<div>Yeah, I wasn't sure about that, I am probably thinking about the newer chassis code. Sorry Calvin.</div>
<div> </div>
<div>Mike<br></div>
<div class="gmail_quote">On Mon, Jan 12, 2009 at 2:42 PM, Oliver Adam <span dir="ltr"><<a href="mailto:oadam@madao.de">oadam@madao.de</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid">Dual-mode is not supported at the ServerIron XL as far as I remember - dual-mode ports are only available using the devices which came out after the XL. The XL is a pretty old box.<br>
<br>- Oliver<br><br>At 23:36 12.01.2009, Calvin Gorriaran wrote:<br>
<blockquote class="gmail_quote" style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid">Content-Language: en-US<br>Content-Type: multipart/alternative;<br><br>boundary="_000_3DFFCADFA43AB74890E06352129CDE6C19D707EDE9MBX1EXCHPRODU_"
<div>
<div></div>
<div class="Wj3C7c"><br><br>Hi Mike,<br><br>These are my choices in an interface that has been tagged. I think I may just be too far behind on firmware.<br><br>ver 07.4.01T12<br><br>(config-if-e100-1)#<br> auto-gig Handshaking with other Gig port to exchange capability<br>
info<br> broadcast Broadcast traffic<br> cache-group TCS cache group<br> clear Reset functions/remove keys<br> dhcp-gateway-list DHCP Assist - set gateway address for each subnet<br>
disable Disable<br> enable Enable<br> end End config-level commands<br> exit Exit current level commands<br> flow-control 802.3x flow control on full duplex port<br>
fw-group firewall group<br> ip IP commands<br> ip-multicast-disable Disable IP multicast on this interface<br> ip-policy IP access filter commands<br> ipg10 Inter-Packet Gap delay for 10M Ethernet<br>
ipg100 Inter-Packet Gap delay for 100M Ethernet<br> ipg1000 Inter-Packet Gap delay for Gig Ethernet<br> mac MAC filter commands<br> monitor Monitored port<br>
multicast Multicast traffic<br> neg-off No handshake for the port<br> no Undo commands<br> phy-mode Bay 28000 compatibility mode<br> port-name Assign alphanumeric port name<br>
pvst-mode Interoperate with Cisco PVST+ for multi-spanning tree<br> qos-priority QOS priority<br> quit Exit to user level<br> rshow Remote show system information<br>
show Show system information<br> spanning-tree STP port commands<br> speed-duplex 100 or 10, half or full<br> unknown-unicast Unknown unicast<br> write Write running configuration to memory or terminal<br>
<br></div></div>
<div class="Ih2E3d">_______________________________________________<br>foundry-nsp mailing list<br><a href="mailto:foundry-nsp@puck.nether.net" target="_blank">foundry-nsp@puck.nether.net</a><br><a href="http://puck.nether.net/mailman/listinfo/foundry-nsp" target="_blank">http://puck.nether.net/mailman/listinfo/foundry-nsp</a><br>
</div></blockquote><br><br></blockquote></div><br>