[f-nsp] Interoperability issue between Windows NLB cluster with Foundry SX800

[Sujith]

Thank you Jared.

I will test it out in my office lab and if it goes as suggested, I will
implement in the client's network.

Thanks again for your time and suggestion.

-Sujith

On Mon, Jun 14, 2010 at 3:36 AM, Jared Valentine <hidden at xmission.com>wrote:

>  Sounds like you need to map a static arp entry to multiple Ethernet
> ports?  I believe it’s possible with the SX800, but you’ll have to use a
> hairpin in order to get the functionality to work.  These instructions
> assume the following:
>
>
>
> SX800 is routing
>
> Servers use the SX800 as their default gateway
>
> Servers are in VLAN 100
>
> SX800 VLAN100 VE address is 10.0.0.1
>
>
>
> Here’s something to try:
>
>
>
> 1.)    Remove VE100 from VLAN100.
>
> 2.)    Add another port to VLAN100 untagged (example 2/1)
>
> 3.)    Create new VLAN (101)
>
> 4.)    Add single port, untagged, into VLAN101 (example eth 2/2)
>
> 5.)    Create VE101 in VLAN101
>
> 6.)    Assign VE101 with 10.0.0.1
>
> 7.)    “Loop” 2/1 to 2/2
>
> 8.)    Create the static-arp entry on port 2/2
>
>
>
> You can tweak these instructions for other scenarios (SX800 not routing,
> just switching), but the concept remains the same.  If the SX800 isn’t
> routing, then you’ll create VLAN101, move the physical uplink from VLAN100
> to VLAN101, loop VLANs 100/101, add your static-arp entry to the loop port
> in VLAN101.
>
>
>
> Good luck,
>
>
>
> -Jared
>
>
>
>
>
>
>
> *From:* foundry-nsp-bounces at puck.nether.net [mailto:
> foundry-nsp-bounces at puck.nether.net] *On Behalf Of *Sujith
> *Sent:* Wednesday, June 02, 2010 7:27 PM
> *To:* foundry-nsp
> *Subject:* [f-nsp] Interoperability issue between Windows NLB cluster with
> Foundry SX800
>
>
>
> Hello,
>
>
>
> Thank you for your valuable suggestions and time.
>
>
>
> The client is having a Windows NLB cluster configured for an application
> and is terminated to the Foundry switch.  The Windows cluster is receiving
> request constantly on one server and not on other server.
>
>
>
> We tried configuring static MAC address on both the Ethernet ports as
> suggested by Foundry guide for Windows NLB setup and followed some
> guidelines from Cisco guide also.  Both the guidance were failing to deliver
> the request on both the servers.
>
>
>
> The client is running a Hyper-V on two separate physical servers and each
> Hyper-V is holding 3 Nos. of virtual machines.  The Windows NLB cluster is
> configured only for 1 Virtual machine in each physical server.
>
>
>
> The servers are terminated in the Foundry SX800.  The windows NLB cluster's
> are configured to work in Unicast mode and also tested with Multicast mode
> also.  On both the testing, we are not getting the results on both the
> servers.  The Windows NLB cluster is working perfectly with Cisco switch
> without any issue.
>
>
>
> The client tested the Windows NLB cluster configured separately on the
> physical servers (test bench) which is connected to the Foundry switch and
> we get the results as expected.  But when tested with Windows NLB cluster
> configured on a Virtual machine, it fails.
>
>
>
> Do someone have come across this issue and is there any workaround to
> resolve the same?
>
>
>
> Thanks
>
> -Sujith
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/foundry-nsp/attachments/20100614/f807efa5/attachment-0001.html>