[f-nsp] E1MG-100FX-IR-OM link not coming up on NI-XMR-1Gx20-SFP

[Bill]

I have some new brocade compatible optics (SFP) that we are trying to use 
for a customer that are not working.

E1MG-100FX-IR-OM is a 100FX (yes, 100 mbit) optic that is supposed to work 
in the NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module.

The manufacturer tells me that Brocade requires 3.9.0 code for these to 
work. Since the router is running 5.2.0d, maybe they are talking about 
FPGA code on the 1Gx20 card??

show media shows correct:

SSH at router#show media e 4/11
Port 4/11:
     Type  : SFP (LHA-1310nm)
     Vendor:          BROCADE         , Version:                 1.0
     Part# :          E1MG-100FX-IR-OM, Serial#:     S1306014XXX
All show media done
SSH at router#show media e 4/12
Port 4/12:
     Type  : SFP (LHA-1310nm)
     Vendor:          BROCADE         , Version:                 1.0
     Part# :          E1MG-100FX-IR-OM, Serial#:     S1306018XXX
All show media done

show optic shows correct:

SSH at router#show optic 4
  Port  Temperature   Tx Power     Rx Power     Tx Bias Current
+----+-----------+-------------+------------+----------------+
4/11   39.6484 C  -011.1294 dBm -011.1520 dBm   21.582 mA
        Normal       Normal           Normal      Normal
4/12   50.6210 C  -009.8254 dBm -005.8787 dBm   24.198 mA
        Normal       Normal           Normal      Normal

With a loopback plug in the SFP, the port still shows down/down:

SSH at router#show int e 4/11
GigabitEthernet4/11 is down, line protocol is down
   STP Root Guard is disabled, STP BPDU Guard is disabled
   Hardware is GigabitEthernet, address is 000c.dbe8.4b9a (bia 000c.dbe8.4b9a)
   Configured speed auto, actual unknown, configured duplex fdx, actual 
unknown
   Member of VLAN 999 (untagged), port is in untagged mode, port state is 
Disabled
   STP configured to ON, Priority is level0, flow control disabled
   Priority force disabled, Drop precedence level 0, Drop precedence force 
disabled
   dhcp-snooping-trust configured to OFF
   mirror disabled, monitor disabled
   LACP BPDU Forwarding:Disabled
   Not member of any active trunks
   Not member of any configured trunks
   Port name is BILL TESTING 100FX OPTICS 8/27/2013
   Internet address is 10.200.0.1/29, MTU 9200 bytes, encapsulation ethernet
   Cluster L2 protocol forwarding enabled
   300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
   300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
   0 packets input, 0 bytes, 0 no buffer
   Received 0 broadcasts, 0 multicasts, 0 unicasts
   0 input errors, 0 CRC, 0 frame, 0 ignored
   0 runts, 0 giants
   NP received 0 packets, Sent to TM 0 packets
   NP Ingress dropped 0 packets
   0 packets output, 0 bytes, 0 underruns
   Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
   0 output errors, 0 collisions
   NP transmitted 0 packets, Received from TM 0 packets

Port configuration:

SSH at router#sho run int e 4/11
interface ethernet 4/11
  port-name BILL TESTING 100FX OPTICS 8/27/2013
  enable
  route-only
  ip address 10.200.0.1/29
  no flow-control

Router and firmware versions:

==========================================================================
SL 1: NI-XMR-10Gx4 4-port 10GbE Module (Serial #: PR1506XXXX, Part #: 
31546-203A)
Boot     : Version 5.2.0T175 Copyright (c) 1996-2009 Brocade 
Communications Systems, Inc.
Compiled on Jun  7 2011 at 17:06:54 labeled as xmlprm05200
  (514997 bytes) from boot flash
Monitor  : Version 5.2.0T175 Copyright (c) 1996-2009 Brocade 
Communications Systems, Inc.
Compiled on Jun  7 2011 at 17:07:18 labeled as xmlb05200
  (515819 bytes) from code flash
IronWare : Version 5.2.0dT177 Copyright (c) 1996-2009 Brocade 
Communications Systems, Inc.
Compiled on Mar  2 2012 at 19:00:00 labeled as xmlp05200d
  (6529868 bytes) from Primary
FPGA versions:
Valid PBIF Version = 3.24, Build Time = 8/4/2010 16:29:00

Valid XPP Version = 6.23, Build Time = 2/4/2011 9:7:00

Valid XGMAC Version = 0.15, Build Time = 10/14/2010 16:31:00

X10G2MAC 0
X10G2MAC 1
666 MHz MPC 8541 (version 8020/0020) 333 MHz bus
512 KB Boot Flash (AM29LV040B), 16 MB Code Flash (MT28F640J3)
1024 MB DRAM, 8 KB SRAM, 0 Bytes BRAM
PPCR0: 0K entries CAM, 0K PRAM, 0K AGE RAM
PPCR1: 0K entries CAM, 0K PRAM, 0K AGE RAM
LP Slot 1 uptime is 36 days 15 hours 1 minutes 18 seconds

==========================================================================
SL 4: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module (Serial #: SA1907XXXX, 
Part #: 35570-200B)
Boot     : Version 5.2.0T175 Copyright (c) 1996-2009 Brocade 
Communications Systems, Inc.
Compiled on Jun  7 2011 at 17:06:54 labeled as xmlprm05200
  (514997 bytes) from boot flash
Monitor  : Version 5.2.0T175 Copyright (c) 1996-2009 Brocade 
Communications Systems, Inc.
Compiled on Jun  7 2011 at 17:07:18 labeled as xmlb05200
  (515819 bytes) from code flash
IronWare : Version 5.2.0dT177 Copyright (c) 1996-2009 Brocade 
Communications Systems, Inc.
Compiled on Mar  2 2012 at 19:00:00 labeled as xmlp05200d
  (6529868 bytes) from Primary
FPGA versions:
Valid PBIF Version = 3.24, Build Time = 8/4/2010 16:29:00

Valid XPP Version = 6.23, Build Time = 2/4/2011 9:7:00

BCM5695GMAC 0
BCM5695GMAC 1
666 MHz MPC 8541 (version 8020/0020) 333 MHz bus
512 KB Boot Flash (AM29LV040B), 16 MB Code Flash (MT28F640J3)
1024 MB DRAM, 8 KB SRAM, 0 Bytes BRAM
PPCR0: 0K entries CAM, 0K PRAM, 0K AGE RAM
LP Slot 4 uptime is 36 days 15 hours 1 minutes 50 seconds
==========================================================================