-1#sho int e 4/9
>> GigabitEthernet4/9 is down, line protocol is down
>> Hardware is GigabitEthernet, address is 000c.dbb5.b668 (bia
>> 000c.dbb5.b668)
>> Configured speed auto, actual unknown, configured duplex fdx, actual
>> unknown
>> Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING
>> STP configured to ON, priority is level0, flow control enabled
>> mirror disabled, monitor disabled
>> Not member of any active trunks
>> Not member of any configured trunks
>> No port name
>> Internet address is 192.168.0.77/24, MTU 1518 bytes, encapsulation
>> ethernet
>> 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
>> 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
>> 6096 packets input, 507641 bytes, 0 no buffer
>> Received 4256 broadcasts, 1838 multicasts, 2 unicasts
>> 0 input errors, 0 CRC, 0 frame, 0 ignored
>> 0 runts, 0 giants, DMA received 0 packets
>> 0 packets output, 0 bytes, 0 underruns
>> Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
>> 0 output errors, 0 collisions, DMA transmitted 0 packets
>> ServerIronGT E-1#sho int bri
>>
>> Port Link State Dupl Speed Trunk Tag Priori MAC Name
>> 4/1 Down None None None None No level0 000c.dbb5.b660
>> 4/2 Down None None None None No level0 000c.dbb5.b661
>> 4/3 Down None None None None No level0 000c.dbb5.b662
>> 4/4 Down None None None None No level0 000c.dbb5.b663
>> 4/5 Down None None None None No level0 000c.dbb5.b664
>> 4/6 Down None None None None No level0 000c.dbb5.b665
>> 4/7 Down None None None None No level0 000c.dbb5.b666
>> 4/8 Down None None None None No level0 000c.dbb5.b667
>> 4/9 Down None None None None No level0 000c.dbb5.b668
>> 4/10 Down None None None None No level0 000c.dbb5.b669
>> 4/11 Down None None None None No level0 000c.dbb5.b66a
>> 4/12 Down None None None None No level0 000c.dbb5.b66b
>> 4/13 Down None None None None No level0 000c.dbb5.b66c
>> 4/14 Down None None None None No level0 000c.dbb5.b66d
>> 4/15 Down None None None None No level0 000c.dbb5.b66e
>> 4/16 Down None None None None No level0 000c.dbb5.b66f
>> ServerIronGT E-1#
>>
>> On Fri, Feb 20, 2009 at 12:06 PM, Daniel Kekai <
>> Daniel.Kekai at microsoft.com> wrote:
>>
>> Send the output on the FES side interface and if possible the configs for
>> both the GT and FES
>>
>> Also do you have this setup working with other GT's – FES? If so are you
>> running the same code?
>>
>>
>>
>> -D
>>
>>
>>
>> *From:* Chuck Ufarley [mailto:markentime at gmail.com]
>> *Sent:* Friday, February 20, 2009 11:17 AM
>> *To:* Daniel Kekai
>> *Cc:* foundry-nsp at puck.nether.net
>> *Subject:* Re: [f-nsp] Port state blocking?
>>
>>
>>
>> It seems to be disabled. Should I enable it? This hasn't been an issue
>> in past configs.
>>
>> ServerIronGT E-1#sho span
>>
>> Spanning-tree is not configured on port-vlan 1.
>>
>> Thanks again.
>>
>> On Fri, Feb 20, 2009 at 11:01 AM, Daniel Kekai <
>> Daniel.Kekai at microsoft.com> wrote:
>>
>> Check your spanning tree
>>
>> -D
>>
>>
>>
>> *From:* foundry-nsp-bounces at puck.nether.net [mailto:
>> foundry-nsp-bounces at puck.nether.net] *On Behalf Of *Chuck Ufarley
>> *Sent:* Friday, February 20, 2009 9:51 AM
>> *To:* foundry-nsp at puck.nether.net
>> *Subject:* [f-nsp] Port state blocking?
>>
>>
>>
>> This might be a silly question, but I can't get a port to come up on a
>> ServerIron. I enabled the interface and connected it properly to a
>> FES-X2402 switch, but the J-B16GC and the J-B2Gx ports just won't come up
>> and forward. The cards have worked in other configs, but I can't get
>> anything to come out of "blocking" mode. Here are the shows (any help
>> greatly appreciated):
>>
>> ServerIronGT E-1#sho run
>> !Building configuration...
>> !Current configuration : 378 bytes
>> !
>> ver 11.0.00TD4
>> !
>> module 1 bi-0-port-wsm6-management-module
>> module 3 bi-jc-2-port-gig-module
>> module 4 bi-jc-16-port-gig-copper-module
>> !
>> context default
>> !
>> aaa authentication web-server default local
>> no enable aaa console
>> telnet server
>> username admin password .....
>> snmp-server
>> !
>> interface ethernet 4/9
>> ip address 192.168.0.77 255.255.255.0
>> !
>> end
>>
>> ServerIronGT E-1#sho run
>> !Building configuration...
>> !Current configuration : 378 bytes
>> !
>> ver 11.0.00TD4
>> !
>> module 1 bi-0-port-wsm6-management-module
>> module 3 bi-jc-2-port-gig-module
>> module 4 bi-jc-16-port-gig-copper-module
>> !
>> context default
>> !
>> aaa authentication web-server default local
>> no enable aaa console
>> telnet server
>> username admin password .....
>> snmp-server
>> !
>> interface ethernet 4/9
>> ip address 192.168.0.77 255.255.255.0
>> !
>> end
>>
>> ServerIronGT E-1#sho mod
>> Module Status Ports Starting MAC
>> S1: B0GMR WSM6 Management Module, SYSIF 2 M6, ACTIV 0
>> S2:
>> S3: J-BxG2 JetCore Gig Fiber Module, SYSIF OK 2 000c.dbb5.b640
>> S4: J-BxGC16 JetCore Gig Copper Module, SY OK 16 000c.dbb5.b660
>> ServerIronGT E-1#sho int e 4/9
>> GigabitEthernet4/9 is down, line protocol is down
>> Hardware is GigabitEthernet, address is 000c.dbb5.b668 (bia
>> 000c.dbb5.b668)
>> Configured speed auto, actual unknown, configured duplex fdx, actual
>> unknown
>> Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING
>> STP configured to ON, priority is level0, flow control enabled
>> mirror disabled, monitor disabled
>> Not member of any active trunks
>> Not member of any configured trunks
>> No port name
>> Internet address is 192.168.0.77/24, MTU 1518 bytes, encapsulation
>> ethernet
>> 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
>> 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
>> 991 packets input, 77378 bytes, 0 no buffer
>> Received 581 broadcasts, 410 multicasts, 0 unicasts
>> 0 input errors, 0 CRC, 0 frame, 0 ignored
>> 0 runts, 0 giants, DMA received 0 packets
>> 0 packets output, 0 bytes, 0 underruns
>> Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
>> 0 output errors, 0 collisions, DMA transmitted 0 packets
>> ServerIronGT E-1#
>>
>> +++++
>>
>> Thanks much, everyone.
>>
>>
>>
>>
>>
>
>
> _______________________________________________
> foundry-nsp mailing list
> foundry-nsp at puck.nether.net
> http://puck.nether.net/mailman/listinfo/foundry-nsp
>
--
-Sujith
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/foundry-nsp/attachments/20090224/a3948809/attachment-0001.html>
More information about the foundry-nsp
mailing list