[f-nsp] Foundry EdgeIron EIF24G

[Eric Roach]

Savvas,

I am copying the instructions on configuring vlans and then date and code afterwards.
untagged ethernetUse this command to assign ports as untagged members of a port-based VLAN. Use the 
ports from a port-based VLAN.no form to removeSyntax
untagged ethernet 
no untagged ethernet interface [to interface]interface [to interface]• 
• interface - Specifies a port number, or the start or end of a port range, to assign to the VLAN.unit/port- 
- 
• unit - This is device 1.port - Port number.to - Specifies the end of a port number range.Default Setting
None
Command Mode
VLAN Configuration
ExampleThe following example shows how to assign switch ports 1 to 8 as untagged members of VLAN 222.
 tagged ethernetUse this command to assign ports as tagged members of a port-based VLAN. Use the 
from the port-based VLAN.no form to remove portsSyntax
tagged ethernet 
no tagged ethernet interface [to interface]interface [to interface]• 
• interface - Specifies a port number, or the start or end of a port range, to assign to the VLAN.unit/port- 
- 
• unit - This is device 1.port - Port number.to - Specifies the end of a port number range.Default Setting
Nonedual-modeUse this command to enable a tagged VLAN port to accept and transmit both tagged and untagged traffic. Use
the no form to restore the default setting.Syntaxdual-mode [
no dual-mode
• vlan_id]vlan_id - Specifies the default VLAN ID for the port. (Range: 1-4094, no leading zeroes).Default Setting
Disabled
Command UsageConfiguring a tagged port as a dual-mode port allows it to accept and transmit both tagged traffic and untagged
traffic at the same time. A dual-mode port transmits only untagged traffic on its default VLAN (that is either
VLAN 1, or a user specified VLAN ID), and only tagged traffic on all other VLANs.Command Mode
Interface Configuration
ExampleThe following example shows how to enable dual-mode on port 5 and set its default VLAN ID to 10.Console(config)#vlan 10 by port
Console(config-vlan-10)#untagged ethernet 1/1
Console(config)#vlan 222 by port
Console(config-vlan-222)#tagged ethernet 1/5
Console(config)#interface ethernet 1/5
Console(config-if)#dual-mode 10
Console(config-if)#
22421                                                                 3/24/2005 12:36:33 AM                                                  File Folder
22518                                                                 4/4/2005 7:04:42 PM                                                      File Folder
… many in between
22732                      4/21/2009 11:18:04 AM          File Folder


Eric 

Hi,

I have recently purchased a few Foundry EdgeIron EIF24G models. I am having some trouble using tagged vlans and the OS seems ancient, the configuration has been verified by multiple engineers now so I figured maybe a firmware upgrade should get me where I need to be.

Is there anyone who can help me with recent software for these units? My sh ver output:

Vty-0#sh ver
Unit1
Serial number          :AN00001310
Service tag            :
Hardware version      :R01
Number of ports        :24
Main power status      :up
Redundant power status :not present
Agent(master)
Unit id                :1
Loader version        :1.0.0.0
Boot rom version      :1.0.0.1
Operation code version :2.0.1..9

Any help would be much appreciated.

Thanks,
Savvas
_______________________________________________
foundry-nsp mailing list
foundry-nsp at puck.nether.net
http://puck.nether.net/mailman/listinfo/foundry-nsp