<html>
<head>
<meta content="text/html; charset=ISO-8859-1"
http-equiv="Content-Type">
</head>
<body bgcolor="#FFFFFF" text="#000000">
<div class="moz-cite-prefix">Your application image doesn't match
then most likely.<br>
<br>
Somehow the linecard doesn't recognize the difference between some
5300x and 5400x application images, so it doesn't do an automatic
lp sync on boot. Also attempting a manual lp sync doesn't see a
problem.<br>
<br>
Boot the card in interactive/monitor mode ('rcon lp 3' from
console to get into the linecard shell and hit the b when it says
so) and then make sure you upgrade the lp monitor, boot,
application, xpp, sp2 and xgmac images from the generic
commandline in your XMR. Then powercycle the linecard with a
power-off and power-on and and it should work.<br>
<br>
<br>
<br>
On 7/4/13 2:33 PM, Jeroen Oldenhof wrote:<br>
</div>
<blockquote cite="mid:51D56B88.3020200@cj2.nl" type="cite">
<meta http-equiv="Content-Type" content="text/html;
charset=ISO-8859-1">
<blockquote type="cite">
<pre>On Thu, Jun 21, 2012 at 04:03:54PM +0300, Alexander Shikoff wrote:<i>
</i>><i> </i><i>
</i>><i> pbif_ager_linklist_init: PBIF #0 pLinkListEntry base 0x08f24000
</i>><i> rw2_cpu_pkt_buf_init : rx_priority_mode set failed after 6 tries.
</i>><i> Module is dow
</i>><i> NetIron XMR/MLX Boot Monitor Version 5.3.00
</i>><i> Enter 'b' to stop at boot monitor
</i>><i>
</i>><i> ... and repeats again.
</i>
Thanks to all who answered including private mails.
It was not a problem of wrong module type in configuration etc.
I've downgraded IronWare to 5.2 and now modules are ok:
<a moz-do-not-send="true" href="http://puck.nether.net/mailman/listinfo/foundry-nsp">telnet at NetIron</a> MLX-16 Router#show module
Module Status Ports Starting MAC
M1 (upper): BR-MLX-MR2-M Management Module Active
M2 (lower):
F1: NI-X-HSF Switch Fabric Module Active
F2: NI-X-HSF Switch Fabric Module Active
F3: NI-X-HSF Switch Fabric Module Active
F4:
S1: NI-MLX-10Gx8-D 8-port 10GbE (D) Module CARD_STATE_UP 8 0024.38a1.c900
S2: NI-MLX-10Gx8-D 8-port 10GbE (D) Module CARD_STATE_UP 8 0024.38a1.c930
I will try upgrading to 5.3 later once more time in order to check whether
it causes that problem.</pre>
</blockquote>
<br>
Hi,<br>
<br>
we were facing the same problem with a BR-MLX-10Gx4-X card in an
XMR chassis. The card constantly rebooted after the message<br>
<br>
rw2_cpu_pkt_buf_init : rx_priority_mode set failed after 6
tries.<br>
<br>
We were running software 5.3.0b. We performed an upgrade to 5.3.0c
and after that all was fine:<br>
<br>
#show module<br>
Module Status Ports
Starting MAC<br>
M1 (left): NI-XMR-MR Management Module Active<br>
..<br>
S3: BR-MLX-10Gx4-X 4-port 10GbE Module CARD_STATE_UP 4
748e.f85c.2d60<br>
<br>
It presume therefore there is an issue with version 5.3.0b in
relation with this linecard.<br>
<br>
Best,<br>
- Jeroen<br>
<br>
<br>
<br>
<br>
<i><br>
</i> <br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<br>
<pre wrap="">_______________________________________________
foundry-nsp mailing list
<a class="moz-txt-link-abbreviated" href="mailto:foundry-nsp@puck.nether.net">foundry-nsp@puck.nether.net</a>
<a class="moz-txt-link-freetext" href="http://puck.nether.net/mailman/listinfo/foundry-nsp">http://puck.nether.net/mailman/listinfo/foundry-nsp</a></pre>
</blockquote>
<br>
<br>
<pre class="moz-signature" cols="72">--
Jeroen Wunnink
Senior Network Engineer / NOC Team Lead
Atrato IP Networks
<a class="moz-txt-link-abbreviated" href="mailto:jeroen.wunnink@atrato.com">jeroen.wunnink@atrato.com</a>
Phone: +31 20 82 00 623</pre>
</body>
</html>