Hi all--<br><br>I've got an FI-SX 800 with a FI-2XGMR4 PREM and a couple of FI-42XGs, and I can't seem to get the ports on the 2XGs to come up. There's nothing connected to the box at all. Reloads and power downs keep repeating a port state BLOCKING. Can't figure out why. Console output is below. Anyone got any advice?<br>
<br>FastIron SX 800 Router#sho run<br>Current configuration:<br>!<br>ver 05.1.00T3e3<br>!<br>module 1 fi-sx4-2-port-10g-module<br>module 2 fi-sx4-2-port-10g-module<br>module 9 fi-sx4-2-10g-port-management-module<br>!<br>!<br>
!<br>!<br>!<br>!<br>!<br>!<br>!<br>!<br>!<br>!<br>!<br>!<br>!<br>!<br>end<br><br>FastIron SX 800 Router#sho ver<br><br>==========================================================================<br>Active Management CPU [Slot-9]:<br>
SW: Version 05.1.00T3e3 Copyright (c) 1996-2009 Brocade Communications Systems<br>, Inc.<br> Compiled on May 12 2009 at 22:13:55 labeled as SXR05100<br> (3395303 bytes) from Primary SXR05100.bin<br> BootROM: Version 05.1.00T3e5 (FEv2)<br>
Serial #: SA17085232<br> HW: Chassis FastIron SX 800-PREM (PROM-TYPE SX-FIL3U)<br>==========================================================================<br>SL 1: SX-FI42XG 2-port 10G<br> Serial #: CH05080069<br>
P-ASIC 0: type 01D1, rev 00 subrev 00<br> P-ASIC 1: type 01D1, rev 00 subrev 00<br>==========================================================================<br>SL 2: SX-FI42XG 2-port 10G<br> Serial #: CH05080080<br>
P-ASIC 2: type 01D1, rev 00 subrev 00<br> P-ASIC 3: type 01D1, rev 00 subrev 00<br>==========================================================================<br>SL 9: SX-FI2XGMR4 2-port Management<br> Serial #: CH34070027<br>
P-ASIC 16: type 01D1, rev 00 subrev 00<br> P-ASIC 17: type 01D1, rev 00 subrev 00<br>==========================================================================<br>Active Management Module:<br> 660 MHz Power PC processor 8541 (version 32/0020) 66 MHz bus<br>
512 KB boot flash memory<br>16384 KB code flash memory<br> 512 MB DRAM<br>The system uptime is 22 minutes 9 seconds<br>The system : started=cold start<br><br>FastIron SX 800 Router#sho mod<br> Module Status Ports Starting MAC<br>
F1: SX-FISF Switch Fabric active<br> F2: SX-FISF Switch Fabric active<br> S1: SX-FI42XG 2-port 10G OK 2 0012.f226.d700<br> S2: SX-FI42XG 2-port 10G OK 2 0012.f226.d718<br>
S3:<br> S4:<br> S5:<br> S6:<br> S7:<br> S8:<br> S9: SX-FI2XGMR4 2-port Management Active 2 0012.f226.d7c0<br> { Status : OK }<br>S10: Standby 0<br>FastIron SX 800 Router#sho int e 1/1<br>
10GigabitEthernet1/1 is down, line protocol is down<br> Hardware is 10GigabitEthernet, address is 0012.f226.d700 (bia 0012.f226.d700)<br> Configured speed 10Gbit, actual unknown, configured duplex fdx, actual unknown<br>
<br> Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING<br> BPDU guard is Disabled, ROOT protect is Disabled<br> Link Error Dampening is Disabled<br> STP configured to ON, priority is level0<br> Flow Control is enabled<br>
mirror disabled, monitor disabled<br> Not member of any active trunks<br> Not member of any configured trunks<br> No port name<br> IPG XGMII 96 bits-time<br> IP MTU 1500 bytes, encapsulation ethernet<br> 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization<br>
300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization<br> 0 packets input, 0 bytes, 0 no buffer<br> Received 0 broadcasts, 0 multicasts, 0 unicasts<br> 0 input errors, 0 CRC, 0 frame, 0 ignored<br> 0 runts, 0 giants<br>
0 packets output, 0 bytes, 0 underruns<br> Transmitted 0 broadcasts, 0 multicasts, 0 unicasts<br> 0 output errors, 0 collisions<br> Relay Agent Information option: Disabled<br>FastIron SX 800 Router#sho int e 1/2<br>
10GigabitEthernet1/2 is down, line protocol is down<br> Hardware is 10GigabitEthernet, address is 0012.f226.d701 (bia 0012.f226.d701)<br> Configured speed 10Gbit, actual unknown, configured duplex fdx, actual unknown<br>
<br> Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING<br> BPDU guard is Disabled, ROOT protect is Disabled<br> Link Error Dampening is Disabled<br> STP configured to ON, priority is level0<br> Flow Control is enabled<br>
mirror disabled, monitor disabled<br> Not member of any active trunks<br> Not member of any configured trunks<br> No port name<br> IPG XGMII 96 bits-time<br> IP MTU 1500 bytes, encapsulation ethernet<br> 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization<br>
300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization<br> 0 packets input, 0 bytes, 0 no buffer<br> Received 0 broadcasts, 0 multicasts, 0 unicasts<br> 0 input errors, 0 CRC, 0 frame, 0 ignored<br> 0 runts, 0 giants<br>
0 packets output, 0 bytes, 0 underruns<br> Transmitted 0 broadcasts, 0 multicasts, 0 unicasts<br> 0 output errors, 0 collisions<br> Relay Agent Information option: Disabled<br>FastIron SX 800 Router#<br><br><br>As always, your help is greatly appreciated.<br>
<br>Thanks.<br><br>--Chuck<br><br>