[f-nsp] Port state blocking?

[Jason Pope]

I think you need to enable the port.

jp


On Fri, Feb 20, 2009 at 11:51 AM, Chuck Ufarley <markentime at gmail.com> wrote:
> This might be a silly question, but I can't get a port to come up on a
> ServerIron.  I enabled the interface and connected it properly to a
> FES-X2402 switch, but the J-B16GC and the J-B2Gx ports just won't come up
> and forward.  The cards have worked in other configs, but I can't get
> anything to come out of "blocking" mode.  Here are the shows (any help
> greatly appreciated):
>
> ServerIronGT E-1#sho run
> !Building configuration...
> !Current configuration : 378 bytes
> !
> ver 11.0.00TD4
> !
> module 1 bi-0-port-wsm6-management-module
> module 3 bi-jc-2-port-gig-module
> module 4 bi-jc-16-port-gig-copper-module
> !
> context default
> !
> aaa authentication web-server default local
> no enable aaa console
> telnet server
> username admin password .....
> snmp-server
> !
> interface ethernet 4/9
>  ip address 192.168.0.77 255.255.255.0
> !
> end
>
> ServerIronGT E-1#sho run
> !Building configuration...
> !Current configuration : 378 bytes
> !
> ver 11.0.00TD4
> !
> module 1 bi-0-port-wsm6-management-module
> module 3 bi-jc-2-port-gig-module
> module 4 bi-jc-16-port-gig-copper-module
> !
> context default
> !
> aaa authentication web-server default local
> no enable aaa console
> telnet server
> username admin password .....
> snmp-server
> !
> interface ethernet 4/9
>  ip address 192.168.0.77 255.255.255.0
> !
> end
>
> ServerIronGT E-1#sho mod
>     Module                                 Status    Ports Starting MAC
> S1: B0GMR WSM6 Management Module, SYSIF 2  M6, ACTIV   0
> S2:
> S3: J-BxG2 JetCore Gig Fiber Module, SYSIF OK          2   000c.dbb5.b640
> S4: J-BxGC16 JetCore Gig Copper Module, SY OK         16   000c.dbb5.b660
> ServerIronGT E-1#sho int e 4/9
> GigabitEthernet4/9 is down, line protocol is down
>   Hardware is GigabitEthernet, address is 000c.dbb5.b668 (bia
> 000c.dbb5.b668)
>   Configured speed auto, actual unknown, configured duplex fdx, actual
> unknown
>   Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING
>   STP configured to ON, priority is level0, flow control enabled
>   mirror disabled, monitor disabled
>   Not member of any active trunks
>   Not member of any configured trunks
>   No port name
>   Internet address is 192.168.0.77/24, MTU 1518 bytes, encapsulation
> ethernet
>   300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
>   300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
>   991 packets input, 77378 bytes, 0 no buffer
>   Received 581 broadcasts, 410 multicasts, 0 unicasts
>   0 input errors, 0 CRC, 0 frame, 0 ignored
>   0 runts, 0 giants, DMA received 0 packets
>   0 packets output, 0 bytes, 0 underruns
>   Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
>   0 output errors, 0 collisions, DMA transmitted 0 packets
> ServerIronGT E-1#
>
> +++++
>
> Thanks much, everyone.
>
> _______________________________________________
> foundry-nsp mailing list
> foundry-nsp at puck.nether.net
> http://puck.nether.net/mailman/listinfo/foundry-nsp
>